Question about 1997 Chrysler Town & Country

Open Question

Showing code p0134, p1695, p1698. Why wont it start?

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 5680 Answers

SOURCE: what is code P0134?

Front O2 sensor.

Posted on Apr 27, 2013


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1997Chrysler town and county wont start and when it does it dies right away, when you give it some gas it back fires

Well the starting problem could be fuel related, code 134 is for an open circuit going to the O2 sensor in front of the catalytic converter.
I doubt the code would cause the engine not to start.

Apr 26, 2013 | 1997 Chrysler Town & Country

1 Answer

Car shutting off while driving

Code P1698 means
* P1698 PCM Failure EEPROM Write Denied
* P1698 -No CCD messages from the Transmission or Body Control Module (TCM or BCM) Probably needs a new PCM (Aka computer or ECU)
autocom can help you check your car and clear the fault codes.

May 15, 2012 | 1995 Mitsubishi Eclipse

1 Answer

1999 dodge caravan no i/p but the millage and prnd21 show for a while but soon shut off thought it was the cluster but replaced it and still the same problem also check engine is on with codes p1698 and...

Both codes you have listed are CCD bus communication faults. I find it very unlikely that the ignition switch is the problem. The first thing I would check is the two 10-way connectors located below the battery tray, one gray and one black. What typically happens is that the battery leaks and drips onto these connectors. The "bus" wires also pass through these connectors. I would recommend a thorough inspection of the connectors, even the back portion where the seal is. Clean with electrical contact cleaner and apply a thin coat of dielectric grease. Also check the wires around the connectors to make sure they have not melted together.

Jan 29, 2011 | 1999 Dodge Caravan

1 Answer

Fault code 0134

P0134 Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
Check wiring to Oxygen sensor.

Apr 22, 2010 | 1992 Land Rover Range Rover

1 Answer

Dash guages are not working....getting code p1698 and p1695 could it be a bad ground?

more than likely its the cluster panel they had many issues with these good luck man if u need more advise let me know

Jan 07, 2010 | 1997 Dodge Caravan

2 Answers

P0134 /P0306 Codes on Chevy Truck 1998

in AKO look under Self Help> My Library > Fix Your Car > then go to Chiltons or ARRC link from there.

Jun 22, 2009 | 1998 Chevrolet K1500

1 Answer

2001 dodge ram 2500 diesel with 6spd manual trans. showing fault codes p1698 , p0237 & p0562. the truck will crank but not start. it has two new battery & map sensor.

p0562 is System voltage low
p0237 is Turbo/supercharger boost sensor A circuit low

cannot find a code p1698 but did find a p0698
p0698 is Accelerator pedal position sensor supply voltage to low

Apr 13, 2009 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
1997 Chrysler Town & Country Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides