Question about 2005 Renault 181

Open Question

2001 1.4 Renault Clio fuel tank leaking by fuel pump housing

Does any one have a diagram of how to fit the fuel pump housing in the tank so that it seals properly? Thanks in advance.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22246 Answers

SOURCE: renault clio 2ltr sport back brakes

two brake shoes with a auto adjuster at the top ,handbrake lever on right shoe and two return springs .if you cant remember take the other side off and look at that

Posted on Feb 28, 2009

Ad
reunic
  • 15 Answers

SOURCE: my renault clio dipped beam light are not nworking

itll be the light arm there allways going yes the swich has gon thanks ben

Posted on Nov 16, 2009

  • 127 Answers

SOURCE: RENAULT CLIO 8 VALVE TIMING BELT SNAPPED WHERE DO

hallo
first let me know year, engine code (or at least typ of engine 1.2, 1.4...). and I will send you picture for timing belt.
and it will (did) bend valves, so you`ll have to remove cilinder head *** well.

Marko

Posted on Nov 21, 2009

  • 566 Answers

SOURCE: how do you get on a fan belt on a renault clio 99

hi from uk unfortunately your assumption is correct! you do have to 1st remove the p/steerpump belt to be able to change/renew the alternator belt not too difficult just a little patience needed and a few bandaids/plasters ? for the scratches on hands if you have large ones as i do ?

Posted on Dec 08, 2009

sandman357
  • 236 Answers

SOURCE: WHERE IS THE FUEL PUMP LOCATED IN THE RENAULT CLIO

most fuel pumps if not all are inside the fuel tank. to replace it check in your trunk if you have access through there or under your back seat. most likely you'll have to drop the tank

Posted on Mar 07, 2010

Testimonial: "thanks for your advise , i found it in the tank "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Leaking fuel pump


If the fuel is leaking into the car you will need the replace the seal on the top on the pump assembly not the seals on the pump itself but before changing the seal just double check the fuel lines are tight and the leak is actually from the fuel splashing out of the tank. The seal your after is referred to as the pump assembly oring ( big rubber oring around the top of the assembly a smear of silcone can be used as a temporary fix but erge you to get it fix properly as soon as possible and fuel fumes in the cabin can be extremely deadly)
Hope this helps

Jan 15, 2014 | 2003 Nissan Altima

2 Answers

When pumping gas in a 2000 hyundai it the nozzle keeps cutting off . it take forever to fill the gas tank up


i`m guessing that you have tried to install the nozzle in different places in the filler neck while filling the car.if this you have tried then you may have a bad vent valve that is not working properly causing excess air pressure in the fuel tank shutting off the nozzle.have a shop check this out for you.

Sep 16, 2011 | Hyundai Accent Cars & Trucks

2 Answers

Where is fuel pump for 1996 mercury mystique located on the car and how do you remove it


SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B
Removal
  1. Depressurize fuel system as outlined in Service Procedures- Fuel System Pressure Relief.
  1. Remove rear seat cushion. Refer to Section 01-10.
  1. Remove plastic grommet from floor pan.
  1. Disconnect fuel pump module electrical connector.
  1. NOTE: To disconnect fuel tubes from fuel pump module, compress tabs on both sides of each nylon push connect fitting and ease fuel tube out of fuel pump module.

    Disconnect fuel and vapor return tubes from fuel pump module.
  1. Turn fuel pump locking retainer ring counterclockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent and remove fuel pump locking retainer ring.
  1. NOTE: After fuel pump module removal, immediately cover fuel pump module opening in fuel tank in order to prevent fuel system contamination.

    Remove fuel pump module and cover fuel pump module opening in fuel tank.
  1. Remove fuel pump module O-ring seal and discard.
Installation
  1. NOTE: When cleaning fuel pump module mounting surface on fuel tank, use caution to prevent any foreign material from entering fuel system.

