Question about Cars & Trucks

1 Answer

Remove door panel 08 sienna

Hang tag slid down between driver door console and door panel. How much do I need to remove, and how?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

If it slid in it should slide out!! OPEN console door....

Posted on Apr 29, 2013

  • joel achtenberg Apr 29, 2013

    I may not have been clear. It slid BETWEEN the storage compartment and the door panel. As illustrated (by an envelope) in the photo.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
countrysi248
  • 443 Answers

SOURCE: I need to remove the door panel on my 2004 Avalanche

There are plastic clips that hold the door panel inplace .. First look for any hidden screws near the door handle . there might be a little plastic cover that you need to remove with a small screw driver to find the screws.. look under the handle also to see if there are any hidden screws . next take a flat blade screw driver and start at the bottom corner and try gently prying the door panel off . try to stay close to the plastic clips not to damage them by prying real hard .. once you have snapped them loose all the way around .. lift up on the door panel to remove it from around the window lip and out it should come.. holler if you have any problems.. usually The mirrors on the chevys are up above the panel and there is a triangle plastic cover over it on the inside .. it will pry off also gently and there are 3 nuts there that need to be removed .. use caution these fall behind the door panel ... holler if you need more. Jerry

Posted on Apr 24, 2009

mechanicm639
  • 253 Answers

SOURCE: driver door panel removal and re-connect door pull

You most likley have a damaged inside door handle. To remove the door panel, you must first remove the handle bezel. The trim piece around the handle. It is held in place by 4 retainer tabs, take a small flat screw driver, insert it between the bezel and handle. Gently pry away from the handle. If you look in the crack around the handle you will see the tabs. When you get that off, remove the switch assembly by prying up on it gently, unplug the wiring. There are 2 screws in the door panel where you pull the door shut, remove those also. Start at the bottom front of the door panel, pull outward firmly, but not violent. The retainers will come out, you will most likley break some, this is common. The inside handle is about $45 from your dealer. If it is the handle it is held in with 1 rivit, drill it out with a 3/16 drill. Replace the handle, reassemble. Good Luck.

Posted on May 05, 2009

  • 187 Answers

SOURCE: How do remove drivers side door panel

First you need to remove the door handle and window crank by pushing back the ring and releasing the handles. Also the arm rest will have screws into the steel door frame that must be removed. The panel itself has plastic snaps that are pushed into holes in the doors steel frame. The trick is to slide a pry bar or even two is better, one on ether side of the clip and force the pin out. You need to be patent and do one at a time. The door panels are made of a less than hard strong material and will brake apart easily especially if they are older. The clips go all the way around the lower three sides and the top will lift off the sill.

Posted on May 07, 2009

  • 1986 Answers

SOURCE: how to remove a 1999 civic se left door panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: I need to remove the door panel on my 2004 Avalanche

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them.

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sienna window won't come down all the way


Remove the inner door panel & find out why

Feb 08, 2013 | 2007 Toyota Sienna

1 Answer

NEED TO REMOVE DOOR PANEL ON A 2004 CHEVY AVEO


Click the link below:-----Door Panel Removal?

--------
How to remove the door panel to install a new window regulator?
http://howtobyme.blogspot.com/2011/08/how-to-remove-door-panel-to-install-new.html


---------
Hummer H2 Door Panel Removal? http://technoanswers.blogspot.in/2012/07/hummer-h2-door-panel-removal.html Hummer H2: How to remove Front Door panel? http://www.howtobyme.blogspot.com/2012/07/hummer-h2-how-to-remove-front-door.html 2009 Hummer H2 Door Panel Removal http://schematicsdiagram.blogspot.in/2012/07/2009-hummer-h2-door-panel-removal.html

-----------
how to remove window motor on driver side door panel?
http://technoanswers.blogspot.com/2011/08/how-to-remove-window-motor-on-driver.html


-----------
ford explorer window motor, regulator and door panel removal?
http://technoanswers.blogspot.com/2011/02/ford-explorer-window-motor-regulator.html


---------
Keep updated for more help.

Nov 19, 2012 | Cars & Trucks

1 Answer

2003 sienna tail light need replacing. How do I gain access to replace lightbulb. There is a nut on the hatch, do I reomove the nut and the light assembly come out? Help if you can, thanks,


If the 2003 is like my 2002 Sienna and you are trying to replace the light within the hatch, then you have to access this light assembly through the rear interior panel. You can not remove the lens or the light assembly from the exterior of the vehicle. This really did take about 10 minutes.
Step 1 - remove the 2 screws from the hatch back handle by flipping the covers down to access the screws. Insert a screw driver about 1/16 of an inch into the top of each end of the handle to flip the covers down. This will expose the screws.
Step 2 - Use a socket drive wrench to remove the 10 mm screw from each end of the handle.
Step 3 - Use a screw driver to slide the cover up and off of the retaining clip on the left (drivers) side of the rear panel and remove the 10 mm screw from the clip.
Step 4 - Now the only thing holding the back interior panel on is about nine plastic clips. Carefully pull the panel away from the door starting at the bottom where the handle was removed. Work your way across the bottom and up the left side popping each of the snaps loose. Move back to the right and in my case the panel fell off in my hands. I was able to remove and replace the light with ease at this point.

