Question about 1997 Isuzu Rodeo

1 Answer

Bleeding clutch just installed a new trany and clutch. clutch petal falls all the way to the floor and will not rise back up by itseslf. Tried bleeding it and petal remains the same.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 21,873 Answers

Are you sure the clutch disc and fork are connected to the slave cylinder ?

Posted on Apr 29, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New clutch installed. No pedal, stays on floor unless I bring it back up with my hand. No resistance.


`Did it bleed, did fluid come out in a steady stream? Isn't there a spring to bring the pedal off the floor?
Check the linkage of the pedal to rod to the clutch master cylinder, make sure that is all together. Any chance the master has an internal leak and won't build hydraulic pressure down at the slave? If you get it bled, then watch the slave operation while someone works the clutch pedal. The piston on the slave should extend and push the clutch fork enough to disengage the clutch.

Jul 19, 2015 | Nissan Cars & Trucks

1 Answer

Hydraulic clutch slave cylinder


this symptom would typically be solved with a new cluth slave cylinder. Check to make sure the fluid is full in the master cylinder reservoir. If the fluid is empty then there is either a leak, or the clutch is has worn. filling the reservoir and bleeding the system may get you back on the road.

Apr 30, 2013 | Isuzu Pickup Cars & Trucks

1 Answer

What does it mean when the clutch petal goes all the way to the floor in my 2003 suzuki aerio


Your clutch fluid reservoir may need brake fluid-yes, it uses brake fluid as a hydraulic fluid. Check reservoir on the firewall. It will sit beside the brake master cylinder. The reservoir sits atop the clutch master cylinder.
If it was dry, the clutch may need bleeding down at the slave cylinder on the transmission housing-where the clutch fork sticks out of the transaxle.. Open the bleed valve on the slave cylinder, and have someone slowly press clutch down. Keep bleeding until a steady stream of fluid comes out when clutch is pressed. Then close bleed valve, check clutch operation-pedal should have some pressure on it now.

Dec 10, 2012 | Cars & Trucks

2 Answers

I have a 2000 Isuzu Rodeo in which the clutch pedal went to the floor & stayed there. Upon inspection, the clutch master cylinder was empty on fluid. I filled the reservoir & bleed the clutch...


It sounds as if you have 2 problems here.

The fact that the clutch pedal went to the floor and stayed there suggest a fault in the master cylinder. It may be that you need to overhaul the master cylinder.

Overhaul kits are available at less cost than a clutch master cylinder:
0results for isuzu rodeo clutch master cylinder overhaul kit

The grinding noise ... A grinding noise would be caused by either the gear not engaging properly because of the defective clutch.

Or, if it is more of a squealing noise - that may be the clutch release bearing at fault.

Are you absolutely sure that your entire clutch unit - pressure plate, driven plate and release bearing aren't worn?
116results for isuzu rodeo clutch

Mar 14, 2017 | 2000 Isuzu Rodeo

1 Answer

1993 chevy silverado 4x4 4.3 4sp. clutch issue


somthing is leaaking down then from what your desribing. probably the slave is it leaking fluid into the bellhousing?? these do trap air badly too because the bleeder is on the rear of the slave and it runs down hill with the drive train. jack the rear of truck as high as possible to get the air to rise to bleeder and bleed again

Aug 26, 2009 | 1995 Chevrolet Silverado 2500

2 Answers

Clutch has no pressure, but no leaks.


That would be a pressure plate problem.

Jun 08, 2009 | 1989 Ford Probe

1 Answer

2003 town and country brake problem


Did your mechanic use a DRB III or equivalent scanner before performing the bleeding procedure after installing the master cylinder? This is a requirement by the manufacturer (Chrysler) when bleeding the brake system.

Jan 16, 2009 | 2003 Chrysler Town & Country

1 Answer

New Mastercylinder/brakes still lose pressure


ITS THE MASTER CYLINDER AGAIN.More than likely they are using a re manufactured master cylinders. Get a new one from MOPAR-(CHRYSLER) that will take care of your problem. Trust me I have had the same problem with a similar vehicle in the past in my shop. Good Luck, thank for using FIX YA

Jan 16, 2009 | 2003 Chrysler Town & Country

1 Answer

Clutch problem


Hi,
Check any flexible hoses used for condition, check clutch reservoir that it still contains fluid.

If it does, ask an assistant to press the clutch down fully - while you watch the liquid level. It should fall, then rise again when off the pedal. If it just stays put, you need new seals on the master cylinder.

If all the fluid is gone, but no obvious leaks, remove the slave cylinder, and replace the seals in that or replace with new unit.

it is possible that you just have a slight leak in the slave cylnder, allowing the fluid level to fall enough to allow air in the system giving the fault. Again, replace seals in slave cylinder, and refill with clean brake/clutch fluid, and bleed out the air using the bleed nipple on the slave cylinder.

Any reasonable garage will do this for you if access is difficult.

Thank you for using Fixya!

Jul 05, 2008 | 2002 Jaguar X-Type

Not finding what you are looking for?
1997 Isuzu Rodeo Logo

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...