Question about Cars & Trucks

Open Question

Westinghouse wrh908i fascia - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace rear parking sensor


You have to take bumper cover off .
Remove rear bumper fascia. Refer to Rear Bumper Fascia Replacement . Disconnect electrical from the rear object sensor. Lift the locking tabs on the housing and remove the rear object sensor.
Preliminary Procedure
  1. Remove the compartment sill plate. Refer to Rear Compartment Sill Trim Plate Replacement .
  2. Remove rear wheel liners. Refer to Rear Wheelhouse Panel Liner Replacement .
1
Rear Fascia Push Pin Retainers (Qty: 2)
2
Rear Fascia Nuts (Qty: 4)
Tighten
10 N?·m (89 lb in)
3
Rear Fascia Bolts (Qty: 2)
4
Rear Fascia Bolts (Qty: 6)
5
Rear Fascia
Tip
?€¢
Energy absorber and fascia are removed together. Cannot be separate on vehicle.


?€¢
Disconnect the electrical connectors.

Dec 22, 2015 | 2006 Cadillac DTS

1 Answer

How do I replace my rear bumper on my 04 pacifica


  1. Open liftgate.

133387935 Fig. 12

  1. Remove two push pin fasteners per side at the liftgate tower area (Fig. 12).
  2. Hoist and support vehicle with safety stands, as necessary.

133387936 Fig. 13

  1. Disconnect the park assist wire connector under the vehicle and the push pin fasteners attaching wire harness under the vehicle (Fig. 13)
  2. Remove the four push pin fasteners attaching rear fascia to reinforcement bumper.
  3. Remove two screws (each side) attaching fascia to rear fascia bracket in the wheelhouse.
  4. Remove the screw on each side attaching the upper fascia in the tail lamp bucket area.
  5. Remove rear fascia from vehicle by lifting sides of fascia up and outboard to release from rear fascia brackets.
  6. Place fascia on a clean surface.

133387937 Fig. 14

  1. Remove park assist sensors, if necessary (Fig. 14).

133387938 Fig. 15

  1. Remove spring clips attaching upper and lower fascia together (Fig. 15).
  2. Using a trim stick release locking tabs and separate the upper and lower fascia.

133387939 Fig. 16
133387940 Fig. 17

  1. Remove move the bright chrome molding from the upper fascia (Fig. 16). Using a trim stick, starting at the out edge of the fascia release the locking tabs (Fig. 17). Grip the molding and pull outward from the fascia while releasing the locking tabs.
  2. Remove molding from fascia.
INSTALLATION

  1. Place bright chrome molding in position on the upper fascia.

133387941 Here you go1_9_2012_2_48_31_am.gif

Jan 06, 2012 | 2004 Chrysler Pacifica

1 Answer

How to remove the rear bumper cover on a pontiac 2004 grand prix


  1. Open the trunk.
  2. Remove the rear compartment sill plate. (Trim round the back edge of the trunk)
  3. Pull the left and right compartment side trim panels down to access the fascia bolts and nuts.
  4. Remove the tail lamps.
  5. Remove the fascia bolts and nuts from the rear bumper fascia 1 nut 1 bolt on each side near tail lights.
  6. Remove the push-in retainers from the top edge of the fascia.(4 plastic circles, pull up on center of cirle with screwdriver
  7. Raise and support the vehicle.
  8. From underneath Remove the push-in retainers from the rear bumper fascia (one on each side I think)
  9. Remove the fascia bolts from the rear bumper fascia. on on each side from, up where the facia connects to the quater panel)
  10. Remove the rear bumper fascia from the vehicle

Apr 14, 2011 | 2004 Pontiac Grand Prix

1 Answer

I am looking for a diagram of the bumper assembly for a 2004 Chrysler town & country.


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


  1. Release hood latch and open hood.
  2. Remove the headlamp assemblies.
  3. Hoist vehicle and support with safety stands.
  4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
  5. Remove front wheels.
  6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Fig. 1 133387737
Fig. 2 133387738

  1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
  2. Disconnect fog lamp wire connectors, if necessary.
  3. Lower vehicle.
  4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
  5. Remove bumper fascia from vehicle.
INSTALLATION


  1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
  2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
  3. Hoist vehicle and support with safety stands.
  4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
  5. Install front wheelhouse splash shields fasteners.
  6. Install front wheels.
  7. Connect fog lamp wire connectors, if necessary.
  8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
  9. Lower the vehicle.
  10. Install the headlamp assemblies.

