Question about Honda Civic

1 Answer

Rear spindle removing old race from spindle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 3,799 Answers

Use a bearing puller, they are available from most auto parts dealers. Sometimes called a flywheel puller.

Posted on Apr 30, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove a rear hub on a 04 kia sedona?


Call Kia with your VIN to make sure yours wasn't affected by the recall. You may be able to have that rear bearing replaced for free at Kia.

HUBCAP & OUTER BEARING REPLACEMENT PROCEDURE: 1. Remove the two (2) cross-tip locating screws on the brake drum.

2. Remove the brake drum.

3. Remove cotter pin and cover set.

4. Remove nut, claw washer, outer bearing and hub assembly.

5. Inspect inner bearing area in both hubs for any sign of moisture, corrosion, grease discoloration or contamination. If "yes" discard entire hub and replace with new assembly. If "no" proceed with outer bearing replacement below: 6. Carefully remove the outer bearing race from the hub. If the hub assembly is damaged then replace the hub assembly as a complete unit. (If inner seal is damaged while removing the outer race replace with new seal.)

7. Clean all contaminated grease from outer bearing cavity of the hub.

8. Install a new outer race into the hub using an appropriate race installation tool.

9. Apply grease MS511-33 WBG2 or equivalent to the hub assembly and the new bearing(s) especially to the shaded areas.

10. Install hub assembly, new pre-greased outer bearing and new claw washer on spindle. (Or alternatively, install entire new hub assembly, as supplied). Ensure bearings are properly seated then tighten hub/spindle nut, torque nut to 20-25 lb-ft (27-33 Nm.) Verify hub spins freely without signs of binding or excessive play.

11. Install new cover set and cotter pin; never reuse the old cotter pin.

12. Install new hub cap with Loctite # 5910(TM) or equivalent sealant to prevent moisture intrusion.

13. Install the rear brake drum using tapered locating screws.

14. Install rear wheels and torque lug nuts to proper specification. (65-79 lb-ft) (88-108 Nm, 9-11 kgm)

15. Lower vehicle.

Dec 30, 2014 | Cars & Trucks

1 Answer

I have a ford focus se 2001 and the two rear wheel barrings keep going bad! We replace them and they go bad every four months! The car has brand new tires and they continue to go out! Any ideas????


If this does not have sealed bearings then you have the old style bearing. The old style bearings are 2 parts, the cone and the race. If you only replace the cone, it will quickly fail because a race that is scored up is abrasive.

If the bearing race has not been properly installed it will be lopsided in the seat of the hub. There is also a process for installing the race, never, ever draw the race into the hub using the old or new bearing. You will scar, flatten, or bend both parts.

There is a process for packing the bearing with grease, and there is a front and back to the seal for the hub for these old style units.

Now if the bearing is a third style, a sealed trailer hub style that bolts onto the axle shaft, this style acts both as the spindle and a permanent bearing. Some Manufactuers go this route for simplicity, but some chose to have a removeable sealed bearing as yet another combination.

Do not understand if you are saying just the bearings go bad or the tires go bad too. Usually bad bearings cause the tires to go bad, not the other way around.

Sometimes you have problems with the rear Emergency brake pads, some need to be loosened and readjusted when the brakes are taken off to get at the hub.

Please rate my info.

Jan 27, 2013 | Cars & Trucks

1 Answer

Replacing front wheel bearings on 97 dodge 3500 2wd


If its to wheel drive than it will have a inner and outer bearing. 1. Remove the caliper 2. Remove the dust cap from the center of he rotor 3. Remove the cotter pin from the spindle 4. Remove the castellated nut 5. Remove the nut and washwer 6. Remove the outer bearing 7. Remove the rotor from the spindle 8. Remove the grease seal from the back of the rotor 9. Remove the inner bearing Clean the grease out of the rotor. Use a punch to remove the inner and outer races from the hub. Install the new races into the rotor with a seal/race driver. Pack the new bearings. Install inner bearing into rotor. Install new grease seal. Wipe old grease off of the spindle and apply a thin coat of new great. Install rotor ono spindle. Install outer bearing, washer, and nut. Tighten nut snug then back off nut a half of turn and then tighten agin just barely snug. Install castellated nut and cotter pin. Reinstall dust cap Reinstall caliper and your done. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Jan 15, 2012 | 2005 Dodge Ram 3500

1 Answer

How to change back hub on 97 cr-v


Rear Brake Discs
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-1.1-800x800.jpg Replace the bearing and race as a single set. automotive roller bearing. image by Tom Oliveira from Fotolia.com

    Before raising the rear of your Honda, remove the dust cup from the center of the brake drums using a hammer and chisel. This will give you access to the spindle nut, which you can loosen using an axle nut socket. Then you can raise and remove the wheel/tire assembly ,or assemblies if you are replacing the bearings on both wheels.

