Question about Cars & Trucks

Open Question

1990 5th wheel trailer vacationeer sterling model

How to run slide-out and light apliances etc basically everthing

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My jayco fifth wheel trailer slide out does not come out evenly!


Use wheel bearing grease to lube the slides. There is a You Tube video that shows you how to maintain the slide out too.

Oct 01, 2014 | Cars & Trucks

1 Answer

Trailer fuses


Should not be any fuses other than the basic ones for the lights. Check any plug in connectors and make sure you have a good ground wire from trailer to truck.

Mar 25, 2014 | Honda Pilot Cars & Trucks

1 Answer

Where is the brake light switch on a sterling 2005 at 9500


The wire you want to slice into coming up the back of the fuse box for the break light fuse

Mar 14, 2013 | Cars & Trucks

1 Answer

I wired my 2011 Kia Sorento with a converter and 4 wire flat connector for my utility trailer. The wiring confirmed correct by using a circuit tester. There is signal going in and signal coming out of the...


you need a adapter for the flashing lights left and right as well the brake lights are seperate along with parking lights for the electric brakes you have to run a power direct to battery with circuit breaker installed on the line but if you look under the bumper near the drivers side in the back you have a connector installed by the company and you might be able to use it if that is what you did then you have to check the fuses because everthing is installed except the fuse for the connector so if thats what you did check the fuse box for missing fuses or burnt so green wire for right, white ground ,brown parking,yellow left the brake lights go through the adapter so check it out

Mar 22, 2011 | Kia Sorento LX Cars & Trucks

1 Answer

Instructions for wiring a moving trailer connector


accessconnect_logo.jpg


Trailer Wiring Diagrams 4 Way Systems

4 way flat molded connectors allow basic hookup for three lighting functions; right turn signal / stop light (green), left turn signal / stop light (yellow), taillight / license / side marker (brown) and a ground (white).

4%20way%20wiring.jpg 4way_vehicle.jpg 4 way tow vehicle side.
4way_trailer.jpg 4 way trailer side.
5 Way Systems

Same as 4 way system listed above but adds a extra blue wire for brake signal or auxiliary power. Used on pop up camper trailers or utility / boat trailers.
5way_vehicle.jpg 5 way tow vehicle side.
5way_trailer.jpg 5 way trailer side.
6 Way System, Rectangle Plug 3/4 inch by 1 inch 6 way rectangle connectors right turn signal (green), left turn signal (yellow), taillight (brown), ground (white). The red and blue wire can be used for brake control or auxiliary. Use on a small motorcycle trailer, snowmobile trailer or utility trailer. Can also be used as custom wiring on trailers with 3 light/wire systems. See "Tow Vehicle Taillight Wiring" below.
6way_rectangle_1.jpg 6 way tow vehicle side.
6way_rectangle_2.jpg 6 way trailer side.
6 Way Systems, Round Plug

Round 1 1/4" diameter metal connector allows 1 or 2 additional wiring and lighting functions such as back up lights, auxiliary 12v power or electric brakes. Note: The black (sometimes red) 12v and blue electric brakes wire may need to be reversed to suit the trailer. Check with a test light or VOM. Uses: horse trailer, travel trailers, landscaping trailer, car trailer, etc.


6way_vehicle.jpg 6 way tow vehicle side.
6way_trailer.jpg 6 way trailer side.
7 Way Systems

Round 2" diameter connector allows additional pin for auxiliary 12 volt power or backup lights. Uses: heavy duty landscaping trailer, car trailer, boat trailers, horse trailer, travel trailer, construction trailer, etc. Check with a test light or VOM.


7way_vehicle.jpg 7 way RV flat blade tow vehicle side.
7way_trailer.jpg 7 way RV flat blade trailer side.

Jan 01, 2011 | 2001 Pontiac Montana

1 Answer

95 ford f250 trailer wiring trouble what does each wire work and what color


The basic 4-flat trailer wiring colors are as follows.
Yellow-Left turn/Stop, Green- Right turn/Stop, Brown-Running Lights and White-Ground
7-way trailer wiring colors are as follows.
Yellow-Left turn/Stop, Green- Right turn/Stop, Brown-Running Lights, White-Ground, Red or Black-auxiliary power, Blue-Trailer Brakes and Purple-Reverse lights

Jan 15, 2010 | 1995 Ford F250

1 Answer

How do auto reverse brakes on a trailer work?


Forward Braking
The actuating force for the wheel brake is generated during braking of the towing vehicle, as the trailer tends to overrun and
pushes the drawtube in. This force is transmitted to the expander devices in the wheel brakes via the overrun lever, brake rod,
compensator and brake cables.
As a result, the brake shoes are pressed against the brake drum. The resulting friction from contact of brake linings and drum
produces the required braking.
On releasing the brake on the towing vehicle, the drawtube returns to its original position and the brake shoes are released from
the drums by means of the tension springs.
Auto-Reverse
During reversing the drawtube is pushed in and the brake shoes press against the drum (as in forward braking).
When the trailer wheels are in reverse, the reverse rotation, combined with the friction generated from drum and lining contact,
causes the sliding shoe to slide on its carrier towards the adjuster.
This displaces the sliding shoe radially inwards away from the drum. The drawtube may then travel fully to its end stop without
applying further force to the brake shoes and the trailer can be reversed without any difficulties.
Changing direction from reverse to forward travel results in the drawtube being pulled out, allowing the sliding shoes to be
returned to the forward braking position by means of the tension springs.
From this guide which contains more information also.

Oct 30, 2009 | 1997 Land Rover Defender 90

2 Answers

2003 ford ranger 7 pin wiring for a trailer all I need is what the colors on the wiring are blue/yellow/green/black/brown/white


White is ground, black is power to trailer battery trickle charge, blue is brakes, green is tail/running lights, red is left turn signal and left brake light, brown is right turn signal and right brake light, yellow is aux power/back up lights. This is the general color coding, there are exceptions, white, black, and blue are pretty much always as listed above, sometimes the others vary. If you find you are having trouble, post any further questions here, I'll be glad to help out. Curt

Apr 24, 2009 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...