My 2008 lean fuel bank 1 - 2010 Peugeot 308 CC

Bank 1 is generally the cylinder bank closest to the firewall. Bank 2 is the one closest to the radiator.
Sensor 1 is the one in the exhaust manifold.

If the OBD code says it is running lean, you find it is covered in black soot when you remove it. With the new one in, you may get a running lean code as it is burning the soot out. Reset the code, it is a false positive. Happened to me last week.

https://www.google.com/search?q=sensor+1+bank+2+on+a+2008+saturn+vue+3.5l+v6+location

..

P0171 ; Fuel Trim System Lean (Bank 1)
P0174; Fuel Trim too Lean (Bank 2)
fuel trim is system to modify injector pulse if system go lean it will go rich when the system is too much lean and is max.rich it code
look for 02 sensor bank 1 and 2 data
hope it helps

P1100 Manifold Absolute Pressure Sensor Range/Performance
P1102 Manifold Absolute Pressure Sensor Circuit Low Input
P1103 Manifold Absolute Pressure Sensor Circuit High Input
P1123 Lang Term Fuel Trim Adaptive Too Lean
P1124 Long Term Fuel Trim Adaptive Too Rich
P1127 Long Term Fuel Trim Multiplier Too Rich
P1128 Long Term Fuel Trim Multiplier Too Lean
P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)
P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)
P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)
P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)
P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)
P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)
P1372 Segment Time Incorrect
P1400 Manifold Differential Pressure Sensor Circuit
P1440 EVAP System Vent Solenoid Circuit
P1443 EVAP System Fault (Fuel Tank Cap Missing)
P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)
P1511 Idle Control Valve Command Signal Shorted (Coil 2)
P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)
P1521 Power Steering Switch Input Circuit
P1529 Customer Snapshot Request VIA CAN
P1552 Idle Air Control Valve Closing Coil Circuit Shorted
P1553 Idle Air Control Valve Closing Coil Circuit Open
P1586 Encoding Signal Circuit Not Rationale
P1602 Serial Communication Fault with Transmission Control Unit
P1605 Rough Road Sensor Circuit
P1606 Rough Road Sensor Circuit Not Valid
P1611 MIL Request Signal Circuit Low Input
P1613 ECU Self-Test Failed
P1614 MIL Request Signal Circuit High Input
P1616 Main Relay Fault
P1623 Diagnostic Lamp Power Stage Fault
P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit
P1625 Cooling Fan Relay High Circuit
P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault
esta codigo no lo existe in hyundai codigos

I've come across these codes before. In almost every case there was an air leak in the intake air hose (hose between the engine air filter & the throttle body). Inspect this hose & tubes attached to it. This is especially true when the lean code includes the comment 'at idle'
P2187 - System too lean at idle Bank 1
P0174 - System too lean Bank 2
P2189 - System too lean at idle Bank 2
P2195 = HO2S Signal Biased/Stuck Lean (Bank 1 Sensor 1)
P2270 = HO2S Signal Stuck Lean (Bank 1 Sensor 2)
P2272 = HO2S Signal Stuck Lean (Bank 2 Sensor 2)

P2187 & P2189 = In order to provide the best possible combination of drivability, fuel economy and emission control, the PCM uses a closed loop air/fuel metering system. The PCM monitors the HO2S signal voltage and adjusts fuel delivery based in closed loop fuel control. Changes in fuel delivery will be indicated by the long-term and the short-term fuel trim values. The ideal fuel trim value is around 0%. The PCM will add fuel when the HO2S signal is indicating a lean condition. Additional fuel is indicated by fuel trim values that are above 0%. The PCM will reduce fuel when the HO2S signal is indicating a rich condition. Reduction in fuel is indicated by fuel trim values that are below 0%. The DTC relevant to fuel trim will be set when the amount reaches excessive levels because of a lean or rich condition

P0171 = system too lean bank 1
P0174 = system too lean bank 2

The fuel/air mixture is too lean for the entire engine. The fuel pump pressure could be too low. The fuel pump pressure regulator could be at fault. There could be an air leak downstream of the MAF sensor. MAF sensor (hot wire type) could be dirty. Check for intake manifold vacuum leaks. The engine coolant temp sensor and/or the intake air temp sensor could be faulty (stuck at full hot mode).

iam posting the hyundai code list i have that the vehicle manufacturer lists

P1100 Manifold Absolute Pressure Sensor Range/Performance

P1102 Manifold Absolute Pressure Sensor Circuit Low Input

P1103 Manifold Absolute Pressure Sensor Circuit High Input

P1123 Lang Term Fuel Trim Adaptive Too Lean

P1124 Long Term Fuel Trim Adaptive Too Rich

P1127 Long Term Fuel Trim Multiplier Too Rich

P1128 Long Term Fuel Trim Multiplier Too Lean

P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)

P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)

P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)

P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)

P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)

P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)

P1372 Segment Time Incorrect

P1400 Manifold Differential Pressure Sensor Circuit

P1440 EVAP System Vent Solenoid Circuit

P1443 EVAP System Fault (Fuel Tank Cap Missing)

P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)

P1511 Idle Control Valve Command Signal Shorted (Coil 2)

P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)

P1521 Power Steering Switch Input Circuit

P1529 Customer Snapshot Request VIA CAN

P1552 Idle Air Control Valve Closing Coil Circuit Shorted

P1553 Idle Air Control Valve Closing Coil Circuit Open

P1586 Encoding Signal Circuit Not Rationale

P1602 Serial Communication Fault with Transmission Control Unit

P1605 Rough Road Sensor Circuit

P1606 Rough Road Sensor Circuit Not Valid

P1611 MIL Request Signal Circuit Low Input

P1613 ECU Self-Test Failed

P1614 MIL Request Signal Circuit High Input

P1616 Main Relay Fault

P1623 Diagnostic Lamp Power Stage Fault

P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit

P1625 Cooling Fan Relay High Circuit

P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault

code P1128 02 sensor bank 1 lean
code P1129 02 sensor bank 1 lean to limit
code P1133 02 sensor bank 2 lean
code P1134 02 sensor bank 2 lean to limit

fuel system is lean.

P0313 - Misfire Detected with Low Fuel
P0174 -System too Lean (Bank 2).
P0171 -System too Lean (Bank 1).

P0171 and P0174 mean "system too lean" for banks 1

take of the fuel filter and blow it out. i had the same problem with a 2008 ford f150 5.4 v8.