Question about Nissan Cars & Trucks

1 Answer

Headlights hood up to positive side of battery

Why would the headlights in a 97 nissan be hooked up to positive side of battery

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 16,221 Answers

Are you sure? What wire is it? Was there any fog lights installed? Does the headlight switch work right?

Posted on Apr 30, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I find headlight relay switch on a 85 Nissan extended cab p/u


Pretty sure there is no relay for the headlights. There are two 10 amp fuses in the fuse block, one for each side headlight. The power to the fuses is directly off the black fusible link (in your fuse link box, under hood, by the battery). Then the fused wires go into the headlight switch, and with switch on, out to the head lamps.

First check if the fuses have power to them. Hot at all times, so key can be off. If they have power, fuse link is good, so possibly a bad headlight switch or dimmer switch if no headlights..

Oct 03, 2015 | Nissan Cars & Trucks

3 Answers

Car starts off jumper cables


First-- the negative cable from the charging vehicle ,
does NOT go to your battery,it goes to the engine block

Only the positive cable goes to the vehicle being jumped

You will have a large 100 amp fuse or fusible link, that may look like a fuse or a hidden buss bar

You will need a wiring diagram to find a test point or place to open
things up
You may have fried several feature, once you get it to start & is drivable

Mar 15, 2014 | Nissan Pathfinder Cars & Trucks

1 Answer

Nissan quest dead battery - keys locked in van - get hood open


you need too get some sort of hook on the end of a handle, something smaller but still strong enough to pull against with out bending or breaking. then standing at the front of the van using a flashlight look through the grill until you find the hood latch, then locate the black cable running into the side of the latch hook on to it and pull as hard as you can while simultaneously bouncing pressure on the font center area of the hood with your other hand until you hear/feel the hood latch release or "pop"!

Nov 10, 2013 | 2006 Nissan Quest

1 Answer

97 NISSAN PICK UP NO POWER TO THE IGNITION


Ignition switch may be broken like mine was. Had same symptoms as you.

Feb 01, 2013 | 1997 Nissan Pickup

1 Answer

Can you help me change my headlight assembley? i have a 97 200sx SE


1.) Pop the hood to your Nissan. The headlight assemblies are only accessible from the engine compartment.

2.) Clear the area behind the bulb you are replacing. If you are replacing the passenger side bulb, you will need to remove the radiator overflow bottle. The bottle will unhook from its connective tube by pulling it toward the front of the car and up from the ground. If you are replacing the driver's side bulb, you may need to remove the battery. You will do this by unscrewing the positive (red) and negative (black) terminals that connect the battery to the engine, and then lifting the battery straight out of its housing.
3.) Remove the electrical connection on the back of each headlight assembly. This will be a bundle of wires with a wide plug sticking into the back of the assembly.
4.) Unlatch the plastic clip holding the headlight assembly case in place.
5.) Pry the small metal clip holding the bulb using your fingers or a screwdriver. Be careful not to bend, break or damage the clip or the bulb.
6.) Insert the replacement bulb into the headlight socket and reattach the metal clip that holds the bulb in place.
7.) Relatch the plastic clip holding the headlight assembly case in place.
8.) Reconnect the electrical connection to the back of the headlight assembly.
9.) Replace the radiator overflow bottle or the battery, depending on which bulb you replaced.

Mar 02, 2011 | 1997 Nissan 200SX

1 Answer

Need to remove and repair headlight motor on a 1988 corvette


REMOVAL & INSTALLATION 1984–88 Vehicles
  1. Open the hood, then turn the headlights on.
  2. Detach the headlight motor wire on the outer side of the headlight.
  3. Turn the headlights off (the disconnected light should stay open).
  4. Unfasten the 4 screws at the bezel. There are 2 at the front and 2 at the sides. Fig. 1: With the hood in the raised position, unfasten the Torx® screws from the outer side of the headlight bezel/trim piece 91036p23.jpg
    Fig. 2: You must then remove the screws from the inner side of the bezel/trim piece 91036p24.jpg

