Question about Cars & Trucks

1 Answer

2012 mazda 6 I touring

Where is tire jack

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 22,258 Answers

I think its under the spare wheel in a sort of round plastic tray thingy

Posted on Apr 28, 2013


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 188 Answers

SOURCE: where do i put the jack to change the tire

there should be a rail on your pickup underneath the sill of the doors, on this rail there are notches cut out, there should be two at the front and the back place your jack here

Posted on Nov 07, 2009

  • 14 Answers

SOURCE: I have a flat tire

if you havent found it yet its in the trunk on your right hand side under the carpet there is a plastic cover, the jack should be there.

Posted on Oct 12, 2011

  • 344 Answers

SOURCE: Honda Odyssey Touring 2010, it received a control tire pressure, or 2012 also has a?

32 (PSI)

Posted on Nov 29, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to reset tire pressure light stays on even after tires is aired up

try disconnecting the battery leave for 20 mins then reconnect.also note that tyre pressure sensors can go faulty and remember its enviroment being attatched to the wheel it can get damaged

Mar 11, 2016 | 2012 Chrysler 200 Touring Convertible 2.4L...

1 Answer

Car wont start at times then it will.then when driving will stop and wont start

does it want to turn over? Any sounds? Might be fuel pump or clogged fuel filter.

May 18, 2015 | 2012 Mazda 3 i Touring 4dr Hatchback 2.0L...

1 Answer

What does a manufacturer warranty cover on a 2012 mazda 6

it really depend what warrant you got when you bought the car.
you can go to mazda website go service ask what part and labor covered for the car you have if you bought it new

if you bought used that you have 6-12 month,
most new car 3 yrs or 36000 miles what ever comes first

if you have bump to bump thats really good
parts that are not covered:
tires, brakes, batteries, lens, light bulbs, thing used under normal where consumables items

you can call the local dealer and ask for service dept, talk with a techn
you will need the VIN number located driver side lower part of the indow

Apr 16, 2015 | Mazda 6 Cars & Trucks

1 Answer

Do you have a diagram for a 2012 Mazda 2 1.5 liter engine for the serpentine belt?

there should be a decal under the hood somewhere that shows the belt routing you will have to look for it.

Feb 01, 2015 | 2012 Mazda 3 i Touring 4dr Hatchback 2.0L...

2 Answers

2012 Mazda 6 won't start. What are the pissible reasons?

There is a recall on 2012 mazda 6 , Here is what I would check out .
Recall Date:
MAR 11, 2014
Model Affected:
2012 Mazda MAZDA6
Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.
Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.
Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.
Potential Units Affected:
Mazda North American Operations

Read more:

Aug 11, 2014 | Cars & Trucks

1 Answer


P1652 Power Steering Pressure Switch Circuit

Apr 30, 2014 | 2012 Mazda 3 i Touring 4dr Hatchback 2.0L...

1 Answer

How to change tail light

Open the trunk and you will see screw underneath the carpet.remove the screw and push the light out.remove the burn bulb and replace with same model # . If the bulb is dual (5W-15W) will have different high on the locking pins. place the light back and tight slightly.DO NOT OVER TIGHT, WILL BRAKE THE KIGHT

Apr 15, 2014 | 2012 Mazda 3 i Touring 4dr Hatchback 2.0L...

1 Answer

Serpentine belt diagram mazda

2012 Mazda 3 I touring Skyactiv - Takes a 38" 6 groove serpentine belt- Very hard to find. The only place I found besides the dealer it Advance Auto but they had to order from the warehouse. There are three grooved pulleys and a smooth tensioner. To relieve the Tensioner you will need a shallow 17MM socket, it is a bit difficult to see, but if you stand on the passenger side the mount point for the socket is to the left of the tensioner shock. The Tensioner shock is just above the smooth tensioner pulley. All the threaded pulleys' (Drive, A/C, and alternator are within the serpentine belt, the tensioner pulley is outside the belt pushing down on the belt. The easiest way to replace this belt, First remove the old belt by placing the socket on the mount point and pulling up on the ratchet towards the rear of the car, then pull belt off. Next remove socket, place the belt over the drive pulley (this is the one on the bottom to the rear of the engine. ( you will see there is another belt on this pulley on the back side.), then put the belt over the A/C pump bottom front. Keep tension on the belt so it stays in place. Now put that socket back on, push up to lift the tensioner pulley and slip the belt over the alternator pulley. Make sure the belt is sitting properly on each pulley and under the tensioner pulley. Good luck. I have run into quite a few problems finding parts and information for this particular model. Good luck. Hope this was helpful

Apr 11, 2014 | 2012 Mazda 3 i Touring 4dr Hatchback 2.0L...

1 Answer

How to replace egr valve on a 04' Mazda6 2.3L

remove the battery wire first and change the egr valve and reset the code

Dec 21, 2013 | 2012 Mazda SPEED3 Touring 4dr Hatchback...

1 Answer

I have a flat tire on my 2004 Mazda 6...Where is the tire jack located?

if you havent found it yet its in the trunk on your right hand side under the carpet there is a plastic cover, the jack should be there.

Dec 13, 2010 | 2004 Mazda 6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides