Question about 1991 Toyota Pickup

1 Answer

Driveshaft noises we just replaced the clutch and now when the truck is driving there is a clinking noise only when it is in gear and moving.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Toyota Master
  • 5,817 Answers

CV joint is worn out,you have to replace.

Posted on Apr 27, 2013


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 155 Answers

SOURCE: loud clanking noise in gear if the clutch is not engaged

Almost sounds like a throwout bearing problem. Either way, bring the car back and make them fix it. It will be covered under the warranty so dont let them try to convince you otherwise.

Posted on May 28, 2009

  • 1486 Answers


Clutch plate springs brocken.Thats where your noise is comming from.The only solution is to change the clutch.Hope that was helpfull.

Posted on Jul 24, 2009

  • 141 Answers

SOURCE: screeching noise from wheel area when driving slow

could be the brake hose collapsing from the inside....lets fluid go in to piston,but wont let it back out,so caliper sticks and drags on rotor....

Posted on Sep 16, 2009

  • 1 Answer

SOURCE: I have a 92 2 wheel drive Toyota pick up 5 speed

4th gear is a staight through gear thats why it doesnt make noise. sounds like you are about to lose all gears except 4th. this is common on toyotas when the rear seal on the tranny goes out which causes the tranny to basically pump out the tranny fluid. without fluid or a low level the gears slowly grind away all exept 4th. a rebuilt 5sp is not that expensive on ebay.check the fluid, if it is real low its too late, replace the tranny.

Posted on May 12, 2010

  • 207 Answers

SOURCE: 03 Toyota mr2, clutch noise.

I hope its your release bearing, but I had this same issue with my Audi and it turned out to be I need a new transmission, the gears are not catching it sounds like. your synchros may also be off. Does it do this in every gear, and once it does move, does the clutch slip?

Posted on Mar 24, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Mini cooper 16 02 no drive or noise cluch pedal normal

When you put in gear /handbrake off can you push it to move it [if no ] push in clutch ,will it move now ,if yes then clutch is ok if no then either clutch OR main drive gear locking nut in gear box has a problem.

Feb 11, 2015 | Mini Cars & Trucks

1 Answer

03 Toyota mr2, clutch noise. clutch replaced a year prior. 2 weeks before i heard some noise when shifting. 1 week before it was hard to shift a few times. then one night after driving home i parked and...

I hope its your release bearing, but I had this same issue with my Audi and it turned out to be I need a new transmission, the gears are not catching it sounds like. your synchros may also be off. Does it do this in every gear, and once it does move, does the clutch slip?

Mar 24, 2011 | 2002 Toyota MR2 Spyder

1 Answer

Driving alongfreeway abiut 100 klms hour all going fine 1 moment then out of the blue there was nothing, no gears, just reving like in netural. no noise was heard either

If this is an Automatic it would be the Torque converter. If you have someone to look under the car when you put it in gear, see if the drivehaft is turning. If the driveshaft is turning and the differential is not, you blew the rearend. If the driveshaft is not turning it is the Torque converter.

If this is a stickshift it would be unusual to detroy the clutch without some noise.

Mar 27, 2010 | 1966 Ford Mustang

3 Answers

Whining/grinding noise at deceleration

We have the same problem at our shop. We haven't rebuilt the front differential yet. We tried 3 different shafts on 2 different Jeeps and the noise is on both just the same. By greasing the front driveshaft cv joint, we got he noise to quiet some, but it is still way to loud. With the driveshaft out, the noise is gone. We are about to buy a new shaft from the dealer for $600. There are some service bulletins about some noisy driveshafts.

Jun 15, 2009 | 2009 Jeep Grand Cherokee

3 Answers

Rear end

clunking or grinding noises, wont accelerate to full potential,

May 07, 2009 | 2001 Ford Ranger Regular Cab

1 Answer

2001 Jeep Wrangler 5spd.... 2wd is out!

Either you have broken something inside the transfer case but equally likely is that you blew up the spider gears in the rear differential. I'd remove the cover and take a look. If they're broken, it won't be difficult to see.(smaller gears inside the center section) And, they are replacable
Hope that's all it is!
Good Luck!!!

Apr 01, 2009 | 1991 Jeep Wrangler

1 Answer

When pressing the gas pedal the engin will make this metal clink


Feb 06, 2009 | 2000 Nissan Maxima

Not finding what you are looking for?
1991 Toyota Pickup Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides