Question about 2006 Jeep Commander

Open Question

My left turn signal wont stop blinking in my 2006 jeep commander.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75817 Answers

SOURCE: Turn signals not working on 2001 Jeep Grand Cherokee

replace the turns signals flasher unit.

Posted on Mar 02, 2009

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

  • 645 Answers

SOURCE: ac/heater fan switch problem on a 2006 jeep commander

next to the fan motor there should be a connector that has three or four wires that attached to the blower resistor. it should have two screws holding it to heater case, just pull it out and replace.

Posted on Feb 13, 2010

Testimonial: "This info was very helpful but need a little more info of where the fan motor is located. I will post another question to find that info."

Gozer
  • 435 Answers

SOURCE: install a altenator for a 2006 jeep commander

I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

Posted on May 21, 2010

  • 1 Answer

SOURCE: 2008 Jeep Patriot Fuse Replacement

but how do I get the light casing removed so I can replace it?

Posted on Jun 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal stays on a2006 jeep commander


Your turn signals are controlled by a electronic control module .The integrated power module . The switch is off an the turn lamp stays on ? No Low Beam Head Lamp Chrysler Pacifica Check out this guy's video , I know it's no same vehicle as yours ,but it's a Chrysler an jeep is the same manufacture. Chrysler Pacifica TIPM Electrical Problems .

Nov 30, 2015 | 2006 Jeep Commander

2 Answers

I just bought a new turn signal switch for my 2007 jeep grand cherokee how come my turn signals wont respond


2007? WK, (i own a 2010 with all docs)
same car.
REDUX
it dont work at all like a 1993, back in the day of running power through switches to run things.,
or with banks of relays, to fail.
every year,less relays like we did long ago in industry, (pure electronics)
i deleted all my fsm quotes.
it's to wordy.. (but accurate to a fault)
it's now networked + brains (puters),

the network map is below.
if you look at said map, the CAN-BUS network.

is a 2 wire, network for all communications
saving a ton of wire. (times all WK made world wide)
What happens is , you turn the switch
and it has this binary/resistance mux logic in the switch that goes to the SCM brain.

the SCM knows what you did, and converts your actions into a data stream, "a command".
to the can-bus.
it arrives, (if lucky)
to the FCM and the cluster brain CCN. (IP)

the cluster sees that and flashes the click sonic device, and flashes the blinker icon, lamps.
If you can't heare that ,this means the command was never arrived.at CCN.
the FCM hears this command and it in turn drives
the blinker bulbs on the 4 external lamps.

does hazards work, that be first fact to know..
and that FCM fuses, must not be bad.

we scan it next. to see if there are errors
on the can-bus.
or FCM sees garbled data
or CCN errors.
or more.... lots more,
or FCM not responding,

the FCM is over $800 so doing the diagnosis correctly can save a lot of cash.
guessing here can exceed $2000.

here are the can-buss signals, (using my scope)
wanna Gue$$ or Test.?c7b24520-c34f-45b7-b61c-d7988e7e8c8b.jpg

Jul 03, 2014 | 2007 Jeep Grand Cherokee Overland

1 Answer

Turn signal and Hazzards issue


Turn signal flasher. Replace with a heavy duty one.

Mar 20, 2014 | 2001 Jeep Cherokee

1 Answer

2007 jeep grand cherokee. why does my left turn signal stays on when im driving?


2011 HYJACKED.
WOW
Q1,only on cluster or there and both left corners of car
key to solving this ,knowing just that.
Q2,car drive perfectly and with headlamps on OK?
no charge/bat warning lamps in cluster, etc.?

can be ...ONLY 1 THING, OR 2?
this car, does not work like you think its no 93
this car (i own one)
has digital comes now
and a network
and now a virtual blinker (called just software now)
just like cruise control, software only.

so when you move the lever, it closes a digital switch.
fixing thing works best first knowing now it works.'
unless rich and shot gun swaps are you style.
this jeeps, the blinker switch wire goes
steering controls SCM ,there.chapter 19
649ohms is the code for left (cav2 >cav3)
then SCM send data on to the network "Can-buss" complex.
if switch fails, then it cant cancel
ca1>2.>3, all there go open status, infinity
the SCM see that state and transmits the command, blinks off,.
the code is "neutral"

the cluster sees this command and killls left blink
why would left kill fail and not right, Impossible.same code.

then same command goes to front MIP box. to FCM
front control module. if it cant here the netural command it hangs.
the actual module name is"front controL"
so if you have no scan tool you are sunk.
scan it and there will be errors. I bet.

what can you do besides scan it
sure fuses, and rest battery.
pull battery neg lug,but may kiLLL radio (lost pass word)
i say fCM scrambled.
or scm same.
one of the other. if the cluster fails , scm
if cluster works (stops blinking then FCM failure




see WK books even free !
here
http://jeepdied.com/books.html

Dec 08, 2011 | Jeep Grand Cherokee Cars & Trucks

2 Answers

2008 Jeep Patriot Fuse Replacement


If it is just the left side the bulb is probably blown. fuses will take out both sides

Jun 14, 2010 | 2008 Jeep Liberty

1 Answer

Jeep Liberty Left Rear Turn Signal Not Working


sounds like the bulb you have is the wrong resistance the new noen bulbs will do this

Nov 16, 2008 | 2004 Jeep Wrangler

Not finding what you are looking for?
2006 Jeep Commander Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...