Question about Cars & Trucks

Open Question

Berchet climbing frame screws - Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 93 nissan quest 3.0. I need to know where to locate all grounds on vehicle. . Please help..


If you climb underneath you will find a large cable that runs from the engine compartment to the frame. It is mounted differently on every vehicle.

Sep 01, 2014 | Cars & Trucks

1 Answer

Can u open renault megane car boot manually


Pull forward rear seats climb in boot with small screw driver and torch. On the lock will see a white slide push screw driver in and slide right boot should unlock

Jun 30, 2014 | Renault 181 Cars & Trucks

1 Answer

My 1998 1.8 jerks when climbing hills, suddenly had high rerves... So I had it checked and the mechanic said the problem was with the curburator, so i changed it.. now the car is iddling funny, its not...


You have a Fuel Problem, Sounds like either he screwed up on the Rebuild, it needs to be adjusted or there is a a chance there is an Electrical Issue that has not been identified...

Apr 09, 2013 | 1998 Volkswagen Golf

1 Answer

How do you change the headlight


On a Newer Vehicle you'll replace the Headlight Bulb
Open the engine compartment hood.

Locate the back of the headlight to determine the lamp and bulb type.
Decide which bulb you need to replace.
Purchase the correct bulb for your headlamp.
Behind the headlight the lamp the socket is removable.
Remove Socket then replace lamp (bulb).
Carefully re-install the socket


On Older vehicles:


Remove the screws that connect the headlamp frame to the
bracket holding the headlamp. Make certain you turn only
the screws that hold the lamp frame, not the adjusting screws.
Disconnect the electrical connector in the back of the lamp
by pulling the socket away from the headlamp with your hand.
Remove the headlight from the bracelet area and discard it.
Replace with the new headlight, making sure that it is positioned
right side up.
Plug the wire socket into the new headlight, which holding the
headlight securely.
Replace the headlight into the frame.
Place the frame onto the headlight bracket.
Reattach the screws to hold the frame and bracket in place.
Do not adjust the setting screws for the direction the headlight
shines.


At night partk in front of a wall and shine your lights on the wall
so see if the headlight shifted during installation.

Jul 14, 2012 | Cars & Trucks

1 Answer

Where is fuel filter 98 yukon


Climb under the Yukon with the drain pan, box wrench set and new fuel filter. Follow the fuel lines away from the gas tank until you locate the fuel filter, along the frame rail about halfway to the engine. good-day!

Sep 02, 2011 | GMC Yukon Cars & Trucks

1 Answer

I bought a 1997 chevrolet malibu from someone and they replaced the rack & pinion and they didn't tighten the bolts properly so the k frame broke and i need to weld the frame back so i don't...


You are in for a challenge. Most junk yards don't keep cars or parts that old. I suggest you spot just about any 1997 Chevy, Olds, or Pontiac Sedan, plus or minus two years, buy the owner a Coke, while you climb underneath, and have a look and take a picture or two.

Aug 28, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

How to replace oil pan gasket


1994-96 VEHICLES
( see Figures 6 and 7 / click image for zoom )


zjlimited_1359.jpg

Fig. 6: Oil pan mounting bolt locations-1996 3.1L engine shown

zjlimited_1360.jpg

Fig. 7: Oil pan sealant application points-1996 3.1L engine shown

  1. Disconnect the negative battery cable.
It may be necessary to remove the hood, with the help of an assistant, for access.
  1. Remove the engine mount strut and A/C compressor (if equipped) and the engine mount strut bracket assemblies.
  2. Remove the electric cooling fan assemblies. -28467 and J 26462, or equivalent.
  3. Raise and safely support the vehicle. Drain the engine oil.
  4. Remove the front exhaust manifold pipe.
  5. Remove the intermediate shaft bolt/screw.
  6. Remove the oil level sensor.
  7. Remove the engine splash shield.
  8. Suitable support the drivetrain and front suspension with jack stands.
  9. Remove the transaxle mount side frame retaining nuts from the drivetrain and suspension frame assembly.
  10. Remove the engine mount side frame nuts from the drivetrain and suspension frame assembly.
  11. Unfasten the rear drivetrain and front suspension frame bolts/screws.
  12. If equipped, remove the lower drivetrain and front suspension frame bolts/screws.
  13. Remove the engine mount assembly.
  14. Remove the flywheel inspection cover.
  15. Remove the starter.
  16. Disconnect the transaxle mount assembly from the oil pan.
  17. Unfasten the side bolts and screws and the retaining bolts and screws, then remove the oil pan. Remove and discard the oil pan gasket.
To install:
  1. Clean the gasket mating surfaces.
  2. Apply a small amount of sealer on either side of the rear main bearing cap, where the seal surface on the cap meets the cylinder block. Install a new gasket on the oil pan.
  3. Position the oil pan and secure with the retaining bolts and screws. Tighten the retaining bolts and screws to 18 ft. lbs. (25 Nm) and the side bolts/screws using tool J 39505 or equivalent.
  4. Fasten the transaxle mount assembly to the oil pan.
  5. Install the starter motor.
  6. Install the flywheel inspection cover.
  7. Install the engine mount assembly.
  8. Carefully raise the drivetrain and front suspension assembly. Install the rear drivetrain and front suspension frame bolts/screws.
  9. Fasten the engine mount frame side nuts to the drivetrain and front suspension frame assembly. Install the transaxle mount frame side nuts to the drivetrain and suspension frame assembly.
  10. Remove the jackstands from the drivetrain and front suspension frame assembly.
  11. Install the engine splash shield and the oil level sensor.
  12. Install the intermediate steering shaft bolt/screw. Connect the front exhaust manifold pipe.
  13. Carefully lower the vehicle.
  14. Remove the engine support tools.
  15. Install the electric cooling fan assemblies.
  16. Install the engine mount strut and A/C compressor, bracket and the engine mount strut bracket.
  17. If removed, install the hood assembly.
  18. Fill the crankcase to the correct level. Connect the negative battery cable. Run the engine to normal operating temperature and check for leaks.
Hope this helps (remember to rate this answer).

Jun 04, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

How do i adjust my 1997 ford Thunderbird headlights (vertical and horizontal)


There are screws (long screws) that move the light frame (and the light) up,down, left, and right on the outside of the frame of the headlights. It is a phillips head screw and flat on the end of the screw.

Sep 11, 2010 | Ford Thunderbird Cars & Trucks

1 Answer

Removing door panel from a 1997 GMC Suburban


Door panel is attached to door frame on the sides and bottom perimeter with push-in fasteners. There are screws that attach the arm rest/door pull to the frame , and also the panel trim around the door open/close handle.

Locate and remove all screws.

The perimeter of the panel is popped away from the door frame by inserting a flat blade screw driver between the panel and the frame.
There is a trim tool for this that works better than a screw driver. Pretty inexpensive from an auto parts store. Once the sides and bottom are free, the panel is lifted up to disengage it from the top portion of the frame where the panel is attached to the inside of the window trim.

Be careful not to pull or yank the panel too far out because of the wires that are attached to the inside of the panel.

Those plastic fasteners are replaceable, should any break when they are popped out (again, auto parts store carries these).
Hope this helps...

Jun 22, 2009 | 1986 GMC Suburban

1 Answer

How do I change a front headlight.


Bad news. Gotta remove the bumper. Does not make logical sense but the geniuses in detroit/tokyo/hamburg seem to have their heads up their tailpipe.
Its a pain in the a$$ if you are looking for an easy fix. Otherwise take it to dealer and pay $150 per light and another $300 for labor. If you are mech gifted, (1) remove grill, (2) remove radiator top 'retainer' (looks like top of radiotr), (3) remove tublular 'braces' holding bumper onto frame in grill area, (4) climb under car and remove press in "rivets" holding bottom of bumper onto bottom of frame. Not sure what to do next.....

Dec 27, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...