Question about 1997 Dodge Intrepid

Open Question

Turn signals replaced all fuses relays bulbs and the turn signals still do not work

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: turn signals wont work but flashers do

Hi.
On your 98 Dakota.
Is equipaded with a single Flasher.
If you replace all ready.
Check the FUSE # 10, 15 amp..
On the Fuse box. left side of Dash.
and the FUSE D 25, amp. On engine compartment Fuse box.
Check the proper funtion of the HAZARD switch.
Bacause if the Hazard switch is bad the turn signal don't will work. Match the OLD flasher with the New one.

If after of this still not work.
Remove the steering wheel cover, locate the Turn signal switch connector and with a TEST Light check power with the Key ON
12v. to the RED wire and PINK wire..
If you found 12v. check the connection with the switch.
If the connection is good. you will need to replace the turn signal switch.
But if you don't found 12v. You need to look a an open circuit.
And fix it..

I hope this help on your problem..
Thank you for use fixya...

Posted on Sep 01, 2008

Ad
  • 1150 Answers

SOURCE: turn signals and hazard lights quit working on 2001 dodge ram

The only thing left to investigate is the signal switch itself. The brake light system runs through the signal switch so it can effect both systems. Start with the simple, like, is a wire loose? Look at the base of the steering column. Check plugs and such. I believe you'll see it's in that part of the system.

Good Luck

Posted on Feb 27, 2009

LEFTY64
  • 69 Answers

SOURCE: where is the turn signal relay located on a 1995 dodge stratus?

Front seating area, driver side, under dash, under knee protector, mounted in multi-purpose fuse panel

Hope this helps

Lefty64

Posted on Apr 11, 2009

motor1258
  • 6674 Answers

SOURCE: 1993 Dodge Shadow...left turn signal won't flash

If you have trouble finding signal flasher, turn your right side blinker on, and follow clicking noise to flasher.

Posted on Apr 13, 2009

  • 1 Answer

SOURCE: Turn signals don't work.

rights turn signal will not shut off

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New flasher relay good fuse no four way flasher no turn signals


you need to check the bulbs holders and wiring even a blown bulb will not blow the fuse and an damaged wire or bulb holder will as it will make earth and live go together. there are also fuses for left side and right side turning lights cannot remember rating think they are 10amp.

Mar 19, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

04 Hyundai, Hazards Work But No Turn signals


Always check the bulbs first. Then check for power ant the bulb socket. If the fuses are ok( some have seperate fuses for right and left).......More than likely its a relay wich should be located on or near the fuse panel.The turn signal and hazards usualy have the same type of relay. Swap the turn signal and hazard relays. If the problem is then oposite of what you had before, then replace the relay....

Mar 29, 2013 | Cars & Trucks

1 Answer

1998 Dodge Durango flasher relays location


Turn on the Durango and check each of the four turn signals to make sure that the bulbs are not burned out. If you find one that has gone out, replace the bulb and retest the turn signals. When a bulb goes bad on this circuit, the resulting operation can mimic a bad flasher or one that is failing.

Locate the combination turn signal flasher and relay. It is on the left end of the driver's dash. Open the access door and view the collection of relays and fuses. At the left side of the mounting block is a larger flasher and relay. This is the combination turn signal flasher and relay.

Test the relay by placing you finger on the relay housing and activating the turn signal. If you have found the right one, you should feel a clicking as the turn signal blinks. Remove the relay, replace with the new relay and close the access door

.

Start the Durango and activate the turn signals to check that they each work. The light should turn on and should blink. Also, check the hazard lights to make sure they work.

Feb 11, 2012 | Dodge Ram 1500 Cars & Trucks

1 Answer

Turn signals wont work


This problem usually is either the relay, fuse, or bulbs. To know if it is/isn't the relay, with the car on, turn on the turn signal and listen for clicking. If you hear it, then the relay is working. If you don't hear it, then the relay needs to be replaced. Very rarely the wiring is the cause. To test the wiring, get access to the fuse box for the turn signals. Grab a multimeter, take out the fuse, then insert leads into the opposing slots. Turn the meter on to DC voltage mode, then turn on the car and flick the turn signal on. You should see spikes whenever the turn signal turns on. If you don't see spikes, then the wiring or the bulbs is dead. Replace all the bulbs, then run the test again and if the meter still doesn't spike, then you need to check all the wires for cracks or melting. If you have to replace wires, install the same gauge wire as was previously there. Use a wire stripper to get a good judge of the gauge.

Sep 01, 2011 | 2000 Dodge Durango

3 Answers

Turn signal does not work and all bulbs have been replaced


If the arrow light on the dash flashes, this means your flasher and multifunction switch are working, and your bulb, wiring to the bulb terminal, or bulb terminal are defective.

If the arrow light on the dash does not turn on, you will need a new multifunction switch(on the steering column, near the steering wheel)

If the arrow light on the dash comes on, but stays solid, you need a new flasher unit.

Mar 14, 2011 | 1997 GMC Jimmy

3 Answers

Blower motor and turn signals stopped working


CHECK BLOWER MOTOR FUSE AND RELAY.IF ALL IS GOOD.CHECK TO SEE IF BLOWER IS GETTING POWER.IF NOT.SWITCH IS BAD.IF YES REPLACE BLOWER MOTOR.IF TURN SIGNALS STOP WORKING.CHECK FUSE FIRST.IF FUSE LOOK GOOD. CHECK BULBS TO SEE IF THEY ARE BLOWN.IF BULBS LOOK GOOD PROBLEM COULD BE WORN OR CORRODED BULB SOCKETS OR.BAD GROUND.OR THE TURN SIGNAL SWITCH IS BAD.

Aug 24, 2009 | Plymouth Voyager Cars & Trucks

1 Answer

Dont have signal


Click the turn signal switch to either the right or left and get out and check if the BULB comes on but doesn't blink. Try both directions. Does the arrow for that direction also come on, on the dashboard instruments and stays on but not blink? That is a built in indicator that a filament has burned out in one of the bulbs. Try replacing the bulbs. Could also be the fuse for that circuit. Check fuse panel for that circuit. Could also be the turn signal relay. Replace with newer style relay.

Jul 15, 2009 | 1996 Geo Prizm

2 Answers

No turn signals, no tail lights and fuses are good


Replace the non-working tail light bulb. Try replacing the bulbs for the turn signals. If that doesn't work, replace the relay.

May 24, 2009 | 1995 Isuzu Rodeo

1 Answer

I can't locate the turn signal flasher


next step after replacing fuses is to check relays,receptacles themselves and bulbs youll need a multitester with dc volts setting
first remove relay and have them checked or check them your self by making sure power is coming out of relay wires once turn signal is active using multi tester at 20 dcv setting if power is coming out relay is good
then remove bulb from turn signal housing and test if power is coming into socket same setting if so replace bulbs

Feb 06, 2009 | 1997 Nissan Pathfinder

Not finding what you are looking for?
1997 Dodge Intrepid Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...