Question about Isuzu Pickup

1 Answer

Hydraulic clutch slave cylinder

The petal in my 1990 isuzu pickup truck stuck to the floor the other day and would not go back into gear. Is this a bad clutch, throw out bearing, master,slave cylinder?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 5,332 Answers

This symptom would typically be solved with a new cluth slave cylinder. Check to make sure the fluid is full in the master cylinder reservoir. If the fluid is empty then there is either a leak, or the clutch is has worn. filling the reservoir and bleeding the system may get you back on the road.

Posted on Apr 30, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: new clutch not working properly really could use some help

My best guess on this, assuming that the clutch master is working and it has no air remaining in the system is that you either have the wrong throwout bearing in there or that it is installed incorrectly. Also, rare but can happen is that if the pressure plate assembly is a rebuilt one, the face has been cut too far and clearances are off.
Obviously, check everything external before taking it apart again, but that's where I think you will need to go.

Posted on Nov 18, 2009

Testimonial: "thanks did have some issues installing throw out bearing so maybe that is my problem"

  • 157 Answers

SOURCE: Clutch pedal does not disengage clutch

If the car hasn't been driven for a while it could be corrosion on the fork but I think that is unlikely. I think you are right about the release bearing being jammed in the spring. If the truck has quite high mileage, it probably means a clutch job.

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding clutch


Are you sure the clutch disc and fork are connected to the slave cylinder ?

Apr 29, 2013 | 1997 Isuzu Rodeo

1 Answer

1988 chevy k2500 clutch pedal has no resistance


Your truck has a hydraulic clutch release system, you have a problem in it due to a leak in the slave or the master cylinder, The slave cylinder which is the one that leaks most often is inside the bell housing and it requires the ****** be removed to replace it.

Aug 09, 2012 | Cars & Trucks

2 Answers

When clutch is let out all the way, truck will barely move, why?


clutch wear,, it should catch an inch or so from the floor, if not, try to adjust the cable, if that doesn't help its time for a new disc at min. clutches are just like brakes, they wear out

Apr 26, 2011 | 1990 Isuzu Pickup

2 Answers

I have a 2000 Isuzu Rodeo in which the clutch pedal went to the floor & stayed there. Upon inspection, the clutch master cylinder was empty on fluid. I filled the reservoir & bleed the clutch...


It sounds as if you have 2 problems here.

The fact that the clutch pedal went to the floor and stayed there suggest a fault in the master cylinder. It may be that you need to overhaul the master cylinder.

Overhaul kits are available at less cost than a clutch master cylinder:
0results for isuzu rodeo clutch master cylinder overhaul kit

The grinding noise ... A grinding noise would be caused by either the gear not engaging properly because of the defective clutch.

Or, if it is more of a squealing noise - that may be the clutch release bearing at fault.

Are you absolutely sure that your entire clutch unit - pressure plate, driven plate and release bearing aren't worn?
116results for isuzu rodeo clutch

Mar 14, 2017 | 2000 Isuzu Rodeo

2 Answers

Clutch go's all the way to floor with no resistents can not shift gears engine won't stay on. 1987 5 speed pickup truck


Sounds like the hydraulic fluid may have leaked out of a line or the slave cylinder is leaking, or the master clutch cylinder has an internal leak that doesn't actuate the clutch effectively when the pedal is pushed to the floor.

Oct 28, 2010 | 1987 Nissan Pickup

2 Answers

My 87 sami has been parked in the barn for about 3 years without moving. i fired her up the other day, and noticed, that will idleing, i could not put the trans into any gears. when i turned the engine...


the slave cylinder for the clutch has lost pressure or has gone bad, don't panic!! not yet, pump the clutch about a hundred times, i'm not kiddin! sometimes it happens,you have a hydraulic slave cylinder clutch. they loose pressure if not used often, after you've pumped it 29times look under the driverside door towards motor to see if fluid is dripping down,, if not,, keep pumping until the clutch comes up;;;FEEL PRESSURE WHEN YOU'RE PUSHING CLUTCH IN hope this helps!!

Oct 07, 2010 | 1986 Suzuki Samurai

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

1 Answer

Where is slave cylinder for clutch on 1994 Isuzu pickup 2.3 litre


To determine which type of clutch you have, servo hydraulic or cable.
Look down past the engine bell housing and determine the existance of a hydraulic clutch slave cylinder.(a piece of casting with a rod facing towards the rear of the vehicle pocket into a bracket protruding out of the gearbox bell housing. As well as a pipe and bleed nipple to be crude)
(which I believe you have).The hydraulic fluid for this unit is sourced from the brake master cylinder reservoir via a sneaky pipe partially obscured to the clutch master cylinder on the internal firewall.If you have no clutch slave cylinder near the bell housing there would be an obvious bounden cable running from the firewall down to the outer of which will be stopped at a bracket hanging off the engine.The inner will continue to a bracket protruding from the gearbox bell housing.

Mar 04, 2009 | 1994 Isuzu Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...