  5. Remove the bezel. Fig. 3: Remove the first of the top bezel/retaining ring screws . . . 91036p25.jpg
    Fig. 4: . . . then remove the remaining Torx® screw 91036p26.jpg
    Fig. 5: Lift the bezel/trim piece away from the headlight assembly 91036p27.jpg

  6. Remove the retaining spring by carefully using a hooked end tool, such as a cotter pin removal tool to move it to the side.
  7. Remove the headlight from the aiming pins by rotating the headlight toward the center of the car.
  8. Unfasten the 4 retaining ring screws, then remove the ring. Fig. 6: With the hood closed, you can see the 4 headlight retaining ring screws (1) and 2 aiming screws (2) 91036p28.jpg
    Fig. 7: Remove ONLY the 4 retaining ring screws, do NOT touch the aiming screws 91036p29.jpg

  9. Remove the headlight pump from the mounting bracket, unplugging the socket as you pull it away. Fig. 8: Remove the headlight away from the mounting bracket, unplugging the socket as you pull it away 91036p30.jpg
    To install:
  10. Install the headlight bulb, making sure it is plugged in properly.
  11. Position the retaining ring and secure with the 4 screws.
  12. Position the headlight into the aiming pins. Move the retaining spring back into place.
  13. Install the bezel and secure with the retainers.
  14. Turn the headlights on, then connect the headlight motor wire.
  15. Turn the headlights off. Both should lower.
  16. Close the hood. Check the aim of the headlights, and adjust if necessary.
1989–96 Vehicles
  1. Open the hood.
  2. Open the headlight door halfway. This can be done either by turning the headlight switch on, then back to the parking lamp on position, or by the manual headlamp control knob (which is located on the inboard side of the headlight door). NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
  3. Remove the screws from the front of the headlight bezel. NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
  4. Remove the Phillips head screws from each side of the headlight bezel.
  5. Remove the bezel by pulling it straight out from the engine side of the hood. Fig. 9: View of the headlight bezel mounting 91036g28.gif

  6. Unfasten the screws from the headlight retaining ring.
  7. Remove the headlamp from the assembly, unplugging the electrical connector as you are pulling it away. Fig. 10: Exploded view of the headlight assembly 91036g29.gif
    Fig. 11: Location of the headlight mounting and aiming screws 91036g30.gif
    To install:
  8. Attach the headlight electrical connector.
  9. Position the retaining ring and install the screws securing the ring to the headlight.
  10. Position the bezel in place on the headlight assembly.
  11. Install the screws on each side of the bezel and tighten to 51 inch lbs. (5.8 Nm).
  12. Install the screws on the front of the bezel and tighten to 17 inch lbs. (1.9 Nm).
  13. Cycle the headlamps, then close the hood. Check the headlight aim, and adjust if necessary.
prev.gif next.gif

Jul 07, 2010 | 1988 Chevrolet Corvette

2 Answers

Need to know where the crank shaft position sensor is on a 97 nissan pickup


1997 Nissan/Datsun Truck Pickup 2WD 2.4L SFI 4cyl The Crankshaft Position Sensor is located: Under hood, driver side, upper engine area, mounted in rear driver side of engine block.

Hope this help.

May 11, 2010 | 1997 Nissan Pickup

1 Answer

Where is the fuse box location for the 1995 nissan pathfinder. and wich one is the headlight fuse.


there are two fuse boxes on this vehicle on lower left side of dash panel, the other is on the right fender right behind the battery. I beleive the headlight fuses are in the one under the hood.Inside the cover should tell you which one is which.

Dec 06, 2009 | 1995 Nissan Pathfinder

2 Answers

Headlight out 97 Nissan Sentra


should just be the bulb. Open you hood and look on the back of the head light. should be wires going into the housing. Grab the fitting the wires are going through and turn, then pull out the bulb

Jan 01, 2009 | 1997 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...