Question about Jeep Cherokee

1 Answer

Where is crankshaft sensor on - Cherokee Jeep Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers




  • Locate the crankshaft position sensor on
    the driver side of the bell housing, about half way down. It is secured with two
    7/16-inch bolts and has a cable that runs up and onto the
    engine.

  • 2


    Remove the two 7/16-inch bolts from the bracketWhere is crankshaft sensor on - icon1.png holding the
    CPS. A socket with extension or an open end wrench can be used, depending on
    what works best for you.





  • Sponsored Links



  • 3


    Move up the cable about 6 to 8 inches and
    you will find a clip that holds the cable against the bell housing of the Jeepicon1.png. Remove the
    cable from the clip.

  • 4


    Trace the cable from the CPS to the the top
    of the engine and locate the weather-proof connector where it plugs into the
    main wiring harness. Unplug the connector, being careful not to break the tab on
    the connector.

  • 5


    Remove the old CPS and cable from the Jeep.
    Install the new CPS in the location that you removed the old one from, using the
    two 7/16-inch bolts. Route the cable from the new CPS up to the clip on the bell
    housing and install the cable under it.

  • 6


    Route the remaining cable up through the
    engine compartment and plug in the weather-proof connector. The connector should
    only go in one way and it should click in when properly
    seated.


  • Read more: How
    to Replace Crank Sensors in a Jeep Cherokee ' eHow.com
    http://www.ehow.com/how_5728720_replace-crank-sensors-jeep-cherokee.html#ixzz2Rlgf329K

    Posted on Apr 28, 2013

    Ad

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
    click here to download the app (for users in the US for now) and get all the help you need.
    Goodluck!

    Posted on Jan 02, 2017

    Ad

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Is my crank sensor faulty, symptoms of a faulty crank sensor 2000 Rodio 3.2 L


    Intermittent stalling. Another symptom commonly associated with a problematic crankshaft position sensor is intermittent stalling. If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall.

    Symptoms of a Bad Crankshaft Sensor ' DoItYourself.com

    www.doityourself.com/stry/symptoms-of-a-bad-crankshaft-sensor
    This makes it an important part of your engine system; a bad crankshaft sensor affects not only the engine speed but also the fuel efficiency of your car.

    7 Crankshaft Position Sensor Failure Symptoms ' DoItYourself.com

    www.doityourself.com/stry/7-crankshaft-position-sensor-failure-symptoms 1 - Check Engine Light. This can be frustrating as the check engine light can obviously turn on for many different things. 2 - Cylinder Misfiring. 3 - Acceleration Hesitation. 4 - Intermittent Starting. 5 - Engine Vibrations. 6 - Backfiring and Stalling. 7 - Irregular Car Function.

    Warning Signs of a Bad Crankshaft Position Sensor ' DoItYourself.com

    www.doityourself.com/stry/warning-signs-of-a-bad-crankshaft-position-sensor Ignoring the symptoms of a bad crankshaft position sensor will result in rapid wear and tear of the various parts of the engine and will quickly lead to engine ...

    Symptoms of a Bad or Failing Crankshaft Position Sensor ...

    https://www.yourmechanic.com/.../symptoms-of-a-bad-or-failing-crankshaft-position-... Jan 6, 2016 - Intermittent stalling. Another symptom commonly associated with a problematic crankshaft position sensor is intermittent stalling. If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall. ‎Crankshaft sensor · ‎Car is stalling Inspection · ‎How Long Does a Crankshaft ...

    Symptoms of a Bad Crankshaft Sensor - Buy Auto Parts

    www.buyautoparts.com/howto/symptoms-of-a-bad-crankshaft-sensor.htm Problems you will run into when your crankshaft position sensor has gone bad.

    symptoms of faulty crank sensor Google Search

    Sep 22, 2017 | Cars & Trucks

    1 Answer

    Where is the crankshaft position sensor?


      Pontiac G6 Crankshaft Position Sensors - AutoZone

      www.autozone.com/1/.../pontiac-g6-crankshaft-position-sensor...
      AutoZonePontiac G6 Crankshaft Position Sensors including Crankshaft Position Sensor - Duralast (SU8213), Crankshaft Position Sensor - Duralast (SU9540), Crankshaft ... images for pontiac g6 crankshaft position sensor

    Oct 28, 2015 | 2006 Pontiac G6

    1 Answer

    Troubleshoot crank position sensor location


    For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
    ----------

    How to test Crankshaft Position CKP Sensor?