    Clean fuel pump module mounting flange and fuel pump module mounting surface and O-ring seal groove on fuel tank.
  1. Apply a light coat of Premium Long-Life Grease XG-1-C, -K or equivalent meeting Ford specification ESA-M1C75-B on a new O-ring seal to hold it in place and install it into the O-ring seal groove on the fuel tank.
  1. Install fuel pump module carefully to ensure that filter is not damaged. Make sure that locating keys are in keyways and O-ring seal remains in place.
  1. Hold fuel pump module in place and install fuel pump locking retainer ring finger-tight. Make sure that all locking tabs are under fuel tank lock ring tabs.
  1. Secure fuel pump locking retainer ring by rotating clockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent until fuel pump locking retainer ring rests against stops.
  1. Connect fuel and vapor return tubes to fuel pump module.
  1. Connect fuel pump module electrical connector.
  1. Install plastic grommet in floor pan.
  1. Install rear seat cushion. Refer to Section 01-10.
  1. Install Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B as outlined in Service Procedures-Fuel System Pressure Relief.
  1. Turn ignition switch to RUN position for three seconds repeatedly (5 to 10 times) until pressure gauge reads at least 270 kPa (30 psi). Check for leaks at fittings.
  1. Remove pressure gauge, start engine and recheck for leaks.
Hope this helps

Aug 13, 2011 | 1996 Mercury Mystique

1 Answer

I need to replace the fuel pump on my 2001 Saturn L200 with a 2.2 L Engine. What is the best procedure?


Fuel Pump REMOVAL & INSTALLATION 1.9L Engine To prevent excessive fuel spillage, whenever the tank is removed from the vehicle it should be no more than 1?2 full. Removal of the fuel pump module assembly requires the removal of the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel feed and return lines from the filter/pressure regulator
    • Fuel pump vapor line from the fuel tank vent pipe
    • Fuel pump module retaining ring with service tool SA9156E. A 1?2 inch breaker bar will loosen the lockring
    NOTE: To prevent bending of the sending unit float arm, lift the pump module up slightly to disengage the orientation tabs in the tank. Rotate the module 90 degrees clockwise until the fuel lines are facing the 1 o'clock position.
    • Fuel pump module from the fuel tank until the bottom of the pump module is close to the fuel tank opening
    • Tilt the pump module approximately 45 degrees to the right hand side of the tank and lift the pump from the fuel tank
    • Fuel pump to tank seal and discard it
    To install:
  4. Install or connect the following:
    • Fuel pump module into the fuel tank by orientating the float to face the right side and tilting the module approximately 45 degrees
    • Fuel pump into the tank and rotate the assembly 90 degrees counterclockwise to align the module tabs with the slots in the tank
    NOTE: The fuel pump retaining ring cannot be properly installed if the flange locator tabs are not aligned with the slots in the fuel tank.
    • Retaining lockring with tool SA9156E
    • Vapor line to the fuel tank vent pipe
    • Fuel feed and return lines to the filter/pressure regulator
    • Fuel feed, return and EVAP canister purge line in the fuel tank retaining clip
    • Fuel tank
    • Negative battery cable
  5. Start the vehicle and check for leaks, repair if necessary.
2.2L and 3.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel tank
    • Fuel lines from the fuel pump module cover
    • Fuel pump module retaining ring with a Sending Unit Wrench, J43827
    • Pull the retaining clip toward the float arm and lift up
    • Fuel pump straight up from the fuel tank
    • Fuel pump tank seal and discard the seal
    • Fuel feed line from the bottom of the fuel pump cover with Clamp Pliers J43914
    • Fuel pump electrical connector Fig. 1: Remove the fuel pump cover lockring-2.2L and 3.0L engines 9306zg57.gif
    To install:
  4. Install or connect the following:
    • Fuel pump feed line to the cover
    • Fuel pump electrical connector
    • Fuel pump to the new seal
    • Fuel pump cover lockring with tool J-43827
    • Fuel lines and wiring harness
    • Fuel tank
    • Negative battery cable
  5. Start the vehicle and check for leaks, repair if necessary.
prev.gif next.gif

Jan 29, 2011 | 2001 Saturn L-Series

1 Answer

How do you change the fuel pump?


