Question about 2005 Dodge Neon

1 Answer

Crank sensor were is the crank sensor and how hard to change

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 5,628 Answers

Crankshaft sensor is under crank pulley .

Posted on Apr 28, 2013


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not start


Clean the mass airflow sensor with a special spray cleaner meant for the job. Any other kind of cleaning spray will destroy the sensor..

Oct 25, 2016 | Cars & Trucks

1 Answer

2003 Nissan xterra...couple problems...timing belt just changed...knock sensor, crank shaft positioning sensor, distributor cap all changed...service engine soon light keeps coming on...took to...


Had same issue with (re: crank position sensor) on a 2002 Kia. Had all the same work done as you, only to find out with was one of those Kias with a manufacture defect in the block where the crankshaft keeper key slots to lock crankshaft in place in block. The block half of the slot had worn and the crank shaft itself kept slipping out of time. Is it throwing any codes? Gas pedal linkage may well just need a good cleaning and lubrication.

May 02, 2017 | Cars & Trucks

1 Answer

2006 2.5lt petrol X trail. Car is hard to start, can take up to 15 goes before it starts.have replaced both crank angle sensors


2003 nissan petrol xtrail stars some times other times just winds over
have changed crank and cam sensors reset ecu fitted new fuel pump still the same

Apr 26, 2012 | 2006 Nissan X-Trail 2.5

1 Answer

Have a 91 dokota 5.2 has no spark i changed the coil and the pickup in the dist do you know where the crank sensor is located


The crank sensor is on the front of the engine it triggers off the front crank pulley. The pickup you changed is the Camshaft position sensor and will cause hard starting but not a complete no start. A picture of the Crankshaft position sensor is below.


emissionwiz_180.jpg

May 17, 2011 | 1991 Dodge Dakota

1 Answer

I have a 1999 buick century with a 3.1 engine stop running while driving,ran codes came back with crank sensor,multiply cylinder misfire changed crank sensor,cleared codes,will start,but idles very rough...


Did you replace the crank sensor that is in the engine block between the engine and transmission? it has two and the one by the pulley hardly ever goes bad.

Dec 12, 2010 | 1999 Buick Century

1 Answer

2001 9/3 saab hard to start turns over cranks for


Change engine coolant temperature sensor/ECT/,located on a back side of the cylinder head. There is two sensors.ECT sensor is on a cylinder head,another is on water metal pipe.

Apr 12, 2010 | 2001 Saab 9-3

1 Answer

Throwed a code po335 crank sensor , i changed the crank sensor cleared the codes and 30 miles later check engine light came back on


Are you sure it was the crank sensor that you replaced? The cam and crank sensors look identical. Was the engine hard or slow to start? If so, this will sometimes set this code.

Nov 09, 2009 | 2006 Nissan Altima

1 Answer

1992 Buick Park Avenue - car runs great..when it runs.


The crank sensor is located on the side of crankshaft damper/pulley it mounted on a bracket. However it think that you may have a map-sensor problem that's very common with this vehicle. The crank sensor is not hard to change at all. Good Luck get back in contact if you need more help

Dec 18, 2008 | 1992 Buick Park Avenue

1 Answer

Can a cam sensor cause a hard start


Yes, cam sensor can cause a hard starting condition, but not that common on a 2000 maxima. I haven't replaced single one on a 2000 Max and I have one also (maxima that is) . Never had any problem with cam or crank sensors. I think that your problem is somewhere else, like IAC valve circuit. Just a tip. Its kinda hard to diagnose something over the computer, without Consult2 (Nissan scanner) beeing hooked up to the car and seeing what the car is doing while cranking for my self.

Oct 03, 2008 | 2000 Nissan Maxima

Not finding what you are looking for?
2005 Dodge Neon Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...