Question about Cars & Trucks

Open Question

My mobility scooter slips in forward gear and wont pull off

My freerider Westminster slips in forward gear and wont pull off, I can hear the motor turning and can feel it slipping, reverse works perfectly, any advice would be helpful as I cant afford to get it repaired by a professional,

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pittmanc
  • 194 Answers

SOURCE: Mercedes after shifting to reverse to drive the 1st gear slips

they didn't line the motor up properly now ur transmission is at to much of an angle and it is making it slip

Posted on Dec 05, 2008

Ad
  • 295 Answers

SOURCE: automatic trans slips 92 ford explorer

I would have the transmission check if you plan on keeping the car a long time. The lucas oil is an additive for the oil. The additive is making the fluid a little heavier and tricking the soleniods or clutch and bands with a different pressures.

This is a temporary fix. The transmission over time is going to start to slip more and more.

Posted on Mar 18, 2009

  • 8 Answers

SOURCE: please help

1. check fluid level... is it low?
2. is the fluid red just like it came out of the bottle or is it brownish, burnt and have solid particles clicking to the dipstick?
3. pull the pan off the transmission and check for clutch/band particles laying in the bottom of the pan (if there, the trans needs rebuilt or replaced with known good one)

Posted on Jul 24, 2009

Molson02536
  • 3854 Answers

SOURCE: I have a 1997 chevy 1500. The Trans (4l60e) is bad i think

Before guessing at transmission problems, check the fluid level (car warmed up, engine running in Park on level ground) and have the PCM scanned for trouble codes FIRST.
Secondly, put a line pressure gauge (or visit a local trans shop) on the pressure test port and go for a drive to verify proper line pressure. Base pressure at idle in P,N,OD should be around 70psi and around 140psi in R. Max line pressure should be at least 190psi at WOT in 1st or 2nd, 225psi is optimum. If base pressure is low, trans or pump is worn out. If max pressure is low, check EPC solenoid. If reverse is slow to engage, and line pressure does not come up to at least 130psi in reverse, replace the boost valve with a Transgo 0.500" boost valve (easy fix in pan).
Slow, slipping or no reverse: “lo-reverse” clutches are worn out, fluid leak in the reverse apply circuit, or broken sunshell. It is possible to remedy a fluid problem by removing the checkball from its cage in the case in the rear of the trans may help (must remove valvebody), or adding a high-viscosity additive such as Lucas Transmission additive or other seal restorer product. May also have worn boost valve (can replace in the pan).
Soft shifting, gradual performance degradation: Poor line pressure rise due to leaking boost valve, clogged EPC filter screen, failing EPC solenoid, or worst case: leaky seals throughout. Transgo HD2-C kit fixes first two without removing trans. Seal restorer may fix last problem, but probably R&R. Also try a transmission flush with BG brand products (Firestone stocks it).
No movement in any gear: pump failure, or total loss of fluid. R&R, or refill pan and find the leak. If out of fluid, avoid running the engine until the trans is refilled to avoid pump damage. To check for pump failure, check fluid level with the engine off, then start the engine and recheck fluid level. If level does not go down when engine is running, the pump is broken.
1-2 or 2-3 shift is slow/soft above part throttle: Trans is on its way out. R&R
Good luck and start with checking your transmission fluid level. Thank you for using Fixya

Posted on Mar 16, 2010

  • 90 Answers

SOURCE: my reverse gear wont work

try to change the oil and filter in the transmission, if you still have no reverse , replace the transmission

Posted on Dec 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

EZGO Electric. Motor runs but will not go in forward or reverse.


It sounds like you may have a sheared keyway or pin on the input shaft to the differential. It is highly unlikely that all of the teeth could be stripped from the pinion gear. If you pull the motor loose the problem should be very easy to find.

May 15, 2017 | Cars & Trucks

1 Answer

It sound if the clutch is slipping while driving in 5 gear but if the bakkie is standing still and you select 5 gear and leave the clutch the engine pull dead


If it were slipping in 5th, it would be slipping in all gears. If your hearing noise in 5th, possibly a shaft bearing

Oct 01, 2016 | Cars & Trucks

1 Answer

TAPPING NOISE, NOW IT WON'T GO INTO GEAR WITHOUT LOUD GRINDING NOISE AND ACTS LIKE TRANSMISSION WON'T ENGAGE TO DRIVE


If it is an automatic transmission, first check the fluid level. If it is low, fill it up and try it again. If the level is fine, then there is a bigger issue and you should seek a professional's help.

Jun 18, 2017 | 1996 Buick Century

1 Answer

2004 Linclon LS went to start it wont start makes a winding noise sounds likes its not catching


Sounds like the gear on the starter is not sliding forward on the shaft to engage the ring gear so what you are hearing is the starter motor spinning free. So absent any other clue I would suspect the starter needs to be replaced.

Nov 29, 2010 | 2004 Lincoln LS

1 Answer

G35 sedan driver seat wont go forward/back


Check for obstraction on rails(coins , lighter etc..) first.
If it has stripped gear, you would hear it.

May 26, 2010 | 2004 Infiniti G35 Sport Coupe

1 Answer

Truck wont shift out of first gear at the right rpm.Some times second gear is there others it is not. Same for third. trans dont slip when its in gear.


you'll want to check your detent cable at the throttle body, if the cable is tight then it's out of adjustment. you should have slack in it. Basically it's trying to stay in low gear because it thinks your at wide open throttle and needs to downshift. There's a clip that you have to pull out and the pull the cable forward and at the same time put the clip back, this will give you slack. You may have to adjust it a few times.

Dec 15, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

2003 Toyota Camry drivers side power seat stuck


This is not necessary...as many have stated...use a hammer with switch in reverse position. Hammer the seat back...it will catch...

Aug 25, 2009 | 1992 Toyota Camry V6

1 Answer

Rear window of 92 Ford Bronco wont go up or down (power windows)


You need to either replace the motor or get a rebuild kit for the head unit. You remove the motor and take out 2 bolts in the head, use a flat blade screwdriver and hammer the pinched areas to get access to the inside gear. its a nylon gear and has 3 nylon runners inside. yours will prob be in pieces that are mixed with thick grease. best to clean all that out. the rebuild kit is pretty cheap or you can just cut a bolt into 3 similar sizes and drop them in the slots. (just remember the slip action the nylon is a safety feature in case you get your head or arm caught in the window as it closes) the metal pieces make it stronger and more dangerous. Put the head back together, pinch the metal tabs, put it all back on. Same solution will work on the door windows as well.

Mar 29, 2009 | 1992 Ford Bronco

1 Answer

Transmission wont pull in reverse and takes a second to catch in drive overdrive and second gear


you need it rebuilt. lol the clutches are worn out in forward gears, producing the late engagement and slipping, and reverse is burnt out. The fluid probably isnt red anymore, check to find out, but it needs to be removed and serviced before the etire transmission gives out.

Jul 24, 2008 | Ford Bronco II Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...