Question about 2007 Hyundai Veracruz Limited

Open Question

Air blend door actuator

No heat on passenger side

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: Where is the air mix actuator located for passenger side

If youve changed stereos or done anything under the dash the connection could have come undone or it may have a vacuum assist and the small hose came off either way it should be close to the floor under the dash in the center if it is a vacuum the small hose will connect to a piece that is silver round and cone shaped

Posted on Jan 07, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

2010 sebring heat on drivers side cold air on passenger side?


blend door actuator not working

1 - Blend door actuator 2 - Mode door actuator 3 - HVAC wiring harness


26340343-zk4yuwqxbgfnkewmrnymectq-4-0.gif

26340343-zk4yuwqxbgfnkewmrnymectq-4-1.jpg

Nov 04, 2016 | Cars & Trucks

1 Answer

Where is drivers, mode door and blend door actuators located


Blend air door actuator (temp)on left side of heater box near the gas pedal below it may be the mode door & passenger side has a temp door actuator for that side.

Nov 21, 2015 | 2000 Dodge Caravan

1 Answer

08 dodge nitro blows hot air on passenger side but cold air out the drivers side!! Any answers




NOTE: LHD model shown. RHD model similar. All vehicles are equipped with a common heater, ventilation and air conditioning (HVAC) housing assembly (1). The heating-A/C system combines A/C, heating, and ventilating capabilities in a single HVAC housing mounted within the passenger compartment behind the instrument panel. The HVAC housing assembly includes:
  1. Mode-air doors (2)
  2. A/C evaporator (3)
  3. Recirculation door actuator (4)
  4. Air inlet housing (5)
  5. Recirculation-air door (6)
  6. Blower motor (7)
  7. Blower motor resistor (8)
  8. Heater core (9)
  9. Air distribution housing (10)
  10. Blend-air door (11)
  11. Blend door actuator (12
  12. Floor distribution ducts (13)
  13. Mode door actuator (14)

Jan 28, 2015 | 2008 Dodge Nitro

2 Answers

Heat comes thru driver's side vents, but blows cold air thru passenger side vents


You likely have a faulty blend door. It could be electrically, mechanically related, or even a broken door. It may be the blend door motor, or possibly the temp sensor.

Dec 30, 2012 | 2010 Ford Flex

3 Answers

Driver side blowing hot air passenger side blowing cold air


I'm having the same problem except on mine it's the driver's side that's blowing cold. Do you have the pictures in a finer resolution? I can't make them out and when I zoom, they are too grainy. Does the replacement require removing the dashboard? What's the general cost of the acuators? Are they readily available at like NAPA or other parts stores?

Nov 26, 2011 | 2006 Kia Amanti

2 Answers

AC blows hot air on the driver side and cold air on the passenger side


You may have a bad temperature door actuator motor on the drivers side. The actuator is what moves the temperature blend door and when it fails it usually moves the door all the way to the "hot" position. Sometimes if you shut the vehicle off for a bit then restart it the system will work fine for a while then the actuator will again swing the door all the way open or shut. I've replaced several of these actuators [both drivers side and passenger side] for similar problems.

Jul 08, 2010 | 2005 Chevrolet Silverado

4 Answers

The heater in my 2003 Dodge Ram 4x4 will not heat up or gets only luke warm & only on the passenger side....any suggestions?


Cold on drivers side and heat on passengers side, actuators working properly and blend doors are moving. Heatertreater is for piece of plastic on actuator motor. I moved blend door by hand after disconnecting actuator and works fine, both sides freezing when moved in opposite direction.

Dec 04, 2009 | 2004 Dodge Ram 1500

2 Answers

200 Jeep Laredo..Air is cold and fan is blowing,


there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.
7d2da02.gif
  1. Disconnect and isolate the negative battery cable.
  2. Remove the glove box from the instrument panel.
  3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
  4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
  5. Remove the blend door actuator from the vehicle
to instal
  1. Position the blend door actuator into the vehicle.
  2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
  3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
  4. Connect the HVAC wire harness connector to the blend door actuator.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable.

Sep 09, 2009 | 1998 Cadillac Seville

2 Answers

Heat flowing on passenger side only


your actuatior foe the drivers blend door is stuck. try unhooking battery for a few minutes have both on heat and hook back up and start up. the actuators will run thru a learn mode and sometimes this will free up.if not you will need an actuator

Dec 09, 2008 | 2005 Chevrolet Silverado

Not finding what you are looking for?
2007 Hyundai Veracruz Limited Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...