Question about Subaru Cars & Trucks

Open Question

P2270 p2271 Where is the circuit bank 1 and sensor 2 located

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 279 Answers

SOURCE: 01 Eclipse GT - bad o2 sensor heater circuit (bank 1 sensor 2)

Your question was truncated. I see that the bad sensor is on bank 1, but I can not see if it is the upstream (sensor 1) or downstream (sensor 2) sensor. The upstream sensors are mounted in the exhaust manifolds (look sort of like spark plugs) and have wires going to them.
You will need a 7/8" or 22mm wrench to remove the sensor (after disconnecting the wires). If your car has over 70,000 miles I STRONGLY suggest that you replace BOTH upstream sensors. One in each exhaust manifold.
Charlie

Posted on Dec 23, 2008

Ad
dttech
  • 4803 Answers

SOURCE: where is the bank 2 sensor 1 located.

Oxygen sensors are always numbered like this:

Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Most GM engines have #1 cylinder located on the left bank, (or Driver's Side) of the engine,

So, the answer to your question would be that you are looking for the sensor located before the catalytic converter on the right (or Passenger Side) of the truck.

Posted on Oct 17, 2009

bschilz
  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

7acfed1.gif
d9eb1af.gif

Posted on Oct 20, 2009

roniecon
  • 6927 Answers

SOURCE: were bank 1 sensor 2 located on a 1997 tahoe

bank 1 is the drivers side,and it is the down stream sensor,the one after the cat,converter,If this was helpful,please let us know,thank you.

Posted on Jan 03, 2010

emissionwiz
  • 77544 Answers

SOURCE: where are bank 1 sensor 1, bank 2 sensor 1, bank 1

bank one sensor 1 is the bank of cylinders that number 1 spark plug is located in, bank 2 the other side, this assumes u have a V8, the sensor one location is the sensors that are BEFORE THE CATALYTIC CONVERTER, the sensors referred to as sensor 2 are after the ones AFTER THE CATALYTIC CONVERTER IN THE EXHAUST SYSTEM.

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2008 Silverado is throwing codes p2271,p2272 and p2273. What is the possible cause?


P2271 CHEVROLET - HO2S Signal Stuck Rich Bank 1 Sensor 2
https://www.autocodes.com/p2271_chevrolet.html

P2272 - O2 Sensor Signal Biased/Stuck Lean Bank 2 Sensor 2
https://www.autocodes.com/p2272.html

P2273 - O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 2
https://www.autocodes.com/p2273.html

Jan 27, 2017 | 2008 Chevrolet Silverado

1 Answer

Codes P2270& P2272 after oil change check engine light on drove under 100 miles both O2 sensors bad .Could shop have caused this somehow??? Maybe banging them or something ?


make sure they are plugged in tight Definition of Diagnostic Trouble Code P2270 Category: Powertrain Definition: O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 2Note: This definition of P2270 is applied to all manufacturers

P2270 - O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 2 Comments ' Add Yours
Possible causes
- Faulty Rear Heated Oxygen Sensor Bank 1
- Rear Heated Oxygen Sensor Bank 1 harness is open or shorted
- Rear Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Exhaust gas leaks Help with this
When is the code detected?
The Powertrain Control Module (PCM) detected the HO2S12 sensor has reported a lean condition for an extended period during an intrusive test
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- High Fuel Consumption
- Excessive Smoke from Exhaust
P2270 Description
The Powertrain Control Module (PCM) supplies a voltage of about 450 mV between the HO2S high and low signal circuits. The oxygen sensor varies the voltage over a range from about 1,000 mV when the exhaust is rich, down through about 10 mV when the exhaust is lean.
The PCM monitors and stores the heated oxygen sensor (HO2S) voltage information. The PCMevaluates the HO2S voltage samples in order to determine the amount of time the HO2S voltage was out of range. The PCM compares the stored HO2S voltage samples taken within each sample period and determines if majority of the samples are out of the operating range.

Definition of Diagnostic Trouble Code P2272 Category: Powertrain Definition: O2 Sensor Signal Biased/Stuck Lean Bank 2 Sensor 2Note: This definition of P2272 is applied to all manufacturers

P2272 - O2 Sensor Signal Biased/Stuck Lean Bank 2 Sensor 2
' Add Comment
Possible causes
- Faulty Rear Heated Oxygen Sensor Bank 2
- Rear Heated Oxygen Sensor Bank 2 harness is open or shorted
- Rear Heated Oxygen Sensor Bank 2 circuit poor electrical connection
- Exhaust gas leaks
What does this mean?
When is the code detected?
The Powertrain Control Module (PCM) detected the HO2S22 sensor has reported a lean condition for an extended period during an intrusive test
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- High Fuel Consumption
- Excessive Smoke from Exhaust
P2272 Description
The Powertrain Control Module (PCM) supplies a voltage of about 450 mV between the HO2S high and low signal circuits. The oxygen sensor varies the voltage over a range from about 1,000 mV when the exhaust is rich, down through about 10 mV when the exhaust is lean.
The PCM monitors and stores the heated oxygen sensor (HO2S) voltage information. The PCMevaluates the HO2S voltage samples in order to determine the amount of time the HO2S voltage was out of range. The PCM compares the stored HO2S voltage samples taken within each sample period and determines if majority of the samples are out of the operating range.
P2272 Information for specific makes
P2272 BMW
P2272 DODGE
P2272 FORD

Jul 30, 2015 | Cars & Trucks

1 Answer

Check engine light is on autozone gave P2270 after checking it? What does this mean?


