Question about 1994 Toyota Tercel

1 Answer

Clutch pedal sinks to floor

My clutch pedal sinks to floor .when I push the clutch pedal I only have a second to engadge the gear or I have to release the pedal and push it again. I have replaced the slave cylinder and no change. Please help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 42,687 Answers

Unless you have bled the slave cylinder properly there will still be air in it. However I think the problem is in the clutch master cylinder ---piston rubbers leaking fluid back to reservoir. Replace the m/cyl with new item and bleed out correctly.

Posted on Apr 28, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 14585 Answers

SOURCE: My 1993 toyota pickup won't go into gear.

there is still air in the system, keep pumping it will eventually come out. if it has a bleeder try that

Posted on Jun 15, 2010

  • 496 Answers

SOURCE: clutch pedal stays on floor when released

check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.

Posted on Feb 22, 2009

  • 1 Answer

SOURCE: 1985 TOY 4X4 PICK UP HARD TO GET INTO FIRST GEAR

May be a syncro ring going out. A tranney shop can rebuild the trans and change out the syncros or if you are good with mechanics you can get a book for your tranny and do it yourself. Most manual tranneys are not too hard to do.

Posted on Mar 23, 2009

  • 43 Answers

SOURCE: 1994 truck will not go into gear

is it grinding when you try to put in gear or is it just not going at all.detents or syncros

Posted on Mar 27, 2009

  • 7 Answers

SOURCE: replace slave cylinder on 89 toy.corolla sr5

If it was selecting gears ok before the clutch was replaced then the slave cylinder should be ok, it may just need bleeding. If it was playing up before, you can get them rebuilt by a brake specialist or a wrecker would be a cheaper option. They are very easy to replace, hardest part is bleeding them which is what I suspect is wrong with yours.

Posted on Apr 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just put a new slave cylinder and clutch master cylinder on a 2003 Honda accord 3.0 V6 six speed and you can shift the gears without the clutch pedal pushed in or the car started


that is normal if the gear synchro dogs ( teeth) are in line in the box
problems concerning a clutch are
slashing gears when trying to engage first or reverse with the pedal to the floor ---needs bleeding
slipping when the clutch pedal is released--- slipping clutch from the pressure not being released ---problem in master cylinder
reverse gear is the only gear not synchronised so even with the clutch depressed it is possible sometimes that it will not go into gear unless you let the clutch up to move the gears in the box then attempt to re-engage reverse

May 04, 2016 | Honda Cars & Trucks

1 Answer

Clutch pedal travel


Your pedal height may be adjustable by a stopper bolt at top of pedal. You would have to check the specification for your car. Most important that the pedal has about a half inch free travel before clutch begins to engage. You need that free play to ensure the release bearing (the throw-out bearing) is not touching the fingers on the pressure plate when not engaged. If it always is touching, it will be rolling around constantly and will go out prematurely.
Your new clutch will allow gear engagement sooner as the clutch pedal is released. I mean gears will engage just as pedal is lifting off from floor. You should notice that difference-the old clutch would have taken longer pedal travel from floor before releasing.

Apr 15, 2013 | Cars & Trucks

1 Answer

Int 806 will not move clutch is new


Fit 4th gear Release hand brakes on strait floor with open hood and push the car back and Forward to see if the engine engage your gear box if is not your clutch is back to front.if engage press the clutch pedal to make release of the gear,notes mechanical clutch cable or hydraulic system. check Release bearing arm position.

Sep 29, 2012 | Peugeot 806 Cars & Trucks

1 Answer

Put a cluth in a 1991 toyota mr2 turbo 2.0 and its still grinding when I shift gears.. what can I do to solvve my problem


have you replaced your fly wheel and release bearing when you changed your clutch disc?

if yes, then replace your transmission fluid.
also, if you know hot to adjust your clutch release, adjust it. adjust it in a way that you need to draw back your clutch pedal a little higher for the clutch to complete engage.

here are some ways to adjust your clutch.

1. for clutch using clutch cable. open your hood, locate for the transmision, and there you can see a cable that connects the transmision and the clutch pedal. loosen in up a little.
2. for hydrovac clutch with self correcting features. just pull your clutch pedal away from the floor for a few seconds and its done.
3. for hyrovac without self correction. manually adjust the push rod (metal rod that connects the clutch pedal to the clutch master)

Aug 08, 2011 | Toyota MR2 Cars & Trucks

1 Answer

I am unable to put my 2001 Ford Escape xls into gear! When I push the clutch pedal down all the way to the Floor and try to enter a gear it will not go at all. I had issues with it in the morning it did...


that is your clutch pump/cable in not functioning. u need to check the fluid level (if your car using hydraulic clutch) or your clutch cable broke...

Nov 19, 2010 | 2001 Ford Escape

1 Answer

1998 Saturn SC1 manuel stick is hard to shift into 1st & 2nd gear


Try to double clutch the clutch pedal. How to double clutch; push the clutch in moving the stick to neutral, then release the clutch and then push it back in and shift into first or second gear. If it works then it is not the shift linkage and could be a clutch adjustment. First how far do you have to release the clutch pedal until the clutch plate starts to engage? If only an inch or so the clutch pedal needs to be adjusted, which is an easy fix (this is more common). The other possible problems could be the clutch plate, throwout bearing of syncros could be bad. If it is one of the previous problems double clutching should buy you some time.

Jul 01, 2010 | 1998 Saturn SC

1 Answer

Car stalls when braking


It appears that the clutch is not releasing properly when you push the pedal down. How much free-play does the pedal have when you start to push it down? It should be about 3/4 inch or so. With the engine off and in first gear, have someone push the clutch pedal down all the way while you try to rock the car back and forth. If it is trying to turn the engine while you do this, the clutch is either not capable of being released or the clutch hydraulic system is delivering insufficient oil to the slave cylinder at the clutch release arm/shaft. If this worked correctly before the new parts were put in, the person(s) that did the work should be responsible for getting it to work again. Make sure that you don't have several floor mats that are under the pedal thus preventing full clutch release. Hope this helps!

Apr 04, 2010 | 1989 Volkswagen agon

1 Answer

1997 hyandai accent gt clutch problem


hi considering age of car and that you have no leaks on hydraulics? may i suggest you try bleeding the clutch to rid of old fluid a couple of pumps may be suffice ? b/fluid does absorb moisture and heat over time hence recommendation tat fluid be changed at period specified in handbooks ie 12 monthly ?

May 15, 2009 | 1994 Hyundai Excel

Not finding what you are looking for?
1994 Toyota Tercel Logo

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...