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Rear seat cushion
    • Plastic access panel
    • Fuel pump wiring harness connector
    • Fuel lines
      7922jg34.gif

      View of fuel pump fittings through the floor pan
      Click to Enlarge 7922jg35.gif

      Remove the locking ring from the fuel pump sender with special tool Fuel Tank Sender Wrench D84P-9275-A
      Click to Enlarge

    • Fuel pump module lock ring. Use special tool Fuel Tank Sender Wrench D84P-9275-A.
    • Fuel pump module

To install:

  1. Install or connect the following:
    • Fuel pump module with a new O-ring seal
    • Fuel pump module lock ring using special tool Fuel Tank Sender Wrench D84P-9275-A
    • Fuel lines
    • Fuel pump wiring harness connector
    • Plastic access panel
    • Rear seat cushion
    • Negative battery cable
  2. Start the engine and check for leaks and proper operation.
shinehutt_37.gif

hope this helps plz vote comment reply if need more help

Jan 17, 2011 | 2002 Mercury Cougar

2 Answers

I had a new fuel pump installed in my aveo and a seal wasnt put in place so my car reeked of gas. Now we pulled the fuel pump back out and there is an orange gasket dangling off the fuel pump. I was...


do both,that way you know its fitted properly
(have you tried lighting a cigarette, sat inside the car with all them fumes,,,,,cars do fly......)

Jun 26, 2010 | 2004 Chevrolet Aveo

1 Answer

Where is the access panel for the fuel pump


There is no access panel for the fuel pump- You have to drop the tank to get at it!

1. Syphon any gas from the tank

2. Prop the gas tank with a support

3. Loosen the tank straps and fill hose strap then disconnect the straps on one side

3. Drop the tank

4. Disconnect the fuel lines and wiring harness

5. Pull the tank from under the vehicle, turn the pump seal counter clockwise then remove the pump- Careful not to damage the O-ring gasket as you may need to use it again because the new gasket may not fit properly

Install in reverse order

Apr 05, 2010 | 2004 Chrysler PT Cruiser

1 Answer

How to do i change the fule pump on a 2006 ford fusion 3.0..car starts but seems to starve for fuel..right after filling tank up I drove and stopped at a light car sputtered,i pushed the pedal to the floor...


ani_caut.gif WARNING: Do not carry personal electronic devices such as cell phones, pagers or audio equipment of any type when working on or near any fuel-related components. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions can result in personal injury. ani_caut.gif WARNING: Fuel in the fuel system remains under high pressure even when the engine is not running. Before repairing or disconnecting any of the fuel system components, the fuel system pressure must be relieved to prevent accidental spraying of fuel causing personal injury or a fire hazard.
  1. Release the fuel system pressure. For additional information, refer to Section 310-00.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Release the fuel tank filler cap and position it aside.
  1. ani_caut.gif CAUTION: Upon removing the special tool, the fitting on the end of the hose can become detained by the one way flapper valve. Carefully remove the hose using a gentle agitating motion to avoid detaching the hose from the fitting.
    NOTE: The special tool must be inserted into the fuel tank filler pipe until the fitting on the end of the hose enters into the fuel tank spout, opening the one way flapper valve.
    Insert the special tool into the fuel tank filler pipe.
    n0060483.gif
  1. NOTE: This step will remove approximately 1/8 tank of the fuel from a completely full fuel tank and the majority of any residual fuel in the fuel tank filler pipe.
    Attach the fuel storage tanker to the special tool and remove as much fuel as possible from the fuel tank and fuel tank filler pipe.
  1. Remove the rear seat lower cushion. For additional information, refer to Section 501-10.
  1. Position the carpet and/or any insulation covering the fuel pump module access cover.
  1. Remove the 4 screws and the fuel pump module access cover.
    n0043014.gif
  1. Disconnect the fuel pump module electrical connector.
  1. Disconnect the fuel supply tube-to-fuel pump module quick connect coupling. For additional information, refer to Section 310-00.
  1. Using the special tool, remove the fuel pump module lock ring retainer.
    n0043328.gif
  1. ani_caut.gif CAUTION: The fuel pump module must be handled carefully to avoid damage to the float arm.
    ani_caut.gif CAUTION: Place absorbent pads on the floor pan in the immediate area in case of fuel spills. Carefully remove the fuel pump module from the vehicle to avoid fuel spillage inside the vehicle.
    ani_caut.gif CAUTION: The fuel pump module will have residual fuel remaining internally, drain into a suitable container
    Completely remove the fuel pump module from the fuel tank.
  1. ani_caut.gif CAUTION: Inspect the mating surfaces of the fuel pump module flange and the fuel tank O-ring seal contact surfaces. Do not polish or adjust the O-ring seal contact area of the fuel tank flange or the fuel tank. Install a new fuel pump module or fuel tank if the O-ring seal contact area is bent, scratched or corroded.
    ani_caut.gif CAUTION: Make sure to install a new fuel pump module O-ring seal. Install a new lock ring if it is bent, damaged or corroded.
    NOTE: To install, apply clean engine oil to the O-ring seal.
    Remove the fuel pump module O-ring seal.
  1. To install, reverse the removal procedure.
    • Make sure the alignment tab on the fuel pump module and the fuel tank meet before tightening the fuel pump module lock ring.

2010&c18=modelyear&c20=n943901&c35=wsm%2cfuel%20pump%20module%2cs6s%2c310-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 03, 2010 | 2006 Ford Focus

2 Answers

WHERE IS THE FUEL PUMP ON A 1994 TOYOTA CAMRY


Fuel pump is located inside the fuel tank and is attached to the sending unit. Do not smoke or have any open flame in the work area when removing the fuel pump.

REMOVAL OF FUEL PUMP:

  1. Disconnect the negative battery cable.
  2. Relieve fuel pressure
  3. Remove the rear seat cushion.
  4. Remove the floor service hole cover .
  5. Disconnect the electrical fuel pump wiring at the fuel pump assembly. Check for any fuel leakage while in there.
  6. Remove the gas cap, this will prevent any fuel gas spilling out of any high pressure lines.
  7. Use a fare nut wrench to disconnect the outlet.
  8. Remove the pump bracket attaching screws
  9. Disconnect the return house from the pump brackets, then pull ou the pump/bracket assembly.
  10. Remove the nut and spring washing, then disconnect the wires from teh pump bracket.
  11. Remove the sending unit attaching screws then remove the unit from the bracket.
  12. Pull the lower side of the fuel pump from the bracket.
  13. Unplug the connector to the fuel pump
  14. Disconnect the hose from the pump.
  15. Separate the filter from the pump. Use a small screwdriver to remove the attaching clip.
  16. Inspect all the lines, houses and fittings for any sign of corrosion, wear and damage to the surfaces. Check the pump outlet hole and the filter for restrictions
  17. When reassembling, ALWAYS replace the sealing gasket with a new ones. "Also replace any rubber parts showing any sign of deterioration".

To install:
  1. Install the pump filter using a new clip. Install the rubber cushion under the filter
  2. Connect the outlet hose to the pump and pump bracket.
  3. Engage the connector to the fuel pump. Install the fuel sending unit to the pump bracket. The remainder of the installation is the reverse of the removal.
  4. Start the engine and check carefully for any sign of leakage around the tank and lines. Road test the vehicle for proper operation.

Dec 15, 2009 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

xxxxxx xxx

Level 3 Expert

4874 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...