    If your Honda model is equipped with rear disc brakes, remove the brake disc retaining screws, the brake hose bracket from the steering knuckle and caliper bracket mounting bolts. Hang the caliper to the coil spring using wire. Do not let the caliper hang free or the brake hose may be damaged.

    At this point, you will be able to remove the brake disc by hand. However, rust may have a firm grip on the disc. If this is the case, use a couple of 8-by-1.25 mm bolts and screw them evenly into the brake disc threaded holes. This will push the disc off the hub. Now you can finish removing the spindle nut and hub/wheel bearing assembly and install the new hub/wheel bearing assembly using a new spindle nut



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WDRoqv Rear Brake Drums
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-2.1-800x800.jpg Pack the bearing with bearing grease before installation. roller bearing image by Tom Oliveira from Fotolia.com

    If your Honda Civic comes equipped with rear brake drums, remove the center grease cup and loosen the axle spindle nut using an axle nut socket. After raising and removing the wheel/tire assembly, finish removing the axle nut and washer.

    You might be able to remove the outer wheel bearing from the spindle using a screwdriver. If not, wiggle the brake drum as you pull on it to let the bearing fall off the spindle. However, the brake drum might be caught in place by the brake shoes. In this case, you can retract the brake shoes through the hole in the back of the backing plate.

    Remove the rubber plug from the back of the backing plate. Then rotate the star wheel on the adjusting screw using a brake adjusting tool as you push the lever off the start wheel with a screwdriver. With the brake shoes off the brake drum, pull the brake drum off the wheel assembly. Then clean the brake assembly with brake parts cleaner and a clean, lint-free towel.

    Now you can set the brake drum on a workbench or hard surface and remove the grease seal and inner wheel bearing. The inner and outer wheel-bearing races can be removed using a drift punch and hammer. Pack the new wheel bearings with high-temperature wheel-bearing grease using a wheel-bearing packer and use a new grease seal during installation. Also, before reinstalling the brake drum, apply a thick coat of wheel-bearing grease to the cavity inside the hub, but do not fill it completely.



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WN9eBb

Aug 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

I need a diagram on f250 hd 4x4 front wheel bearing to replace them


1 Jack the front of the vehicle up and support with jack stands. Remove the front tires and the front brake calipers. Hang the calipers up or support them so they are not hanging by the brake hose, which could damage the hose.

2 Remove the caliper support, then remove the center bearing cover using the hammer and chisel. Tap it out easily so as not to bend it. Remove the cotter pin in the spindle.

3 Remove the large bearing retaining nut and grab the rotor with your hand and rock it forward just enough for the front bearing to fall out.

4 Put the large bearing retaining nut back on, but do not turn more than four or five threads. Grab the rotor with both hands at the 3 o'clock and the 9 o'clock position and pushing down slightly, pull the rotor off swiftly. This will remove the rear bearing and seal at the same time. The retaining nut will knock the bearing and seal out as you pull the rotor off. Remove the retaining nut.

5 Remove the inner races for the bearings using the hammer and chisel. Put the chisel on the top of the bearing race and hammer it down toward the floor and then turn the rotor over and do the other side the same way.

6 Install the new bearing races using the old races as a buffer or an installing tool. Lay the new race in the rotor and line it up to the recession and lay the old race upside down on the new one. Hit the old bearing with the hammer to drive the new bearing into the recess. Make sure you drive the new bearing all the way into its recess. Do the same for the other side.

7 Fill the palm of your hand with grease and push one bearing at a time into the grease and drag it across the hand so that the bearings get a full packing of grease. Install the large bearing first by dropping the bearing into it's race and then installing the seal with the hammer.

8 Install the rotor back onto spindle and hold it in place. While holding the rotor on the spindle with one hand install the front small wheel bearing followed by the large washer and the retaining nut. Tighten the retaining nut (use the crescent wrench) just enough so that there is no play felt. Tighten the nut another 90 degrees with the wrench and then rotate the rotor a couple of times. Back the nut off until it is loose then tighten just until you feel the friction of it tightening up again and stop right there. The bearing must be tight enough that there is no freeplay, but not so tight that the bearings will seize up when they heat up and expand.

9 Install the cotter pin and the bearing cup. Install the caliper support and the caliper. Do the other side the same way then install the tires.

Jul 02, 2011 | Ford F-250 Cars & Trucks

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

3 Answers

How do u change the rear bearings?


