Question about 1996 Ford F250 Crew Cab

Open Question

Wheel bearing hub assembly diagram - 1996 Ford F250 Crew Cab

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: 1996 ford f250 4 wheel drive truck

Item Part Number Description 1 N800794-S60 Bolt, M16-2.0 x 50 2 N601797-S2 Bolt, Caliper Mount M12-1.75 x 30 3 2C150 Pin Assembly 4 2C357 Disc Brake Caliper 5 1175 Seal 6 3423 Bearing 7 3105 Front Wheel Spindle 8 4221 Differential Bearing 9 4222 Differential Bearing Cup 10 1190 Wheel Seal 11 1102 Front Disc Brake Hub and Rotor 12 1102 Front Disc Brake Hub and Rotor 13 1197 Locknut 14 1B198 Lockwasher 15 1C245 Thrust Washer 16 35704 Dana Nut 17 2K004 Front Disc Brake Rotor Shield 18 2B292 Anchor Bracket 19 3130,
3131 Steering Knuckle9572fc0.gif

Posted on Aug 19, 2008

polarcycle
  • 1392 Answers

SOURCE: 2005 ford escape assembly diagram for the front axle

If they are sealed bearings, you will need a press to get them out. If they are bolt in, just remove the brake pads/rotors, then the axle nut, then the bolts holding the wheel bearing in. Install in reverse order.

Posted on Mar 07, 2009

michigan man
  • 3533 Answers

SOURCE: How to replace front wheel bearings on a 2001 Ford Escape 4X4

try "autozone.com" or your local library for diagrams and step by step instructions

Posted on Mar 08, 2009

wlightaul
  • 29 Answers

SOURCE: HUB ASSEMBLY

these links are to remove but assembly is reversed
Here is a writeup on removing 5-bolt auto hubs

http://danielphotography.us/bronco/manualhubs/

Here is a writeup on removing 3-bolt auto hubs

http://www.superford.org/vehicles/re...d=3749&s=14884

Here is a writeup on removing manual hubs

http://fullsizebronco.com/forum/showthread.php?t=5450

Posted on Nov 28, 2009

  • 3741 Answers

SOURCE: how to remove rear bearing hub

The bearing is already shot so disregard what you hear about loosening the hub nut before you jack the car up. If you are doing this in your backyard it is VERY important to jack and support the car properly....you won't be able to use the parking brake because you'll be taking the disc/hat off. So work smart and safe.----Remove hub cap. :---Spray PB Blaster or another good rust killer in the hub, and all the nuts you will be removing. That means the pinch bolts for the toe link and the upper ball joint, plus the nut. Also the nut on the bolt of the lower arm. --Break the lug nuts AND 36mm hub nut a 1/4 turn.--Jack up the car and support. Remove lug nuts, then tire.----Remove brake caliper and support it to prevent damage to hose....I hung mine from the coil spring...The metal brake line fit in between the coils very nicely.----Remove disc/hat.----Remove the 36mm hub nut (you need buy a new one...really) -----Use a hub puller to press the axle shaft in through the hub, just a little bit...to break the rust. JUST A LITTLE! YOU ARE JUST BREAKING THE RUST SO IT WILL COME APART EASIER LATER. Spray it again and move on. Remove puller for now. -----Remove the springs, and retainers from the parking brake and remove the parking brake shoes.----Remove the parking brake levers coming through the rubber bushing .----Remove the Nut and Pinch Bolt from the Upper Ball Joint (at 12 o'clock) MAKE SURE YOU PUT THIS SAME BOLT BACK IN WITH A NEW NUT. THIS BOLT IS A LITTLE LONGER THAN THE TOE LINK BOLT!----Note: The pinch arms are just a term for the design....the bolt goes through a split....when the bolt is tightened, it clamps on the part that is meant to be held. Separate carefully....don't damage boot. I actually drove a stubby screw driver through the pinch arms of the knuckle to free it.

Remove the Nut and Pinch Bolt from the Toe Link (at 7 o'clock)

Separate carefully....don't damage boot. I actually drove a stubby screw driver through the pinch arms of the knuckle to free it.

