Question about 2009 Nissan Murano LE

Open Question

Where is fuse for backup camera

Camera is displayed intermittently when put in reverse. Some times it is there, sometimes it will just display the map.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda crv reversing camera not working how can i check it


Do you see anything on the screen? Does the screen switch to display the camera and just comes up blank? Is there any message?
It's possibly a broken wire. You would have to access the wiring to check for voltage at the camera.
Make sure your backup lights come on when in reverse. Some systems often use the voltage to the backup lights to activate the camera. If the switch is messed up and the lights don't come on, it might be the problem.

May 09, 2017 | Honda Cars & Trucks

1 Answer

My rear view mirror camera quit working I checked the fuse it's good the backup lights work.Help


Circuit/System Description
When the transmission is placed into REVERSE, a 12 volt signal is sent to the rearview camera image display module indicating that camera operation is requested. The rearview camera image display module then supplies ignition voltage and ground to the rear vision camera. The rear vision camera sends video information through the rearview camera image display module to the inside rearview mirror through a video signal + and a video signal - circuit. A grounded shielding also wraps the video signal circuits to reduce electronic interference which may degrade the video signal and cause a distorted or otherwise degraded image.

Rearview Camera Image Display Module (UVC)
In the instrument panel behind the driver side knee bolster to the right of the steering column
Do you know how to do electrical testing ?

Rear Vision Camera System Does Not Display
Ignition OFF, disconnect the harness connector at the rear view camera image display module.
Test for less than 1.0 ohm between the ground circuit terminal 3 and ground.
? If greater than the specified range, test the ground circuit for an open/high resistance.
Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 2 and ground.
? If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
Ignition ON, park brake applied, vehicle in REVERSE, verify that a test lamp illuminates between the control circuit terminal 1 and ground.
? If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
Ignition OFF, connect the harness connector at the rear view camera image display module. Disconnect the harness connector at the rearview camera.
Ignition OFF, test for less than 1.0 ohm between the ground circuit terminal B and ground.
? If greater than the specified range, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the rear view camera image display module.
Ignition ON, park brake applied, vehicle in REVERSE, test for 5.8-6.2 volts between the 6-volt reference circuit terminal A and ground.
? If less than the specified range, test the 6-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the rear view camera image display module.
? If greater than the specified range, test the 6-volt reference circuit for a short to voltage. If the circuit tests normal, replace the rear view camera image display module.
Ignition OFF, disconnect the harness connector at the rear view camera image display module.
Test for less then 1 ohm between the shield ground circuit terminal 10 at the rear vision camera display module harness connector and terminal D at the rear vision camera harness connector.
? If greater than the specified range, test the shield ground circuit for an open/high resistance.
Ignition ON, test for less than 1 volt between the signal circuit terminal 9 and ground.
? If greater than the specified range, test the signal circuit for a short to voltage.
Test for infinite resistance between the signal circuit terminal 9 and ground.
? If not the specified value, test the signal circuit for a short to ground.
Test for less then 1 ohm between the signal circuit terminal 9 at the rear vision camera display module harness connector and terminal C at the rear vision camera harness connector.
? If greater than the specified range, test the signal circuit for an open/high resistance.
Ignition OFF, disconnect the harness connector at the inside rearview mirror.
Ignition ON, test for less than 1 volt between the following signal circuits at the inside rearview mirror harness connector and ground:
• Video + signal circuit terminal 6
• Video - signal circuit terminal 7
Test for infinite resistance between the following signal circuits at the inside rearview mirror harness connector and ground:
? If greater than the specified range, test the signal circuit for a short to voltage.
• Video + signal circuit terminal 6
• Video - signal circuit terminal 7
? If greater than the specified value, test the signal circuit for a short to ground.
Test for less then 1 ohm between the following signal circuits:
• Signal circuit terminal 12 at the rearview camera image module and terminal 6 at the inside rearview mirror.
• Signal circuit terminal 11 at the rearview camera image module and terminal 7 at the inside rearview mirror.
? If greater than the specified range, test the signal circuit for an open/high resistance.
If all circuits test normal, test or replace the rear vision camera.
Ignition ON, park brake applied, vehicle in REVERSE, verify a clear rear vision image is displayed on the radio.
? If a clear rear vision image is not displayed, test or replace the inside rearview mirror

Feb 21, 2016 | 2009 Hummer H3

1 Answer

When put in reverse the image is up side down.


How to Reverse the Image on Backup Camera eHow

EVERYTHING YOU NEED TO KNOW ABOUT REAR VIEW CAMERAS

After installing a backup camera on your vehicle, you need to reverse the image so that the image on the screen matches that of your rear-view mirror. The orientation must match so that the driver doesn't get confused with two conflicting images. The nature of the camera's technology is that its image will be recorded un-reflected, but the mirror will display a reflected image. Fortunately, the engineers who designed back-up cameras thought of this and created simple controls for you to change the orientation.

Read more : http://www.ehow.com/how_6641139_reverse-image-backup-camera.html

Jan 12, 2016 | 2011 Lincoln MKX

1 Answer

Backup camera working intermittently


You are better off contacting the dealership to have these items looked at. Depending on warranty, it may be a covered item. And if this issue results in a problem with the display and not the camera, many of today's newer cars have these systems VIN programmed, which will put you in the dealership anyway

Dec 02, 2014 | 2011 Hyundai Elantra Limited

2 Answers

HOOKING UP BACKUP CAMERA


Hi Jim
You have to connect the negative to the vehicle body, and the positive to the reverse light wire.
this way the camera will comes ON when you put the selector in reverse.
Good Luck

Apr 09, 2014 | 2007 GMC Sierra 1500

2 Answers

Backup camera does not show any display. the warning light comes on but but the screen is black.


The camera at the rear end is not feeding video back to your screen or the screen is dead.

Nov 24, 2013 | 2007 GMC Yukon XL Denali

1 Answer

2011 chrysler town and country back up camera display not working


I have this problem with the backup camera, the dealership is telling me that the problem is in the TIPM (Totally Integrated Power Module). I am guessing there is a circuit board with a relay that went bad. They are telling me that the part is over $1000. I am going to check it out myself to be sure before fixing this.

Dec 22, 2012 | 2011 Chrysler Town and Country

1 Answer

2008 nissan armada backup camera wont work


make sure your backup lights are coming on. if the backup lights are working when in reverse then most likely you have a bad camera or loose connection. also may want to check for power to the camera ( fuses/circut).

Jul 30, 2011 | 2008 Nissan Armada

1 Answer

The multi information display prewired for a backup camera? Toyota venza 2009 v6


yes, but if installed it only works in reverse. When remove from reverse it goes back to display

Mar 24, 2010 | 2009 Toyota Venza

Not finding what you are looking for?
2009 Nissan Murano LE Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...