Hello Friend:

#1) Raise Car in The Rear Support it Good on Jack Stands.

#2) Remove your Wheel or Wheels if Doing Both Sides.

#3) Now Right in The Center of Your HUB you'll see a Dome Cap Remove the Cap,Now Remove the Cotter Pin, then the Spindle Nut and Washer.

#4) Now you'll pull your Hub Assembly Off ,The Outside Bearing will more or Less Fall off the Hub.But you'll need to Remove the Outer Bearing Race Its the Metal Angled Race.

#5) Before you remove the Outer Race take a Seal Remover and Remove The Grease Seal on the Inside of Hub.

#6) Now the Inner Bearing Will Come Out.You NOW Can Remove Innner and Outer Races.Use a Puch and Hammer Lightly Tap it by Working your Punch Side to Side.

#7) Now You've Remove BOTH inner and Outer Bearing Assemblies.

#8) Before you Start to Install New Races ,Get some Brake Clean and Clean The Inner Hub and the Spindle Good.

#9) Use a Bearing Race Installer Tool to Tap your New Bearing Races in.NOTE: you Don't want to Scar the Beveled Part of the Race Cause thars Where your Bearings Rotate.

#9) Races are in : Now take a Wheel Bearing Packer if you have 1 Availible: If not Pack As Much Heavy Duty Hi Temp Bearing Grease Into the Bearings. And Put some on the Spindle Were your Bearing Run on.

#10) Now Using a Seal Installer Tap your Inner Grease Seal into the Inner Hub Housing.

#11) OK Now your Ready to Put Your Hub Back on:Note: Put a Little Grease in The Domed Cap after you've Got the Hub On.

#12) DON"TS Get Grease on your Brakes or anywhere in The Brake Pad Assembly. #2) Don't Use the OLD Cotter Pin Get a New One. :#3) When Adjusting your Spindle Nut Don't Under Tighten or Over Tighten==Just Snug it down where theres no Play when you Take your Hands 1-Top=1 Bottom and Make Sure theres No Play.

Rotate The Hub During And When Tightening your Spindle Nut.

Put Hub Grease Cap on and Whell or Wheels and you Should be Good to Go.

Thanks for Using Fixya Please let me Know the Quality of my Advice/Solution by Voting Thank You From: d_hubbs

Jul 23, 2010 | 1993 Mercury Topaz

1 Answer

Remove rear wheel bearing


remove wheel, remove brake drum if equipt if not the rotor. remove center nut spindle, then pull the whole thing out. you have to press out the outer race of the bearing from the hub.

Nov 23, 2009 | 1998 Dodge Caravan

1 Answer

I can't find any illustrations on tie rod ends or how to change the wheel bearings


tie rod ends you count the number of turns exposed and run the same number of turns on the new one after you install it. You can rap the side of the rod end with a hammer to break it loose, whack it!
Wheel bearings on the front you remove the wheels, remove the center cap on the hub, remove the cotter pin, then nut and washer, hub assembley will come off. Clean the spindle of old grease, remove the bearings, drive out and replace the old bearing races in the hub, install new races (cups) pack bearings in your clean hands with correct grease, install the bearings, install the washer, nut, tighten then back off a hair until you align the cotter pin hole. Do NOT overtighten, the bearings and races will be damaged! You snug the bearings to "seat them" then back off just enough that the wheels spin freely with no side to side play with the wheels installed to the hub. In other words grab the tires at the top and bottom and see if you have any movement toward the spindle or axle. Rear bearings are done the same way.

Sep 20, 2009 | 1994 Geo Metro

1 Answer

How do you change rear bearing on axle


1. first you must take off the wheels.
2. Now remove the caliper and then slide off the rotor.
3. remove the cotter pin on the hub and the lock collar then with a impact remove the 36mm nut on the shaft.
4. there are 4 bolts on the rear of the hub. rotate the axles so that you can remove them.
5. once these are removed, grab the spindle and shake it loose off the splines.
6. the tuff part is pressing the bearings off the spindle. I used a hydralic press to do it. the only pain was that the inside race of the bearing wouldnt come off so I had to cut it off.
7. now press it all back together. make sure it is all the way to the stop
of the spindle.
8. reinstall it back to the hub, those 4 bolts, not forgetting to clean off splines.
9. Now the spindle nut must be torqued down to at least 206 ftlbs and no more than 276 ftlbs. after that is down add the lock collar and install a NEW cotter pin.
10. reinstall rotor and caliper and wheel.

hope it helps-

Aug 16, 2009 | 1987 Nissan 300ZX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...