Question about Toyota 4Runner

Open Question

Flywheel bolt torque 1fz fe - 4Runner Toyota Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 375 Answers

SOURCE: Flywheel bolts torque settings

Check with your local auto parts store. Or buy a repair manual

Posted on Jul 01, 2008

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

morse008
  • 1111 Answers

SOURCE: I need torque settings for 1600 beetle engine SP

wiki this

Posted on Aug 25, 2009

  • 5 Answers

SOURCE: Head bolt torque specs?

I really really really hope you turned the bolts an additional 90 degrees after torquing to 22 Ft-lbs. Otherwise, you may be taking that head off again.

Best of luck,

David

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

What is the torque setting for nissan navara v6 4lt2007 flywheel torque


there are 2 sets of torque specs for flywheel bolts as there are 2 different fly wheels in use with different bolts for each
go google and type in--torque specifications for nissan navara flywheel bolts and fins a site relevant to you application
it could be 61-69 ft/lbs a or 90 ft lbs depending on the flywheel and the vehicle 2wd or 4wd

Sep 30, 2015 | Nissan Cars & Trucks

1 Answer

Torque bolts for flywheel 2003 Hyundai Santa Fe


94 -101 ft/lbs- dip the bolts in clean engine oil or use never-seize on threads. use new bolts

Feb 06, 2015 | 2003 Hyundai Santa Fe

1 Answer

Toyota 80 series GLX auto landcruiser 1996 need head bolt torque a nd cam shaft torque settings


Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Nov 22, 2014 | 1996 Toyota Land Cruiser

2 Answers

How many ft/lbs of torque is recommended on the flywheel bolts when installing the flywheel on a 1996 GMC Sierra Z-71 4x4 5.7L engine?


GMC Sierra Bolt Torque Specifications. ... The torque converter bolts to the flywheel with 46 foot-lbs. of torque. ... 1996 GMC Sierra Horsepower Torque Specs.

May 02, 2014 | Cars & Trucks

1 Answer

1997 jeep wrangler 6 cylinder flywheel torque


It depends on what you are calling "flywheel". If it is a manual transmission, the vehicle is equiped with a true "flywheel", if it is equipped with an automatic transmission, it is equipped with a "flex plate" which a lot of people refer to as a flywheel.

With that said the torque specs are:
Flywheel-to-crankshaft bolts - 105 Ft. Lbs (142 N.m)
Flexplate-to-crankshaft bolts - 55 Ft. Lbs (75 N.m)

May 14, 2012 | Jeep Wrangler Cars & Trucks

1 Answer

Whats the head torque for 1FZ-FE.6 Cylinder


12 ft lbs / 16 nm
Please read full installation instruction (middle of the page) before install.
Link HERE

Jul 30, 2011 | 1994 Toyota Pickup

1 Answer

Where's the cranck sensor located?


Click the boxes with a red x in them to see diagram images. 5VZ-FE Engine
  1. Disconnect the crankshaft position sensor harness. Fig. 1: Exploded view of the crankshaft position sensor mounting 86824pa8.gif

  2. Remove the bolt retaining the sensor to the vehicle.
  3. To install, attach the sensor to the vehicle, tighten to 69 inch lbs. (8 Nm).
2VZ-FE and 3VZ-FE Engines
  1. Remove the engine under cover.
  2. Remove the alternator.
  3. Unbolt the alternator bracket.
  4. Disconnect the crankshaft position sensor harness.
  5. Remove the bolts securing the sensor and the sensor. Discard the O-ring.
  6. When installing, apply a light coat of engine oil on the O-ring, install on the sensor tighten the bolts to 74 inch lbs. (9 Nm).
1FZ-FE Engine
  1. Remove the engine under cover.
  2. Unbolt the sensor protector. Fig. 2: Exploded view of the 1FZ-FE crankshaft position sensor mounting 86824pb3.gif

  3. Disconnect the crankshaft position sensor bracket and harness.
  4. Remove the bolt, nuts and sensor.
  5. When installing, attach the sensor and tighten the bolt to 14 ft. lbs. (20 Nm) and the nuts to 78 inch lbs. (9 Nm).

Jan 28, 2011 | 1989 Toyota 4Runner

1 Answer

Timing belt diagram


complete procedures are posted at AutoZone.com: http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c152802619fd

Do you mean timing belt ot serpentine (accessory) belt?
Belt diagrams are below:


0900c15280261782.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Belt routings on the 1FZ-FE engine



0900c15280261783.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Belt routings on the 3RZ-FE engine



0900c15280261784.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Belt routings on the 5VZ-FE engine
2UZ-FE Engine
To remove the serpentine belt on the 2UZ-FE engine, position a suitable sized wrench or ratchet and socket over the belt tensioner bolt, rotate the tensioner counterclockwise to release the belt tension, then remove the belt. The pulley bolt for the tensioner has a left-hand thread.
When installing the belt, make sure it fits properly in the ribbed grooves and check to be sure the belt has NOT slipped out of the groove on the bottom of the pulley.



0900c15280261785.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. On the 2UZ-FE engine, rotate the belt tensioner counterclockwise to release the belt tension

Aug 25, 2010 | 2000 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...