This P2270 trouble code refers to the post-catalytic converter O2 (oxygen) sensor on bank #1, sensor #2.

Check this site:
P2270 O2 Sensor Signal Stuck Lean B1S2

P2270 O2 Sensor Signal Stuck Lean B1S2

Feb 28, 2015 | Cars & Trucks

1 Answer

Code po136 circuit bank 1 senser 2 (seep2270,p2271) on 2002 subaru forester


Possible causes
- Faulty Rear Heated Oxygen Sensor Bank 1
- Rear Heated Oxygen Sensor Bank 1 harness is open or shorted
- Rear Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

Most likely is your rear O2 sensor malfunction.

Sep 27, 2014 | 2002 Subaru Forester

1 Answer

2005 Mazda Tribute P0172 & P2270


Hi Paul, Have you had a fault code relating to the knock sensor? That sensor controls ignition timing which can have a relationship to the fault codes you report? Regards John

Apr 06, 2013 | 2005 Mazda Tribute

1 Answer

07 Kia Spectra Code P2626, P2097, P2271, P0171


P0171 System too Lean (Bank 1)
P2097 Post Catalyst Fuel Trim System Too Rich
P2271 O2 Sensor Signal Stuck Rich
P2626 O2 Sensor Pumping Current Trim Circuit/Open
_____________
FGTech Galletto 2

Jan 26, 2013 | 2007 Kia Spectra LX Sedan

1 Answer

2002 Subaru Forester P0136 see P2270 P2271 intermittent idling fluctuation and acceleration hesitation


Is the wiring good going to the O2 sensors? Maybe just look the car over and see if you have any bad grounds. They can do weird things. Could be a bad ICU.

Jan 22, 2012 | 2002 Subaru Forester

1 Answer

2005 Honda accord code p2270 that is ?


DTC P2270: Rear Secondary HO2S (Bank 1, Sensor 2) Circuit Signal Stuck Lean

Is this the only code that is coming up? If so, replacing the Bank 1 Sensor 2 Oxygen sensor should fix it. If there are any other engine/drivetrain/emissions related codes, I would recommend ignoring this code for now and fix the other things first, then retest the vehicle to see if this code comes back.

For more information about locating oxygen sensors and repairing oxygen sensor codes, please review the following article:

Which Oxygen Sensor Is It?

What Else Could Be Wrong?

Sep 28, 2011 | 2005 Honda Accord

1 Answer

2006 hundai elantra P2270 code. If this is an O2 sensor, which one?


Possible O2 sensors:

P2270 O2 Sensor Signal Stuck Lean Bank 1 Sensor 2
P2271 O2 Sensor Signal Stuck Rich Bank 1 Sensor 2
P2272 O2 Sensor Signal Stuck Lean Bank 2 Sensor 2
P2273 O2 Sensor Signal Stuck Rich Bank 2 Sensor 2
P2274 O2 Sensor Signal Stuck Lean Bank 1 Sensor 3
P2275 O2 Sensor Signal Stuck Rich Bank 1 Sensor 3
P2276 O2 Sensor Signal Stuck Lean Bank 2 Sensor 3
P2277 O2 Sensor Signal Stuck Rich Bank 2 Sensor 3
P2278 O2 Sensor Signals Swapped Bank 1 Sensor 3 / Bank 2 Sensor 3
---
This is Bank 1 (closer to the dash panel) Sensor 2 (located after the catalytic converter).

---
Note: A malfunctioning front oxygen sensor may cause fuel trim codes to set.
  1. Several Diagnostic Trouble Codes use specific terminology to refer to sensor location. The illustration and key below explain the following terms:
  2. Engine BANK Bank 1 is closer to the dash panel, (also referred to as RH or right hand). Bank 2 is closer to the radiator, (also referred to as LH or left hand).
  3. UP Refers to Sensor 1 or "front sensor". It is located closer to the exhaust manifold and before the catalytic converter.
  4. DOWN Refers to Sensor 2 or "rear sensor." It is located after the catalytic converter.
  5. The following examples show how to interpret oxygen sensor terminology:
  6. B1/S1 = Bank 1/Sensor 1 = Dash panel side, BEFORE the catalyst or "upstream"
  7. B2/S2 = Bank 2/Sensor 2 = Radiator side, AFTER the catalyst or "downstream"

Aug 06, 2010 | Hyundai Elantra Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...