    ---------------
    Crankshaft Position Sensor Operation?

    ----------------
    Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
    ----------
    GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

    ------------
    These details will help.
    Thanks.

    Nov 25, 2012 | 2000 Cadillac Escalade

    1 Answer

    Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


    crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

    Nov 14, 2011 | 2000 Nissan Xterra

    1 Answer

    Need to replace the crankshaft position sensor


    REMOVAL & INSTALLATION
    1. Disconnect the negative battery cable.
    2. Remove the serpentine drive belt from the crankshaft pulley.
    3. Raise and safely support the vehicle.
    4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
    5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
    6. Remove the crankshaft balancer, using a puller if necessary.
    7. For 1992-99 vehicles, remove the CKP sensor shield. Fig. 1: If so equipped, remove the crankshaft position sensor shield 89634g95.gif

    8. Unplug the sensor electrical connector.
    9. For 1987-91 vehicles, perform the following:
      1. Remove the sensor and pedestal from the block face.
      2. Remove the sensor from the pedestal.
    10. For 1992-99 vehicles, remove the sensor from the block face. To install:
      1. For 1987-91 vehicles, perform the following:
      2. Loosely install the crankshaft sensor on the pedestal.
      3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
      4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm). Fig. 2: Position the crankshaft sensor tool on the crankshaft 89634g76.gif
        Fig. 3: Insert the crankshaft sensor tool into the harmonic balancer 89634g75.gif

      5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
      6. Remove the special tool.
      7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
    11. For 1992-99 vehicles, install the CKP sensor on the block.
      1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
      2. Install the crankshaft position sensor shield.
      3. Attach the sensor electrical connector.
    12. Install the balancer on the crankshaft.
    13. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 76°rotation.
    14. Install the inner fender shield and the right tire and wheel assembly.
    15. Carefully lower the vehicle.
    16. Install the serpentine belt.
    17. Connect the negative battery cable.
    prev.gif next.gif

    Oct 29, 2010 | 1999 Oldsmobile 88

    2 Answers

    I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


    The crank sensor is located on the engine near the flywheel axis of the crankshaft.

    Crankshaft Position Sensor Removal & Installation To Remove:
    Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
    Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
    Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
    NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
    1. Disconnect the negative battery cable.
    2. Raise and safely support the vehicle.
    3. Disconnect the crankshaft position sensor electrical connector.
    4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
    To Install:
    NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
    1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
    2. Connect the crankshaft position sensor electrical connector.
    3. Lower the vehicle.
    4. Connect the negative battery cable.
    prev.gif next.gif

    Jul 31, 2010 | 1996 Plymouth Grand Voyager

    1 Answer

    Where is the crankshaft sensor on a v6 2000 chrystler sebring


    CRANKSHAFT POSITION SENSOR - 2.5L
    REMOVAL
    Remove speed control servo from driver's side strut tower.
    Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
    Pull crankshaft position sensor straight up out of the transaxle housing.
    (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
    INSTALLATION - ADJUSTABLE
    All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.

    NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer

    Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
    Connect crankshaft position sensor electrical connector to the wiring harness connector.
    Attach connector to heater tube bracket.
    Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

    May 22, 2010 | 1998 Chrysler Sebring

    1 Answer

    Jsut want to know where crankshaft position sensor


    Hi!!

    here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

    Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


    2.3L Engine


    The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

    0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


    3.0L Engine


    The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

    0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

    The cost of the sensor is $23 bucks at AutoZone.

    If helpful, click below

    Apr 15, 2010 | 2002 Ford Escape

    1 Answer

    I CANT LOCATE CRANK POSITION SENSOR


    7X Crankshaft Position (CKP) Sensor
    Lower rear of engine
    4
    25
    --
    24X Crankshaft Position (CKP) Sensor
    Right hand side of engine, at end of crankshaft, behind harmonic balancer
    7X Crankshaft Position (CKP) Sensor
    Lower rear of engine
    4
    25
    --
    24X Crankshaft Position (CKP) Sensor
    Right hand side of engine, at end of crankshaft, behind harmonic balancer
    Right hand side of engine, at end of crankshaft, behind harmonic balancer

    Apr 12, 2009 | 1995 Chevrolet Monte Carlo

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    239 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...