Question about Cars & Trucks

1 Answer

I installed a new clutch kit in my truck.I didn't

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 50 Answers

Try bleeding the air out of slave cylinder

Posted on Apr 27, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2920 Answers

SOURCE: how to remove clutch slave cylinder on a 95 sunfire

no you dont have to pull the tranny to get to the slave cylinder.it should be located on the drivers side almost under the door or right in front of the door, at least thats where mine was at

Posted on Jan 03, 2009

  • 2 Answers

SOURCE: PEUGEOT 406 LX DT 1998 2088 CC CLUTCH SLAVE CYLINDER

I understand these cars have a sealed clutch system. When they fail you replace the whole kit master,hydrolic pipe and slave (comes in one piece). Search on ebay maybe £45 or so.

Posted on Feb 26, 2009

Keith100881
  • 74 Answers

SOURCE: put in new clutch and slave cylinder. no clutch pedal. how do you bleed the cylinder?

work it back and forth with your hand and you will get pedal after a while then bleed like you would brakes get help so one can pump and the other can bleed

Posted on May 24, 2009

  • 145 Answers

SOURCE: after replacing starter and removing slave cylinder, clutch fails to work

sounds like you have a air pocket or you fail to engage the slave cylinder push rod If you disconnected the slave cylinder from the hose proceed to bleed out the slave cylinder if you didn't take you slave cylinder and whit out disconnecting the hose and make sure the push rod is against the clutch push arm.

Posted on Jun 13, 2009

wilsodfarm
  • 986 Answers

SOURCE: hydraulic clutch 1995 chevy 1500 truck

I know you dont want to hear this but it sounds like the clutch plate is in backwards.

Posted on Oct 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just finished putting on a new gear box and clutch kit for and when i started it and put it on gear it was so low and soft and a loud noise after that... I just want to know why did it do that pls?


So you installed a new transmission and a whole new clutch kit? Did the kit include the pressure plate, clutch, throw out bearing and slave cylinder? Did you bleed the slave cylinder? The low and soft pedal is a clear sign that there is air in the hydraulic system. The loud noise after that tells me you're either grinding the gear trying to shift or there is a problem inside the transmission itself. If you installed everything correctly and torqued all the bolts correctly in the clutch assembly and transmission, then try bleeding the slave cylinder again, sometimes air gets trapped in the cylinder and it's hard to get out, If you let the clutch master cylinder run dry while you either had the clutch apart or while you were bleeding the clutch, then you have to start from scratch and re-bleed the whole system.

Sep 19, 2016 | Cars & Trucks

1 Answer

What's wrong with my clutch if my 1998 escort won't go into gear. There is small resistance in my clutch pedal


Jamie, are you losing any fluid from the clutch master cylinder? By small resistance I presume you mean the pedal feels soft?

If you're losing fluid from the master cylinder you have an obvious leak somewhere and air is getting into the system.

Most leaks occur from the clutch SLAVE cylinder as it does all the work .. If there's no leak from the clutch slave cylinder, suspect the seals inside. It's like a bicycle pump ..the seal inside wears and it won't pump..

You may be able to get an overhaul kit. I'm in the UK .. but here's an Ebay link for a slave cylinder overhaul kit just to show you what it looks like:
FORD CORTINA MK2 CLUTCH SLAVE CYLINDER REPAIR KIT SP2085
Here's a link to show you what the slave cylinder itself may look like (it may NOT be for your vehicle..)
CLUTCH SLAVE CYLINDER FORD FIESTA ESCORT
It's easier and quicker to fit a new slave cylinder than it is to strip down and replace seals with a kit. Be aware, after overhauling or replacing a slave cylinder you have to bleed it - remove the air.

The easiest way of doing this is to make sure the reservoir is fill of fluid, crawl underneath the car with a spanner/wrench, place a rag over the bleed point and get somebody to pump the pedal a couple of times while you undo then tighten the bleed nut.

If it's not the slave cylinder at fault- then it's the master cylinder. Master cylinders also have a 'piston' and rubber seals which wear/perish.
However, it's more than likely that it's the slave cylinder at fault

Mar 21, 2016 | Cars & Trucks

2 Answers

Can't find a clutch slave cylinder for my 1992 acura vigor GS 2.5, 5 cylinder. I need to rebuild the one I have! How can I rebuild the clutch slave cylinder?


Get it online
Doesn't cost much
Lots of places have it
You not going to rebuild a part like that
there too cheap new

Jul 22, 2013 | 1992 Acura Vigor

1 Answer

I had a new clutch asembly and new slave cly put in my 1990 nissan truck about year and half ago. My problem is my clutch is hard to push down and if i don't push it all the way to floor it will g


replace the clutch master cylinder. The rubbers on the piston swell over time and/ or break down blocking up the ports in the cylinder.. Wrong fluid is the main culprit for this type of fault.

Mar 29, 2013 | Cars & Trucks

1 Answer

Need to know how to change a clutch disc on 90 ford f150


Instructions
  1. Remove the Old Clutch
    • 1Remove the exterior parts (those that are not in the engine compartment) to include the floor shifter inside the cab of your F-150 and the exhaust pipe
    • 2Remove interior parts--those parts that are under the hood. This includes the starter, which is attached to the transmission bell-housing. Disconnect the drive-shaft of your F-150 and the hose for your truck's hydraulic slave cylinder.

    • 3Remove the transmission from your F-150. Using a metric socket set, undo the transmission cross-member and bolts, which will allow you to remove the transmission from the truck. You should have plenty of room to work underneath your F-150, as these are tall trucks. In some cases, especially if your truck is lowered, consider using a lift or a jack to raise your truck off the ground for easy access to all components.
    • 4Remove the pressure plate and the worn clutch disk from the transmission.
    • 5Inspect the flywheel. If the clutch flywheel shows significant amounts of wear or is damaged in any way, you should replace it. Reusing a damaged flywheel can cause your new clutch to fail.
    Install the New Clutch
    • 6Install your new clutch disk and pressure plate. You'll need to use the clutch alignment tool, which should come as part of your clutch kit. If your clutch kit doesn't include this tool, you can buy it at an auto partsicon1.png store or any Ford dealership.
    • 7Replace the transmission back into your F-150. Remember to reconnect the transmission cross-member and all bolts.
    • 8Reconnect all interior parts--including the starter, drive-shaft and the hose for the hydraulic slave cylinder. Don't forget to bleed the slave cylinder when you attach the hose.
    • 9Reconnect the exterior parts, which includes the exhaust pipe and the gearshift inside the cab.
    • 10Drive your F-150 slowly in a controlled environment. This will ensure that the new clutch is installed properly and is in good working condition

Oct 03, 2012 | Ford F-150 Cars & Trucks

2 Answers

I replaced the clutch in a 1996 pontiac grand am gt now the clutch petal goes allthe way to the floor and wont retract itself


Find out if this is a hydraulic clutch. Being a 2005, it most likely is and sounds like your slave cylinder went out. I'm not sure where this is on your car, however it is usually mounted on the driver side firewall below the brake mastercylinder (brake fluid resevoir).
If it is not located here (call an auto parts dealer for location, and a repair manual) then you may have an internal slave cylinder which is located in the transmission with the throwout bearing. You will need to pull the passenger side drive axle, seperate the transmission from the engine (if front wheel drive) to replace.
Inquire with your local auto parts dealer or dealership for further details and repair options, and if this is actually the issue. If it's internal, look for a puddle directly below the engine. If the slave cylinder went out, then you'll have a puddle under the engine.
Also, if the slave cylinder (if hydraulic) is mounted to the firewall, either it is bad and needs replaced; needs to be bled (like brakes) or you may not have put the throwout bearing on correctly and it came loose.
Again, inquire with the dealership or an auto parts dealer for details (or a certified mechanic for repairs).
Please let me know if you need further assistance.
carsandcomps

Aug 20, 2011 | 2005 Nissan Sentra

1 Answer

F250 1995 clutch slave cylinder


Welcome to Fixya

You didn't mention in your question what you want to do with the clutch slave cylinder. Anyway, if you want to replace it, please see procedure below:

Since it is a pressurized system, remember to bleed out the fluid before completing the job so that you remove any dangerous air pockets in the lines. Remove the connector to the clutch, the tube that runs hydraulic fluid from the master cylinder, and the two bolts connecting the cylinder to the bell housing. Take the new slave cylinder, fill it accordingly with fluid, re-attach it, run the fluid through the system, and test the resulting pressure.

Thank you for using Fixya!

Jul 06, 2011 | Ford F-250 Cars & Trucks

1 Answer

05 new shape passat.fitted new clutch kit with flywheel.on bleeding clutch pedal went hard approx 1 inch short of full travel,when pushed further it popped the seal on slave cylinder.refitted another slave...


the only way that the seal pops is when the piston comes out the end of the cylinder that indicates that the installation of the clutch kit is incorrect and the throw out arm is not in the throw out bearing carrier properly
regardless of makes , if the clutch kit is made for that vehicle it will fit

Jun 18, 2017 | 2006 Volkswagen Passat

1 Answer

Installed clutch kit and now wont go into gear


problem may be the thickness of your clutch disc and preasure plate faces

Sep 01, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

Clutch works fine until. except that it doesnt


I don't have that shop manual, but the slave cylinder looks like a small brake master cylinder and is on the firewall on the driver side.
Check to make sure floor pan is not split by slave cylinder. Some had weak floors that needed reinforcing. Ford had a kit.

Otherwise, replace slave cylinder. tascafordparts.com sells at discount.

Please rate as fixya if this solves your problem.
Report back and good luck

Mar 05, 2009 | 1989 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...