Jan 02, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    How do I replace dashboard heater light? The glowing lights that indicate direction of air flow.


    Heater light bulb, and all other bulbs for the air conditioning buttons, are on the same mini panel, and attached to the back of the radio front fascia. To dismount this fascia, you need 1) To pry out (no screws) the clock 2) Unscrew the one screw that holds the top of the fascia (screw is hidden behind clock) 3) Unscrew the two screws at the bottom of the fascia 4) Disconnect all connectors from the back of the fascia 5) Look for the burnt minibulb.
    You could replace the bulb without disconnecting, but the cables are short, and the possibilities of marring your dashboard are high.

    Jun 19, 2010 | 1999 Honda Accord

    1 Answer

    How do you remove the air filter box on a 2001


    REMOVAL
    Release hood latch and open hood.
    Access Rubber Grommet
    Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners.
    Fastener Locations

    Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield.
    Remove Push In Fasteners
    Remove the push pins attaching the fascia to the upper radiator closure panel.
    Headlamp Jack screws

    Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s).
    Roll Fascia Forward

    Roll fascia forward to clear way for headlamp housing removal.
    Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    Remove Headlamp Housing

    INSTALLATION
    CAUTION : Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

    Place headlamp housing into position.
    Connect wire connector to lamp socket(s)
    Verify headlamp and signal lamp operation.
    Install jackscrews to attach headlamp housing to crossmember.
    Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    Install nut on fascia stud through the splash shield access hole.
    Verify headlamp operation and alignment


    Nov 03, 2009 | 2001 Chrysler 300M

    1 Answer

    I need info on how to replace the headlamp bulbs on my 2008 Chevy Malibu, can you help.


    The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.
    1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
    2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
    3. You will also need to remove some of the fasteners at the front of the inner wheel well.
    4. The Front Bumper Fascia is the plastic cover over your front bumper.
    5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.

    Oct 27, 2009 | 2008 Chevrolet Malibu

    1 Answer

    Change headlight


    hello. below is the procedure for removal of the headlamp for bulb replacement. to access the headlamp you will need to remove the bumper fascia. http://gsi.xw.gm.com/image_en_us/gif/000/001/725/1725371.gif Callout Component Name 1 Front Compartment Sight Shield Plastic Retainers (Qty: 6) 2 Front Compartment Sight Shields (Qty: 3) Tip Each front compartment sight shield is serviced separately as needed for repairs http://gsi.xw.gm.com/image_en_us/gif/000/001/728/1728611.gif Callout Component Name Preliminary Procedure Remove the front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement . 1 Front Fascia Extension Plastic Retainers (Qty: 5) 2 Front Fascia Extension http://gsi.xw.gm.com/image_en_us/gif/000/001/733/1733942.gif Callout Component Name Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedures Remove the front compartment sight shields. Remove both front bumper fascia extensions. 1 Front Bumper Fascia Reinforcement Nut (Qty: 2) Tighten 6 N·m (53 lb in) 2 Front Bumper Fascia http://gsi.xw.gm.com/image_en_us/gif/000/001/736/1736893.gif Callout Component Name Notice: Refer to Fastener Notice in the Preface section. Fastener Tightening Specifications: Refer to Fastener Tightening Specifications . Preliminary Procedure Remove the front bumper fascia. 1 Headlamp Nut (Qty: 1) Tighten 6 N·m (53 lb in) 2 Headlamp Bolts (Qty: 3) Tighten 6 N·m (53 lb in) 3 Headlamp Assembly

    Jun 13, 2009 | 2003 Cadillac CTS

    1 Answer

    How do you replace headlamp bulbs on 1999 chrysler 300


    You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
    Tell me if this works for you?
    HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
    REMOVAL
    1. Release hood latch and open hood.
    2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
    3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
    4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
    5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
    6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
    7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    8. Remove headlamp housing Remove Headlamp Housing
    INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.
    1. Place headlamp housing into position.
    2. Connect wire connector to lamp socket(s) and/or bulbs.
    3. Verify headlamp and signal lamp operation.
    4. Install jackscrews to attach headlamp housing to crossmember.
    5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    7. Install nut on fascia stud through the splash shield access hole.
    8. Verify headlamp operation and alignment

    Mar 27, 2009 | 1999 Chrysler 300M

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    18 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...