Question about Cars & Trucks

1 Answer

What does map sencor do andhow to test it 1998 olds cutlass

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

Usually the map sensor is on top of the intake near the firewall. The sensor measures manifold vac.
You would use a scanner to "watch" the sensor reading as the vac changes.

Posted on Apr 28, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bschilz
  • 2049 Answers

SOURCE: replace serpentine belt 1998 olds cutlass

Here's a link to a series of videos that will explain how to change the serpentine belt.

http://www.wonderhowto.com/how-to/video/how-to-change-a-serpentine-belt-on-your-car-39904/

Here is a diagram of the belt routing which will help you put the belt back on correctly...
18841fa.jpg

Posted on Dec 05, 2009

toneman2121
  • 775 Answers

SOURCE: where is the crankshaft osition sencor located on

the sensor is located on the front, lower portion of the engine, along the circumference of the crankshaft pulley. the large pulley at the bottom center of the engine

Posted on Apr 10, 2010

  • 14036 Answers

SOURCE: how do i replace the

CRANKSHAFT SENSOR LOCATED ON THE SIDE ENGINE BLOCK NEAR THE OIL PAN.JUST DISCONNECT ELECTRICAL CONNECTOR GOING TO SENSOR . AND REMOVE SMALL BOLT HOLDING IT IN PLACE THEN REMOVE SENSOR.

Posted on Jun 10, 2011

  • 3640 Answers

SOURCE: Need to add transmission fluid to a 1998 Olds Cutlass

on the 98 cutlass if its a 3.1, no dipstick, all other engine models do. on the 3.1 there is no dipstick on it.on these models, it is not necessary to check the fluid at regular intervals.if leaks or other problems lead you to think fluid is low heres how to check it. WARNING the procedure is dangerous, it is best left to a professional with a safe lifting apparatus.the vehicle must be kept level while being safely raised high enough for access to the check plug on trans axle. If your 98 Cutlass has a 3.1 liter V-6 engine, the transmission is not equipped with a dipstick; this transmission requires a special procedure and equipment to accurately check the fluid, which should be done by a qualified service technician. All other engines have a dipstick that is used to check the fluid level and condition. for more info call the olds garage!

Posted on Oct 27, 2011

johnf1aresti
  • 1116 Answers

SOURCE: nissan pathfinder 1998 code p0325 what sencor is it there are 4 Sencors ???

It is the knock sensor. But before you do anything first check the vacuum line which is on the front right tire on the rear side of the tire where small hose from charcoal canister up over the shock to the purge valve. That vacuum hose from the purge valve connected to a metal hose and then the metal hose connected back to a rubber hose on the purge valve. that metal hose because it gets rusted cause a leak causing Injector 2 to missfire.

Posted on Aug 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the crank shaft position sencor on a 92 olds cutlass 2.3


CRANKSHAFT SENSOR LOCATED ON THE SIDE ENGINE BLOCK NEAR THE OIL PAN.JUST DISCONNECT ELECTRICAL CONNECTOR GOING TO SENSOR . AND REMOVE SMALL BOLT HOLDING IT IN PLACE THEN REMOVE SENSOR.

Jun 10, 2011 | Oldsmobile Cutlass Ciera Cars & Trucks

1 Answer

How do i solve code 33 on olds cutlass supreme?


I believe this is the MAP sensor code. If so check your MAP sensor vacuum hoses and electrical connections at your ECM. You may need to replace your MAP sensor.

Nov 23, 2010 | 1989 Oldsmobile Cutlass Supreme

2 Answers

1991 olds cutlass calais 2.5 engine ran the self dignostics and got code 33 need to what code 33 is.


It's the maf/map sensor circuit.
maf--- mass air flow sensor
map--- manifold absolute pressure.--- check the small vaccum hose from the map sensor to the source, could be brittle and leaking air.
Have both the map and maf sensor checked for proper voltage, one or both could be bad. A repair shop shouldn't charge much to do that.

May 05, 2010 | 1991 Oldsmobile Cutlass Calais

1 Answer

Where is the crankshaft osition sencor located on a 99 olds cutlass


the sensor is located on the front, lower portion of the engine, along the circumference of the crankshaft pulley. the large pulley at the bottom center of the engine

Apr 10, 2010 | 1999 Oldsmobile Cutlass

1 Answer

Replace serpentine belt 1998 olds cutlass


Here's a link to a series of videos that will explain how to change the serpentine belt.

http://www.wonderhowto.com/how-to/video/how-to-change-a-serpentine-belt-on-your-car-39904/

Here is a diagram of the belt routing which will help you put the belt back on correctly...
18841fa.jpg

Dec 05, 2009 | 1998 Oldsmobile Cutlass

2 Answers

My dodge stratus stalled and wont start


Check the MAP sensor. This measures the air pressure in the maniforld. It is commonly mounted on a fender, low cost and easy to replace.

To test, unplug the electrical connection from the MAP sensor. If it starts, replace the sensor.

Jul 10, 2009 | 1996 Dodge Stratus

1 Answer

93 olds cutlass ciera-it bucks and jumps and will die especially on turns. Sometimes hard to restart. May drive several days with no problem and then it will start up again. Any ideas? Has had a new MAP...


When was the last time the fuel filter was chg.? If you can't remember or thats not an issue, than its time to do a fuel pressure test to determine if pump is weak, or on its way out.

Apr 18, 2009 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Map Sensor Location


back of the intake please leave feed back thanks

Sep 18, 2008 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Olds Cutlass GL 1998


Are the battery cables corroded or otherwise no making a good connection? Clean them with a cable end cleaning tool avail at any auto parts store for around $5.00 and try it again, I bet the that is the issue, also charge the battery and have it tested at Kragen, they do it for free.

Sep 16, 2008 | 1998 Oldsmobile Cutlass

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...