Support lower arm (I used a cinder block)

Remove nut and bolt through lower arm (at 6 o'clock)

The only thing holding you back now should be getting the hub / knuckle assembly off the axle shaft.

Attach your puller again to the hub and as you tighten it the hub / knuckle assembly should start coming off the axle shaft pretty easily....if it doesn't, spray it.

The hub must be pressed out of the bearing
The bearing must be pressed out of the knuckle.

The new bearing must be pressed into the knuckle.
The NEW hub must be pressed into the bearing.

I don't have a press and had a local machine shop do this part for $50.00

I didn't have all tools and had to buy a few.

24" breaker bar $20
36mm hub socket $17
Universal Hub Puller $ 21....AutoZone will buy back but I will keep
The other tools are just a couple of sockets and wrenches....I think 18mm.
A ball joint splitter....PB Blaster (I swear by this stuff)

You SHOULD replace the HUB and bearing. I got the hub and bearing at AutoZone for $121.....tools cost $58...Machine Shop was $50.

Total cost was about $230.....dealer wanted $750.
This will help. Thanks please keep updated.please please do rate the solution positively .thank you for using fixya

Posted on Mar 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We need a picture of a Front wheel bearing hub assembly or diagram


DUDE, GO TO AUTOZONE.....GET THE SHOP MANUAL...BUY IT, LOOK AT IT.....OR HAVE THE AUTOZONE PEOPLE PRINT YOU A DIAGRAM OF THE FRONT HUB ASSY.

Jul 29, 2014 | 1996 Ford F150 Regular Cab

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

I need a diagram on front hub and brake assembly for 1999 dodge 1 ton dually 2 wheel drive. the front brake rotor is warped i need to replace it


8–Stud Rotor
  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Sep 16, 2009 | 2000 Dodge Ram 3500

1 Answer

Need help replacing front hub


Here's the steps....getting some pics for you....hang on a minute or two.

Front Hub Removal & Installation To Remove:
  1. Remove steering knuckle.
  2. Using a suitable slap hammer, remove wheel hub assembly.
  3. Using a suitable bearing press, remove outer bearing, oil seal, outer bearing race and preload spacer.
  4. Remove inner oil seal, inner wheel bearing and inner bearing race.
NOTE: It is not necessary to remove dust cover (back plate).
To Install:
  1. Using a suitable bearing press, install bearing races in steering knuckle.
  2. Pack the bearings and hub area with lithium grease.
  3. Install inner bearing in steering knuckle.
  4. Lubricate lip of NEW inner seal and press seal into knuckle.
  5. Install preload spacer into bore.
  6. Install outer bearing into bore.
  7. Lubricate lip of NEW outer seal and press seal into knuckle.
  8. Using an appropriate tool, support inner wheel bearing and press wheel hub into knuckle with a force of 2500kg.
  9. Install NEW inner seal.
  10. Install knuckle assembly.

May 13, 2009 | 2004 Kia Rio

1 Answer

1996 ford f250 4 wheel drive truck


Item Part Number Description 1 N800794-S60 Bolt, M16-2.0 x 50 2 N601797-S2 Bolt, Caliper Mount M12-1.75 x 30 3 2C150 Pin Assembly 4 2C357 Disc Brake Caliper 5 1175 Seal 6 3423 Bearing 7 3105 Front Wheel Spindle 8 4221 Differential Bearing 9 4222 Differential Bearing Cup 10 1190 Wheel Seal 11 1102 Front Disc Brake Hub and Rotor 12 1102 Front Disc Brake Hub and Rotor 13 1197 Locknut 14 1B198 Lockwasher 15 1C245 Thrust Washer 16 35704 Dana Nut 17 2K004 Front Disc Brake Rotor Shield 18 2B292 Anchor Bracket 19 3130,
3131 Steering Knuckle9572fc0.gif

Jun 11, 2008 | 1996 Ford F250 Crew Cab

Not finding what you are looking for?
1996 Ford F250 Crew Cab Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...