Question about 1998 Chevrolet Camaro

1 Answer

Find guide to replace driveshaft - 1998 Chevrolet Camaro

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,649 Answers

You need deep socket 32 or 34 mm.remove tie rod 18 mm and strut 21 mm.Then pull out.

Posted on Apr 28, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a front axle on a 2002 freelander landrover


1. Remove hub centre disc and remove hub nut with wheel on ground.

2. Jack up affected side (not under lower control arm), remove wheel.

3. Remove two caliper bracket bolts and tie caliper up out of the way.

4. Disconnect outer steering joint.

5. Remove two strut-to-hub bolts and pivot hub outwards to release driveshaft outer drive flange.

6. Place oil catch can under car and carefully pry out inner driveshaft joint and remove driveshaft.

7. Reverse steps with new driveshaft. Remember to replace any lost gearbox / transfer box oil.

Apr 23, 2015 | 2002 Land Rover Freelander

1 Answer

1993 gmc Sierra driveshaft


Be careful with recovered units. make bloody sure that it has no kinks and not bent - look down the shaft and turn it. If the last one fell out, sounds like the previous joker used one that was too short different models of the same marque can have different lengths.

Jul 22, 2014 | 1993 GMC Sierra

1 Answer

How to replace nearside driveshaft on renault trafic 2010


sorry I can not help you I take mine to the garage

Jun 13, 2014 | 2009 Renault Trafic 1.9dCi

1 Answer

Have vibration ujoint broke at transfercase had to replace driveshaft with used one have vibration now whats my next step


Find a shop to balance driveshafts and replace the U-Joints. You either have a bent driveshaft or a balance problem or bad U-joints.

If you have the time, the only other thing you can do is mark the driveshaft and remove the driveshaft and clock the flanges. But remember that each flange is 180 degrees difference because most U-joints have a big and small bearing cap. So to get an effective 90 degree change just make the change on 1 flange and reassembly and try it.

This is why a company which balances driveshafts is a good idea.

Please rate my info.

Jan 18, 2013 | 1989 Dodge Ramcharger

1 Answer

Is a 2004 ford f-150 2wd carrier bearing.. ( mid-mount bearing ) on driveshaft replaceable, or do i have to replace entire driveshaft?


it is replaceable
normally it comes complete in the rubber mount
you will have to undo the drive shaft flange at the bearing
remove the drive shaft and take it to an accredited drive shaft repair shop or take the vehicle to an accredited drive line specialist shop
the repair will require that you place the flange back on the shaft after the bearing replacement in exactly the right position or you will get harmonic vibration after the job so talk with the experts first if you want to diy

May 09, 2017 | Gateway Cars & Trucks

1 Answer

How do i replace a driveshaft for a 1997 lincon cotanental


I searched under 1997 lincoln continental and found this: Driveshaft and U-Joints
REMOVAL & INSTALLATION Town Car and Mark VII-VIII Fig. 1: The bolts retaining the rear driveshaft yoke-to-differential flange require a 12mm, 12 point wrench or socket to loosen them 91197p12.jpg
Fig. 2: Remove the bolts retaining the rear driveshaft yoke-to-differential flange 91197p11.jpg
Fig. 3: Separate the driveshaft from the axle flange and . . . 91197p13.jpg
Fig. 4: . . . disengage the driveshaft from the transmission output shaft 91197p14.jpg
Fig. 5: Insert a plug onto the splines of the transmission output shaft to prevent fluid from leaking out 91197p15.jpg
  1. Raise and safely support the vehicle.
  2. Mark the position of the driveshaft yoke on the axle companion flange so they can be reassembled in the same way to maintain balance.
  3. Remove the flange bolts and disconnect the driveshaft from the axle companion flange.
  4. Allow the rear of the driveshaft to drop down slightly.
  5. Pull the driveshaft and slip yoke rearward until the yoke just clears the transmission extension housing seal. Mark the position of the slip yoke in relation to the transmission output shaft, then remove the driveshaft.
  6. Plug the transmission to prevent fluid leakage. To install:
  7. Lubricate the yoke splines with suitable grease.
  8. Remove the plug from the transmission and inspect the extension housing seal; replace if necessary.
  9. Align the slip yoke and output shaft with the marks made at removal and install the yoke into the transmission extension housing. Be careful not to bottom the slip yoke hard against the transmission seal.
  10. Rotate the axle flange, as necessary, to align the marks made during removal.
  11. Install the driveshaft yoke to the axle flange. Install the bolts and tighten to 71–95 ft. lbs. (95–130 Nm).
  12. Lower the vehicle.
prev.gif next.gif

Jul 05, 2010 | 1997 Lincoln Continental

2 Answers

2005 ford escape 3.0L AWD XLT - DRIVESHAFT CARRIER BEARING BAD - CAN IT BE REPLACED OR MUST I CHANGE THE DRIVESHAFT FRONT AND REAR?


if there is some one in your area that balances driveshafts they can change just the bearing for you

Nov 10, 2009 | 2004 Ford Escape

1 Answer

How do you remove axles on a 2000 hyundai accent?


Very carefully. 1. Loosen the wheel nuts slightly. 2. Raise the front of the vehicle, and support it with safety stands in a proper location. 3. Remove the wheel nuts and front wheel. 02590df.jpg 4. Remove the split pin, the castle nut and the washer from the front hub. 5. Drain the transmission fluid before the driveshaft is removed. 6. Using a plastic hammer, make the driveshaft disconnected from the axle hub.
1817034.jpg 7. Push the axle hub outward and separate the driveshaft from the axle hub. 8. Insert a pry bar between the transaxle case and the tripod joint case, and pry the driveshaft from the transaxle case.
4d4e228.jpg caution_icon_eng.gif Be sure to apply the pry bar to the rib of the transaxle case. Do not insert the pry bar too deeply, as this may cause damage to the oil seal. [max. depth : 7 mm (0.28 in.)] For automatic transaxle equipped vehicles, insert a pry bar into the groove of the driveshaft to remove the driveshaft from the transaxle. Do not pull on the driveshaft; the joints may come apart. Be sure to use the pry bar. 9. Pull out the driveshaft from the transaxle case. caution_icon_eng.gif Place a plug in the hole of the transaxle case to prevent contamination Support the driveshaft properly. Replace the circlip each time the driveshaft is removed from the transaxle case.

Jun 12, 2009 | 2000 Hyundai Accent

1 Answer

Touareg 04 rear driveshaft replacement


By the labour book I use it says 2.9 hours to remove the driveshaft plus another .5 to change the bearing.

May 25, 2009 | 2004 Volkswagen Touareg

3 Answers

Driveshaft yoke balancer


Remove it. Then drive the truck to see if it vibrates. If it don't forget it. If it does, replace the driveshaft. But get it off there before it breaks something.

Mar 16, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
1998 Chevrolet Camaro Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...