Can anyone tell me where the camshaft positioning sensor is located on my 2001 chrysler sebring 2.7 v6

camshaft position Sensor location???

Isuzu SUV Forum https://www.planetisuzoo.com > threads > camshaft-po...
Jun 23, 2009 - It is located on the inside surface of the front of right cyl head. 2000 Rodeo LS (stock). 78 T/A (far ...

SOLVED: Where to locate the camshaft sensor on a isuzu

Fixya https://www.fixya.com > ... > Isuzu > Rodeo
1 answer
It's on the inside of the cylinder head at the rear of the engine. Will be hard to see it because the intake plenum hides it. where to locate the camshaft ...
Doesn't include: LS ‎' Must include: LS

Where is the camshaft position sensor in my 2002 Isuzu ...

JustAnswer https://www.justanswer.com > Car Questions
May 13, 2020 - My son is a mechanic and the Haynes manual says it's under the lower intake. Need to verify. Share this conversation.
1 answer · Top answer: you are welcome

• 
  

  Isuzu Rodeo: WHERE IS AND HOW TO MEASURE THE ...

  https://www.justanswer.com > Car Questions
  Mar 30, 2013 - If you are just testing the sensor, you can check the cam sensor signal at the ECM on pin 11 of connector number 2. It is the same blue wire.
  
  ..

Error code P1340 on a 2001 Isuzu Rodeo with a 3.2 V6 engine refers to "Camshaft Position Sensor Circuit Malfunction." This means that there is a problem with the circuit that reads the position of the camshaft, which can cause issues with engine timing and performance. It is recommended to have a certified mechanic diagnose and repair the issue to ensure proper functionality of the engine.

It depends on what engine you have in the truck. The camshaft position sensor is located either in the distributor(for the 4.3L V6), or on the top rear of the engine(4.8L, 5.3L, 6.0L)

They are located on each head if im not mistaken on the corner near the air intake boot that goes to air filter. The cylinder head close to the radiator is 2 4 6.

camshaft position sensor is at the back end of the camshaft. should be just across from the battery.

Disconnect negative battery cable. Remove power ste
ering pump. Remove camshaft position sensor mountin
g
bolt and remove camshaft position sensor. To instal
l, reverse removal procedure. Tighten camshaft posi
tion
sensor bolt to specification.

P0340 OBD-II Trouble Code
Technical Description
Camshaft Position Sensor Circuit Malfunction

What does that mean? This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms
Symptoms can include:

• Hard starting or no start
• Rough running / misfiring
• Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:

• a wire or connector in the circuit could be grounded/shorted/broken
• the camshaft position sensor may have failed
• the PCM may have failed
• there exists an open circuit
• the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

• Visually inspect all the wiring and connectors in the circuit
• Check for continuity in the circuit wiring
• Check the operation (voltage) of the camshaft position sensor
• Replace the camshaft position sensor as required
• Check the crankshaft position circuit as well
• Replace circuit wiring and/or connectors as required
• Diagnose/replace the PCM as required

Also, the cams/crank are out of alignment, thats why you are getting a cam position code (P0340). For more details about your model, you can visit autozone.com (free register)

Hope helped whit this (remember rated this help) Good luck.

CAMSHAFT POSITION SENSOR 2001 Dodge Truck RAM 1500 1/2 ton 2WD 5.9L SFI 8cyl The Camshaft Position Sensor is located: Under hood, center, upper engine area, rear of intake manifold, mounted in distributor

If this is helpful.Please leave ositive Feedback. Thanks, SnugglePants

The crank sensor is in the top of bell housing of the transmission towards the back of the engine compartment. The cam sensor is built into the distributor.

The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.