Question about Cars & Trucks

1 Answer

Dashboard Remove do I need to remove dash,to replace passenger airbag.if I need to,how to remove dashboard.kia venga.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 50 Answers

I wouldn't suggest doing it yourself

Posted on Apr 27, 2013


6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 9 Answers

SOURCE: dashboard removal of '98 dodge ram 2500

on the 98 model the fuse box can be removed without removing the whole dash board.

Posted on May 02, 2009

  • 3600 Answers

SOURCE: How do I remove the dashboard from my 2000 Chevy Astro Van?

Paul is right you can go to radio shack or autozone schucks or any parts store and ask for the removal tool it cost $20.00 tops. Trust me you don't want to undo the dash as the air bag could detonate if you shorted the two wires that can control it and it could kill you.

Posted on Sep 22, 2009

Testimonial: "Thank you! I didn't even think about the safety aspect of removing the dash. Better leave this to the pros!"

  • 416 Answers

SOURCE: how do I remove the dashboard from E250 Ford

I would check the blower motor resistor 1st

Posted on Jan 29, 2010

  • 3 Answers

SOURCE: Land Rover Discovery I dashboard replacement.

There is a little more to it than that, but not a tough job if you have patience. You will need to remove both 'doors' on the dash-one glovebox, one fuse access panel. on US models, you will need to remove the pass side airbag as well, then 2 bolts that hold a set of relays under the airbag, then 5 bolts that hold a support bracket (also under the pass side airbag-behind glovebox.

Then under the dash at teh outside near the doors, remove 2 sets of 10mm bolts. after than remove 2 sets of 10mm bolts near where the bottom of the dash touches the tranny tunnel. obviously all the center console needs to be removed, and the center panel of the dash, as there are several sets of screws that hold that to the back of the dash.

be patient, take lots of photos of how it goes together, and where the wiring is(was), and this is pretty easy.

Thanks

Posted on Jun 10, 2010

  • 1 Answer

SOURCE: How do you remove the dashboard completely on 2005 ford explorer?

how to remove dash on 2055 ford explorer

Posted on Oct 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 bmw x6 :collision deployed passenger airbag on dashboard. Can i replace the airbag without changing/replacing the dasboard?


the dash pad -upper section to windshield shouldnt have to be unless damaged by deployment the other 3 sections -airbag location the part in line with the ducting and the knee area usually are damaged during deployment and unless you have been trained ir have working knowledge if the air bag system would have a certified trusted auto body shop survey the damage and advise if any under dash damage is present --they can also show a dash break down diagram as well as correctly installing replacement airbag

May 27, 2016 | BMW Cars & Trucks

1 Answer

Replace engine control module 1993 gm sonoma


Why would you have to remove the dashboard.

The Module can be accessed from under the dash on the passenger side.


25350800-kiyu5aqkqelb2o03f4kwguli-3-0.gif

Jan 02, 2015 | 1993 GMC Sonoma Club

1 Answer

Do I have to replace the dashboard when I replace the passenger airbag?


No. the airbag is attached to an insert that is mounted in the existing dash. The colors may not match due to fading.

Nov 12, 2013 | 2000 Lincoln Continental

1 Answer

My air bag light on the dashboard stays on after i disconected my battery on my kia sportage 2007


just remove the battery terminals for a while if the problem remain same than the airbag system needs to replace

Sep 13, 2013 | Cars & Trucks

2 Answers

Was wrecked need to know how to take out the airbag and replace


This process would very depending on each car. Check the fuse box for the airbag fuse. Have it removed before disassembling the airbag assembly. For the driver side airbag... remove the cover of the driver's wheel to gain acces to the assembly. In some cases you will have to remove the cover of the steering columns. For the passenger side airbag you need to remove the dashboard to gain access to the assembly.

Jan 27, 2012 | Cars & Trucks

1 Answer

I HAVE 2 2007 MERCEDES C230 , ONE THE BOTH AIRBAGS EXPLODED, DRIVER AND PASSENGER, CAN I USE THE AIRBAGS FROM THE OTHER MERCEDES?, IS SAME CAR, SAME YEAR, HOW CAN I TAKE THE AIRBAGS? THE PASSEGER AIRBAG...


The airbags will fit and swap over. The drivers airbag can be swapped over by itself.. The passenger airbag you will probably need to change out along with the dash since it rips the dash in order to deploy;. The airbags are considered a safety item and a very crucial item at that. Unless it's your personal vehicle I wouldn't use the airbags out of another vehicle. If you are not familiar with the Mercedes airbag system then I highly suggest you have a trained technician do the work for you. There are two manufacturers for the srs control module and airbags. If you mix the two together they can accidently deploy while driving.

Oct 03, 2010 | Mercedes-Benz C230 Cars & Trucks

1 Answer

How to remove dashboard


1-Remove the vent/radio housing.
2-Remove the cover panels on either side of the dash that get cover when the door is closed.
3-Remove the panel under the steering wheel.
4- Remove glove box to open space inside of dash.
5-Remove four bolts and connector holding passenger side airbag and remove carefully.
6-Remove cover plate over shifter.
7-Remove the center console.(2 bolts under armrest and 4 screws-2 on either side of the console)
8-Disconnect the wiring harnesses on either side of dash.(White and black connectors. 2 on driver 1 on passenger.
9-Remove the four bolts holding the center of the dash to the floor.
10- remove two bolts on drivers side dash where cover was and same on passenger side.
11- Unbolt the steering column ( 2 bolts under the wheel) and let it rest on floor.
12- The entire dash will remove from the car as 1 piece and each component can be taken out from there.

It isn't worth it to fish for the bolts from the inside. Take the support bar out and work on it outside the car. much faster.

It seems confusing, but easy if you take your time

Aug 04, 2010 | 2003 Kia Spectra

1 Answer

Where is the flasher for signal lghts on 04 Impala?


On the Impala the flasher is located behind the dashboard, just to the right of the steering wheel. You have to remove the dashboard to get to it. It square and about 2" long. To remove the dash:
- remove the two fuse compartments doors or lids, that are on either end of the dashboard. there are two screws to remove on both sides.

- Remove the kick plate beneath the dash on the passenger side.
- Remove screws beneath the dash on drivers side
- Adjust steering wheel to the full down position
- Move Shift lever all the way down

May 09, 2010 | 2003 Chevrolet Impala

2 Answers

Land Rover Discovery I dashboard replacement.


There is a little more to it than that, but not a tough job if you have patience. You will need to remove both 'doors' on the dash-one glovebox, one fuse access panel. on US models, you will need to remove the pass side airbag as well, then 2 bolts that hold a set of relays under the airbag, then 5 bolts that hold a support bracket (also under the pass side airbag-behind glovebox.

Then under the dash at teh outside near the doors, remove 2 sets of 10mm bolts. after than remove 2 sets of 10mm bolts near where the bottom of the dash touches the tranny tunnel. obviously all the center console needs to be removed, and the center panel of the dash, as there are several sets of screws that hold that to the back of the dash.

be patient, take lots of photos of how it goes together, and where the wiring is(was), and this is pretty easy.

Thanks

Oct 20, 2009 | 1996 Land Rover Discovery

1 Answer

Broken handle on passenger side dashboard


Quick explanation--you need to remove the lower panel (by your knees), remove any screws that may be holding the vents in place, then carefully pry out vents--it's tight but you can wiggle then out. Now you can see the two 13mm (maybe 15mm) nuts that hold the handle in place. Use a wrench or small ratchet to remove nuts. This part is tough too so keep your 'patience' hat on. 

Dec 13, 2008 | 2000 Chevrolet Astro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...