Question about 2001 Toyota Camry Solara

1 Answer

Bumper Removal how do i get the bumper off my 01 solara to replace my headlight assembly

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 42 Answers

This video should help you. The bumper should not have to be removed.
http://www.youtube.com/watch?v=8ap1-CzG5Hc

Posted on Apr 27, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: Trouble removing 1999 Solara Grille

sorry to tell you that but you must take the bumper off and its pretty easy there are retainers up top remove them remove the bottom of the bumper ones and they may have bolts now for the last part its 100 mm at the fender edge and bumper just slide off and then you can take and change the grille

Posted on Jan 27, 2009

  • 840 Answers

SOURCE: 2004 toyota rav4 rear bumper assembly guide

there are two bolts to the center and two around the corner on at the edge up high and one at the bottom of the bumper/ Please rate my response thank you very much

Posted on Feb 01, 2009

  • 1 Answer

SOURCE: front grill on toyota solara

That is correct - it worked for me - now the questions is - How do I remove the old logo ?

Posted on Apr 25, 2009

  • 4 Answers

SOURCE: 01 solara fog lamp replacement

nono... go in through the engine. Pop the hood and you can do it without detaching anything but the old fog lamp.

Posted on Jun 08, 2009

ZJLimited
  • 17970 Answers

SOURCE: I need to remove the front bumper cover on a 2002

Open hood and look on top of headlamps. You see a piece that looks like it slides in behind the light.

Have removed two mounting srews. Disconnected plastic grill. The bottom of the head light is held in by snap clips. The bumper cover needs pulled out far enough in order for the assembly to clear and come out.

Posted on Mar 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need to change out the headlight assembly


Here's a guide on head light removal.

Feb 06, 2013 | Cars & Trucks

1 Answer

How to take passenger headlamp out of 328i bmw 2008 so it can be replaced?


2008 328i Passenger headlight assembly removal.

The headlight assembly is held in by 4 "star" bolts (size 25); 2 visible on the top of the assembly, 2 not visible or easily accessible.

The 2 bolts not so visible require that the front half of the wheel well come off and the front bumper or "nose" of the car.... The bumper is what needs to come off, but there are 2 bumper bolts hidden by the wheel well.

The wheel well is held in by 7mm bolts, 2 of which are actually bolted to the bumper on the bottom.

The front bumper is held on with 7mm bolts on the bottom edge, and star bolts, size 25, accessible on the top edge. (Hood open). Here were my steps.

1. Jack up the car on the side you are replacing, remove wheel.
2. Using 7mm socket, remove all the bolts to peel off the front half of the wheel well. With the wheel well out, you can see the 2 other star bolts holding the headlight assembly, but you can only remove one of them... even if you were good enough to get both removed, the headlight assemble will not push out through the bumper.... Keep going with bumper removal.
3. Remove 2, 7mm bolts of the front bumper that are now visible up near the outer edge of the headlight assembly.
4. At this point I removed the bumper's top edge start bolts and bottom edge 7mm bolts about 3/4 of the way across the bumper...
5. The bumper is very flexible and you can now pull it back , reach in, and get that last difficult star bolt on the headlight assembly....
6. Don't forget the one electrical connector....
7. I also recommend testing the new assembly by plugging it in before removing anything

Nov 09, 2012 | Cars & Trucks

2 Answers

How do i change my headlight assembly on a 2001 honda accord


HEADLIGHT REPLACEMENT

1. Remove the front bumper
2. Disconnect the connectors (A).
3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).

Fig. 21: Removing Mounting Bolts & Headlight Assembly
6_26_2012_3_27_45_pm.jpg

Jun 24, 2012 | 2001 Honda Accord

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

Do I have to remove the tray liner from the 2003 Rodeo pick up to replace tail light assembly?


Utility And Sportside Pick-Up Models
  1. Make sure the headlight switch is off and the ignition switch is in the lock position.

  2. Unfasten the screws retaining the lens, then remove the lens.

  3. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

  4. Remove the bulb from the socket.

  5. Installation is the reverse of removal.
    Without A Step Bumper

    1. Make sure the headlight switch is off and the ignition switch is in the lock position.

    2. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

    3. Pull the bulb from the socket.

    4. If necessary, remove the lens retaining clip and the lens from the filler panel.

    5. Installation is the reverse of removal.
      With A Step Bumper

      1. Make sure the headlight switch is off and the ignition switch is in the lock position.

      2. If necessary, lift the lamp up and tilt the bottom away from the bumper to release the lamp retainer.

      3. Disconnect the bulb socket from the license plate lamp by rotating it 1/4 of a turn counterclockwise.

      4. Pull the bulb from the socket.

      5. If necessary, remove the step bumper pad, the screws that attach the lamp to the bumper and remove the lamp assembly.

      6. Installation is the reverse of removal. Tighten the lamp assembly-to-bumper screws to 14 inch lbs. (1.6 Nm).

Dec 12, 2010 | Isuzu Pickup Cars & Trucks

1 Answer

How to remove headlamp assambly in a volvo s60 2002


Hello,

This should be fairly simple,one may have to remove the grille.

  • Remove trimmings on the front bumper cover to allow access to the bolt for removal of the front bumper. The trimming can be removed simply by prying the trimming from the center of the bumper cover using a Philips screw driver.
  • After removing the 2 bolts on the bumper cover, you may open the hood and remove the plastic fasteners on the top of the bumper.
  • To remove the plastic fastener, simply depress the center until click. Do not press too far or the fastener will be damaged.
  • Turn the Torx screw in the wheel well counter clockwise to loosen the catch plate on the bumper. Lift the bumper cover over the catch plate and push the bumper cover forward. This completes the removal of the front bumper cover.
  • To remove the headlight assembly, you will need to loosen the bolt on the retainer near the wheel well. You will then remove the 4 bolts that hold the headlight assembly.
  • There is one bolt on the side of the headlight assembly. Two bolts on top and one at the corner of the lens. They all have the same size bolt.
  • In order to remove the headlight assembly, after removing the bolts, the headlight harness needs to be removed.
  • The next step is to remove the trimming on the lens and removing the clips that hold the lens in place. There are 4 clips. One clips on each side.
  • Once the clips are removed, the lens can be pry open with screw driver. You may want to heat the edge to soften the glue or use an utility knife to scrape the edge. Be extra careful, as the glass can be very sharp if shattered. Please also wear protective gear such as safety goggle and gloves. After this, just reverse the steps to put the headlight back together.
Take care and good luck

Nov 06, 2010 | 2002 Volvo S60

1 Answer

How to change the headlight asembly on 2004 acura rl does the front bumber have to come off


yes the front bumper needs to come off see instructions below
  1. Remove the front bumper and front bumper upper beam.
  2. Disconnect the connectors.
  3. Remove the four mounting bolts, then remove the headlight assembly.
  4. Install the headlight in the reverse order of removal.
  5. After replacement, adjust the headlights to local requirements

Oct 18, 2010 | 2004 Acura 3.5RL

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

2 Answers

Bumper cover removal


Its easy look at the bottom of the bumper has retainers and the fenders have a bolt on each side then just slide off

Jan 23, 2009 | 1991 Honda Accord

2 Answers

Need to replace headlight assembly on 2005 Ford Escape


ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

n0037234.gif
Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
Removal and Installation
NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 3 headlamp assembly bolts.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the headlamp assembly nut and the headlamp assembly.
    • Disconnect the electrical connectors.
    • To install, tighten to 5 Nm (44 lb-in).
  1. To install, reverse the removal procedure.

Jan 01, 2009 | 2005 Ford Escape

Not finding what you are looking for?
2001 Toyota Camry Solara Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...