Apr 30, 2011 | 2003 Toyota Sienna

2 Answers

Rear passenger side window just fell down and won't go back up. is this possible?


Yes its possible, the roller has come out of the track You would have to remove the arm rest and panel screws off and remove the cover with the door open unsnap the clips on the door and let the door hang down use a flashlight to see the roller that's off track pick the glass up and slid into the glass guides and move the window up till you get the roller into the track, have the key on in case you need to raise the window up or down to get it to go into the track, if the roller is broke you can buy one at a junk yard, if the roller is ok then the stop pin may have fallen out and you will have to use a roll pin to keep the roller from coming out of the track. Hope this helps.

May 14, 2010 | 2004 Cadillac CTS

1 Answer

Could not open driver side manual sliding door in my 2003 Sienna


need to remove inner panel.. be careful not to break panel... ck latch seems broken.. o

Jul 22, 2009 | 2000 Toyota Sienna

1 Answer

Need instructions on how to remove center console to access electric window switch.


Here is what I could find, hope it helps.
Good luck.
Regards,


REMOVAL & INSTALLATION

See Figures 1 and 2
The following procedure is a general procedure for console removal. You may have to modify or skip certain steps depending upon your vehicle.
  1. Disconnect the negative battery cable.
  2. Remove the shift knob, floor compartment door and console trim plate.
  3. Remove the instrument panel accessory trim plate.
  4. Unfasten the retaining bolts, detach the connector, then remove the console door.



0900c152800900b7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the retainers, unplug the connector, then remove the console door
  1. Remove the seats, as outlined later in this section, in order to get to the lower rear screw(s) on the side trim panels.
  2. Remove the console side trim panels.
  3. If equipped, remove the switch pack housing with the switches.
  4. Remove the console compartment floor protector, bolt covers and bolts.
  5. Unfasten the screws mounting the console to the instrument panel and tunnel.
  6. Unclip the harness and accessory plug.
  7. Tag and detach all necessary electrical connectors.
  8. If necessary, remove any remaining retainers.
  9. Tilt the rear of the console up, then slide the front tab back out of the instrument panel and remove the console from the vehicle.



0900c152800900b8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Exploded view of a typical console mounting
To install:
  1. Position the console in the vehicle by placing the front tab of the console into the instrument panel slot, making sure to align the screw holes.
  2. Attach the electrical connectors as tagged during removal.
  3. The remaining of installation is the reverse of the removal procedure. Tighten the console retaining screws to 89 inch lbs. (10 Nm).

May 04, 2009 | 1986 Chevrolet Corvette

1 Answer

Power door is not delatching


there is a door lock actuator that has failed, it releases the latches so the door can open. you need to remove the door panel. unbolt the window and tape it as to hold the window up then remove the window regulator assembley then unbolt the lock actuator from the back side.

Apr 23, 2009 | 2004 Toyota Sienna

1 Answer

Remove door panel on drivers side 1998 sienna


there should be two screws holding it to the door panel could be concealed under a cover hope this helps regards Jim

Apr 06, 2009 | 1998 Toyota Sienna

3 Answers

The sliding door handles of my 1998 Toyota Sienna have both broken.


I replaced both of my sliding door handles this weekend. It was actually pretty easy. Cheapest I could find the handles was a little over $70 each. The interior panel is held on with one screw and 10 nylon clips. The one screw is in the cup holder. Put you hand in the cup holder and push out at the bottom. It pops right off exposing the one screw. I started on the clips from the top at a corner. Seemed to be the easiest place to slide a screw driver under. Once I got the screw driver in, I started working my fingers under the panel. The clips run mostly along the top and bottom about 6 inches from the edge. I made an effort to apply the force as close to the clips as I could to reduce flexing the panel. Once I got the first clip to pop out the other followed pretty easy and the panel lifted right off. Carefully peel back the plastic barrier. The exterior handle is held on with two 10mm bolts. Connecting the short cable was pretty obvious once you could see everything. Now I have to teach everyone to open the side doors very gently! Hope this helps.

Sep 21, 2008 | 1998 Toyota Sienna

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...