Question about Cars & Trucks

Open Question

How to drain the engine coolant from the engine block of a hyundai getz

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 169 Answers

SOURCE: Engine block coolant drain plug

Unfortunately g.m. screwed the knock sensor into the drain port on the block. It is on the rear of the engine between the eng. and the trans.. If you are flushing the system out then just remove the thermostat (also under the car on the bottom of the engine) and flush the system out. anticipate the water left in the system by adding aprox. 1/2 gallon of straight coolant concentrate before adding the 50/50 mix. Good luck ,hope I helped

Posted on Aug 30, 2008

Ad
emissionwiz
  • 76070 Answers

SOURCE: engine block coolant drain plug location

They are on the side of the engine block, there will either be a pipe plug or a sensor in the threaded hole(s)

Posted on Aug 25, 2008

  • 2920 Answers

SOURCE: Draining the Engine Block of Coolant.

the drain plug is under the front of the truck on the drivers side back of the radiator. you have to turn it to open it .

Posted on Mar 01, 2009

  • 102 Answers

SOURCE: hyundai getz 1.1 2004 engine sluggish whenpulling

thats sounds like the most likely culprit, collapsed cat. or collapsed muffler.. not cheap to replace. but has to be done.

Posted on Nov 15, 2009

budgie140
  • 501 Answers

SOURCE: need to find engine coolant drain plug

usually on side of block,exhaust side,towards back,brass hexanogal bolt.need hoist to get underneath to find it.

Posted on Jul 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getz 09/04 engine number location


in a silly place
think a getz would be the same
most FWD hyundai
remove any plastics in the line of sight
on the block .below the alternator above the water pump

26329410-3wfjcuwskowboueanthfobid-3-0_0.jpg26329410-3wfjcuwskowboueanthfobid-3-2.gif

Oct 27, 2016 | Hyundai Cars & Trucks

1 Answer

Removal of 2008 hyundai getz engine


Watch the video's on Youtube
DIY Part Hyundai Elantra transmission engine swap 1 of 3 Removing the...


It is not an exact match but the procedure is typical.

Jun 28, 2016 | Hyundai Cars & Trucks

1 Answer

Hyundai getz starting problem


If the battery is exhausted, four years is a good age, then yes, the engine will have difficulty turning against compression.

Jun 16, 2017 | 2007 Hyundai Getz 1.6

1 Answer

Hyundai getz 2004


Check coolant in radiator. If it is low check for loose hoses on heater unit in car. Check that the ac unit drain is not blocked as it may not be coolant but water condensation from the ac unit not being able to drain outside

May 04, 2013 | Cars & Trucks

1 Answer

How can i tell if my wheel bearings need to be replaced without pulling off parts for hyundai getz 2002


Sound comparison.
Jack up one front wheel, and securely block the other 3 wheels. Start the engine and put the car in gear, and let the motor run the wheel .
Do not race the engine.
Listen to the sound it makes.
Now shut off the engine and do the same to the other front wheel.
Is one really noisy ?
That's the problem wheel.
Unless you car was in a flood, wheel bearings usually last a lifetime on most cars.
Be blessed.

Feb 17, 2013 | 2002 Hyundai Getz

1 Answer

Where is the thermostat in a 2007 hyundai getz automatic?


follow top large coolant hose to engine block you should see thermostat housing held in place by three bolts remove housing and you will see thermostat.

Jun 24, 2012 | 2007 Hyundai Getz 1.4

2 Answers

Getz 2007 46000km has like a tappet noise coming from motor car starts and runs well we have only had it 2 weeks and had been looking 4 3 months 4 a car was gonna buy a toyota corolla but chose 2 buy the...


drain the oil flush the engine then put in good grade of oil the tappet is sticking as hyundais have trouble getting oil round the engine this wont stop the problem but will make the noise go away until you can get the tappet replaced

Sep 18, 2011 | Hyundai Accent Cars & Trucks

1 Answer

Old engine smokes, even after service no improvements, Hyundai getz 1.3


Is it using oil, or is coolant going down. Perhaps a compression test ?

Jul 30, 2009 | 2001 Hyundai XG300

1 Answer

Im replacing timing belt, accessory belts and water pump on my hyundai elantra gls 1997 sta wgn auto transmission. (1)Where is bolt to drain engine block coolant?(2)After removing front engine mountin


(1) No need to know if engine block coolant drain plug was available. Once the water pump was removed, all engine block coolant was drained. (2) After removing the three engine mounting bracket bolts, I also removed the mount bracket from the the body and made enough room to replace the timing belt easier.

May 18, 2009 | 1997 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...