Question about Cars & Trucks

Open Question

How to bleed brakes on a 2000 olds bravada. - Cars & Trucks

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 4340 Answers

SOURCE: bleeding brakes 2000 suburban wsith ab

Why were the brake lines replaced?

Sounds like the mastercylinder may have run dry. You have to bench bleed the master and then DO NOT allow fluid to run low, while bleeding brakes...

if master cylinder runs low on fluid and air gets in, almost impossible to bleed with out releasing the lines and bleed master it self.

Posted on Sep 20, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i bleed heater

1997 Oldsmobile Bravada heater core removal - YouTube

? 3:22

Oct 25, 2012 - Uploaded by Lloyd Ankney
1997 Oldsmobile Bravada heater core removal ... How can I replace a blend door actuator on a 99 Bravada? .... Heater core replacement 2000 S10 4.3L ( slideshow picture ) - Duration: 3:52. by Joe Lleras 169,585 views. 3:52.

Oldsmobile bleed air in heater core Cars & Trucks ... - Fixya > Forum > Tags > bleed air in heater core > Cars & Trucks
If your cooling system has any bleed screws incorporated, crack them once in a while as well. 2000 Oldsmobile Bravada heater blows cold air. Had a new heater .

Oct 25, 2015 | 2000 Oldsmobile Bravada

1 Answer

I have a 2000 oldsmobile bravada I changed the front brake line but now I have no brake fluid going to the back brakes. I have tried to bleed them but only a little fluid will come out. What's wrong?

Are you just opening the bleeder and letting it run out? If so have someone pump the brakes and hold the pedal while you open and close the bleeder don't let off the brake pedal until bleeder is closed . Repeat this process until only fluid comes out . You probably have to bleed both sides . Keep an eye on the fluid so the resivor doesn't run out then you'll have start all over.

Nov 09, 2014 | 2000 Oldsmobile Bravada

1 Answer

I replaced the brake pads on the rear of my 1999 Olds Bravada. We didn't bleed the brakes because we didn't feel that we had compromised them. Now the brakes are dragging and it seem

Replace the calipers my friend. Corrosion on the caliper pistons is holding the brakes on causing the drag. That rubber boot over the piston doesn't seal from condensation and makes surface rust/corrosion and won't allow the pistons to release all pressure.

Sep 25, 2014 | 1999 Oldsmobile Bravada

1 Answer

Having trouble bleeding brakes on 1997 olds bravada. bled all four still pedal goes to floor. any suggestions?

Are the rotors worn? Worn rotors and new pads will sometimes cause this. The pad sits across the ridges and no matter how much you bleed the system the pedal just wont stiffen up. (See diagram. A - New pads, B - Rotor, C - Ridge)
If you did not install new pads you may also want to check the master cylinder seals. First bleed the system at the pipes that connect to the master. If the rotors are ok, you've bled the master cylinder and the problem persists then replace the seals or the complete master cylinder.


Aug 18, 2010 | 1997 Oldsmobile Bravada

2 Answers

Break light is on fluid is fine no leaks and the

seems like you have air in the lines need to bleed the brakes

Feb 28, 2010 | 2000 Oldsmobile Bravada

2 Answers

2000 olds bravada rear brakes are draging. changed brake hose's to calupers and the center hose as well. with new brake and rotors still draging not sure what to do next.

I also have this problem on my 2000 Bravada - replaced all rotors and back calipers, brand new brake pads, new system and my rear caliper STILL chewed up a brand new brake pad in one week down to the metal. Checking for an emergency brake issue at this point - if anyone has any suggestions about how to unhook the E Brake, please share!

Jan 13, 2010 | 2000 Oldsmobile Bravada

2 Answers

I have a 1998 bravada, I replaced all 4 rotors, pads and both rear caliper brackets, but the right rear brake is dragging. Do I need a new caliper and if so how do you bleed the brakes. Thanks Walt

id bleed them first best if u have two people while u are doing this on ths caliper top the will be a bleeder valve have someone pump brakes and hold them down as u turn the bleeder after brake ped goes to the floor tighten bleeder up and have them pump brakes back up when u loosen bleeder u should here air come out if not u are fine go to next wheel do same on all for wheels

Oct 23, 2009 | 1998 Oldsmobile Bravada

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides