Question about Cars & Trucks

1 Answer

How to tighten serpentine belt on 2003 mercedes e320

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,026 Answers

Most serpentine belts are adjusted on the idler pulley. Undo the nut holding the pulley on just enough to allow the pulley to slide up or down At the rear if the pulley bracket look for an adjuster screw parallel to the pulley screw this up or down to adjust the tension. When done retighten the pulley nut.

Posted on Apr 28, 2013

  • Derrick Apr 28, 2013

    U the man

  • Derrick Apr 28, 2013

    Where can I find a video on how to tighten belt

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bschilz
  • 2049 Answers

SOURCE: I need the diagram for serpentine belt routing on

Here's the diagram you asked for...

85cf64b.jpg

Posted on Jan 25, 2010

SOURCE: 2003 Mercedes benz e320 brakes

It is imperative that you loosen the caliper bleed screw BEFORE you push the piston back into the caliper. Failure to do so WILL damage the ABS hydraulics.

Posted on Apr 17, 2009

greg_margo
  • 1959 Answers

SOURCE: need a diagram for serpentine belt replacement for mercedes benz

Below is a link for your diagram. Best of luck!
Greg

http://www.mvreader.com/multiview/dayco/zoom.php?zoom_item=C0002R&l=n&catalog=auto&category=2

Posted on Jun 18, 2009

  • 165 Answers

SOURCE: my 2003 mercedes e230 wont start

battery--petrol filter-- petrol pump, hoses,clips.

Posted on Apr 17, 2010

michael4wgv
  • 166 Answers

SOURCE: how to change a serpentine belt clk320 2003

just put a socket and rachet on the bolt for the tensioner pulley and move the tensioner to the right to loosen the slack on the belt.

Posted on Oct 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

E320 cdi serpentine belt diagram


any parts store will have a catalog for belts and hose applications.In the catalog there are diagrams for belt routing have them make you a copy eaasy fix

Jun 05, 2012 | Mercedes-Benz Cars & Trucks

1 Answer

MERCEDES BENZ 2003 MODLE E320,HOW TO BLEED BRAKES


remove brake fluid filler cap start at the wheel closest to cervo then move away so front to back remove road wheel there is a brake nipple on the caliper put a piece of tubing around nipple and into a jar with clean brake fluid in it loosen nipple get some one to pump brake peddle about 10 times on the final stroke keep peddle pushed to floor then tighten nipple up pump brake peddle a few time should be hard then repeat all wheels rear should only have 1 nipple for rear wheels but check this any way

Jul 02, 2011 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

Route needed to replace serpentine belt on mercedes c180 kompressor 2003


The serpentine belt routing diagram on Mercedes C180 Kompressor 2003

tdisline_478.jpg
CS = Crankshaft
G = Guide pulley
Gen = Alternator
SC = Supercharger (Kompressor)

T = Tensioner
AC = Air Conditioning
PAS = Power Assisted Steering

Apr 27, 2011 | Mercedes-Benz CL550 Cars & Trucks

1 Answer

How to replace an engine belt on an 1995


I have two Mercedes - one is 2000 E320 Wagon; other is 1999 E320 Sedan.

I replaced the serpentine belt on my 2000 Wagon today at 92,000 miles. I found that the Motorcraft JK6-947 could be purchased on Ebay for $12.99 plus $6.20 shipping. The old belt was a Goodyear Gatorback 4060940. My 1999 sedan has a Mercedes Benz 011 997 97 92 6K2390 EM7117 Gates belt made in Spain.

Here are the details of replacing the belt.

On the 2000 E320, a 17 mm bolt just under the belt going to the tension pulley will release the belt tension when turned counterclockwise. Removal of the belt was easy after using a 17 mm deep socket wrench similar to a spark plug socket. I made turning the bolt very easy by slipping a 4' pipe over the socket wrench handle. It is advisable to put the new belt LAST on the idler pulley that contacts the belt only on the smooth side.

You do not need todisturb theButton Torx bolt in the center of the tension pully.

The 1999 E320 uses a 15 mm bolt in the CENTER of the tension pulley. Otherwise the installation is the same as the 2000 E320.

Jan 19, 2011 | 1995 Mercedes-Benz E-Class

1 Answer

Need diagram for serpentine belt for a 96 e320?


Should have a sticker under the dash for the belt. Also try your owners manual. If its not there try peachparts.com or benzworld.com for it.

Apr 08, 2010 | Mercedes-Benz E320 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...