Im trying to remove my fronts seats in my opel vectra touring. there 4 star screws that are turning with excessive force which look to be holding the seats into the base chassis of the car but not loosening or letting the chairs come looses i was hoping that ya could maybe send me a step by step guide on how to remove and fit the driver and passenger seats i just want to get them renewed but this seems to be a big problem. cheers
Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!
Posted on Jan 02, 2017
SOURCE: Star bit on front brake 2000 chevy 1500 ?
YES THEY COME IN METRIC SIZES. AND,MOST GM PRODUCTS ARE ALL METRIC THESE DAYS. GET A MERTIC SET. YOU WILL ALWAYS USE THEM AGAIN. TOOLS ARE A GOOD INVESTMENT.
Posted on Jan 24, 2009
SOURCE: 1991 Nissan Maxima: Removal of front driver side door panel
This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal
Posted on Mar 20, 2009
SOURCE: Need wide comfortable driver seat/front passenger seated suv/van
contact the ford motor company.... they are the leaders in van conversions .... often converting ford windstars... can't remember what the new van is but it's exactly the same as a windstar... just a different name. i have found you the page to go to for and they will help you work out what you need.
http://www.fordmobilitymotoring.com/
Robert
Posted on Mar 21, 2009
SOURCE: stuck front passenger seat - wont slide back or forwards due to small screw lodged in floor runner
Be there done that, but with a penny. All you can do is either get real aggressive with a hammer and long metal object as a punch or pull the seat. The seat should have 4 bolts. One at each end of each track. Ising a 1/4 in drive rachet and either a 1/2 or 9/16 socket should work. 1/4 in drive is low profile.. good luck
Posted on Jun 02, 2009
SOURCE: FRONT HEATED SEATS
you need to check the resistance in each of the heated seat elements in the seat. There's a two wire connector under the back of each front seat. The connector should be green. disconnect it and measure the resistance along the circuit going into the seat. if it isnt .1 - .3 ohms, replace the appropriate heated seat element
Posted on Jan 06, 2010
Nov 02, 2017 | Volvo Cars & Trucks
on Feb 04, 2015 | Opel Vectra Cars & Trucks
Jun 10, 2015 | 2000 Oldsmobile Intrigue
Jun 21, 2014 | Opel Vectra Cars & Trucks
Apr 25, 2014 | 1997 Plymouth Voyager
Apr 30, 2013 | Cars & Trucks
Mar 04, 2013 | Cars & Trucks
Apr 02, 2011 | Honda Accord Cars & Trucks
Oct 12, 2010 | Oldsmobile Cars & Trucks
Mar 21, 2010 | BMW 525 Cars & Trucks
44 people viewed this question
Usually answered in minutes!
×