Question about Ford Fairmont

Open Question

Harmonic balancer removal ba falcon - Fairmont Ford Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: BAD HARMONIC BALANCER

To remove the harmonic balancer on my 1992 Pathfinder, I needed to loosen the alternator and power steering belts, remove the cooling fan (4 10 mm nuts), remove the radiator (2 10 mm  bolts hold it to the frame, remove top and bottom hose [The drain **** is covered by what appears to be a coolant line], as well as the overflow tube to the reservoir. With a 3/4" impact gun and a 27 mm socket, remove the bolt that retains the alt, ps shieves and the harmonic balancer to the crankshaft. With a large 3 jaw puller, remove the harmonic balancer with the pully sheives as an assembly. I do not recommend attempting the removal without the puller.
To  put it back on, you will need a large torque wrench for the crankbolt and a small torque wrench for with a crowsfoot for the fan nuts.

Posted on Dec 01, 2008

  • 548 Answers

SOURCE: Remove the harmonic balancer without a puller?

You can try simply wiggling the balancer and see if you get lucky. A few taps with a rubber mallet may convince it to come free. Worst case get the kit. You should not need to remove the radiator. Do make sure that you have the engine blocked so you don't lose your timing mark placement.

Posted on Mar 12, 2009

  • 1 Answer

SOURCE: ba falcon - wish to remove steering wheel

ave aproblem wit my air bag the light turn on and off quen you help me please

Posted on Mar 28, 2009

  • 64 Answers

SOURCE: Mitsubishi Eclipse Harmonic Balancer 3.0L Removal

There is a panel inside the wheel well that you can take off that gives you perfect access to the harmonic balancer. A special tool is required. i had my dad make one because he has access to whatever he needs at the factory. but you can get them at the dealer. i have no clue how much they cost. I can't see any way of doing it without the special tool. after you get the tool its pretty simple to get off. it takes alot of force to break the bolt loose though. i used the handle off my jack as a cheater bar. hope this helps...

Posted on Jun 29, 2009

  • 12 Answers

SOURCE: How to Remove the Rear Bumper - BA Fairmont/Falcon

Firstly, you need to remove the rear splash shields from within the rear wheel arches and also the tail lights. Then remove the scrivets from the lover edge of the bar. Next remove the scuff plate at the boot opening and fold the carpet back. There are four nuts which hold the bar on, undo these and then lift the sides of the bar up and pull out. The bar has large clips on the side which hold it in place.

Posted on Aug 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove rear axle from 2004 ba ford falcon


Hi there.
Well first jack up the rear end of car then block up the front wheels (front and rear) and put stands under the rear jacking points STILL keeping the pressure on the jack, clamp the rear brake pipe that comes from the body to the rear axle and clamp with a small clamp
but dont tighten to tight remove the flex pipe and also the rear shockers from the axle ,then the spring u bolts and then the hand brake cable from the center adjuster,now it should only leave your tail shaft 4 nuts/bolts.
But why are you removing the rear/axle????

May 04, 2014 | 2005 Ford Falcon

1 Answer

Harmonic balancer remove replace


i dont think is your harmonic balancer that dont make any sound check all the pulleys cose to change the harmonic ba... you havto remove and change your crank pulley along with it

Jan 29, 2014 | Plymouth Cars & Trucks

1 Answer

I need the location of the harmonic balancer on my 2.2l Ecotec engine. Car is 2004 Chevrolet Cavalier LS.


CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

May 21, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

2 Answers

I need a manual for a 2004 Ford Falcon BA Futura


Hello,
Please kindly follow the link below to get the manual you requsted for;
http://fitripdf.com/books/ba-gt-ford-falcon-service-manual-2.html


thank you for using fixya

Dec 19, 2010 | Ford Futura Cars & Trucks

1 Answer

V8 motor viabrates when revving


Access and removal can be done from underneath. Remove all the belts. Remove the bolt from the center of the balancer. Then you will need to get a puller to remove the balancer. They can be a little pricey to purchase, but you need it. You can do it from the top, but you probably would need to remove the fan from the water pump to get enough room to work. It's your option.

Mar 16, 2009 | 1993 Ford Mustang

2 Answers

Harmonic balancer


what are the steps to removing a harmonic balancers

Oct 18, 2008 | 1997 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...