Question about Cars & Trucks

Open Question

Volvo Fault Codes

I2 fault code

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Volvo 850 fault codes

SRS reset

Posted on Aug 24, 2008

  • 1 Answer

SOURCE: checking the fault codes

Yes.  Next to the ash tray there is a black slide off plate that reveals the OBD I plug.  {1996 and newer can be read with an OBD II reader (read for free at Advance auto or Auto Zone)}  Once you reveal this plug on the 1995, you can plug in a single jumper wire (or even a paper clip) in the #4 and #15 pin hole.  There are two rows of pin holes, count from the upper right to the #4, then on to #15 (which will be the second to last pin hole).  Turn the ignition switch on (motor not running), insert the jumper wire for about 3 to 5 seconds, then remove the wire.  The ENGINE LIGHT will flash a hold, then the code, which will go something like this, flash, flash, PAUSE, flash, flash, PAUSE, flash, PAUSE, flash, flash, flash, flash.  Then it will repeat the codes if you just sit there and observe it.  The code in my example would be a 2214 code.
Below are some code I found on a website.  I hope this helps.  Now I ask that you take the time to answer someone elses question.  Lets all share.  Good luck, "Peace through power and knowledge"

CODE FAULT
0000 End of fault sequence
1111 Bad ground to Electronic Control Unit (ECU) or ECU failure-check grounds or replace
ECU
1119 Transmission Range - Defective wiring. Check for break or short.
1213 Vehicle Speed Sensor (VSS) - Check transmission speed sender wiring and the wiring of
the instrument cluster
1231 Vehicle Speed Sensor (VSS) (G54) - Check transmission speed sender wiring and the
wiring of the instrument cluster
1232 Throttle Position Actuator - Check defective actuator or wiring for break or short.
2111 Engine speed sender. (RPM)
2112 Ignition reference sender
2113 Hall sender - No speed signal from distributor; check Hall sensor and circuits or the
Air-flow sensor plate is not moving freely; adjust potentiometer or lever.
2114 Hall sender not on reference point or distributor out of position.
2121 Idle switch - check switch & circuit.
2122 Hall sender - Check wiring for break or short.
2123 Full throttle switch; check switch & circuit.
2132 Electronic Control Module (ECM) - No ignition to injection signal.
2141 Knock sensor 1 control at maximum ****** - test compression, change octane, adjust
timing, check knock-sensor wires.
2142 Knock sensor 1 signal - Test sensor, check wiring for break or short.
2143 Knock sensor 2 control at maximum ****** - test compression, change octane, adjust
timing, check knock-sensor wires.
2144 Knock sensor 2 signal; test sensor.
2212 Throttle Potentiometer - Value out of range.
2214 RPM Signal - Idle speed to high or engine over-revved
2221 Vacuum Control - No vacuum to control unit. Check for leaks.
2222 Manifold Vacuum - Check vacuum line and wastegate for leaks.
Pressure sensor - Sensor defective
2223 Altitude Sensor - Check sensor, check wiring for break or short.
2224 Turbo/Manifold pressure - Check turbo control wiring, check for over boost, air leak,
defective wastegate valve, vacuum leak or defective pressure sensor.
2231 Idle-speed stabilizer adjustment limits exceeded; too-fast idle. Adjust throttle for full
closing, check for vacuum leak, check ignition timing.
Or
Air Mass Sensor - Check sensor and wiring.
2232 Air mass/flow sensor - No signal. Check wiring for break or short.
2233 Air mass/flow sensor reference voltage open or short circuit
2234 ECM Supply voltage low.
2242 CO-potentiometer voltage low
2312 Coolant temperature sensor - Check wiring, check resistance.
2314 Transmission to Engine control module circuit. - Check wires for breaks or shorts.
2322 Intake Air Temperature Sensor - Check sensor and wiring.
2323 Mass Airflow Sensor - Check sensor and wiring for breaks.
2324 Mass Airflow Sensor - Check sensor and wiring for breaks or shorts to B+ or ground or
check for air leak.
2331 Oxygen Sensor Control - Out of range. - Check ignition, air intake for leaks and injectors.
2332 Oxygen Sensor - Bank 2 - Check wiring for breaks or shorts.
2341 Oxygen sensor (O2) at control limit; check CO, lambda-sensor wire, lambda-sensor
control, start valve, evaporative system and check for vacuum leaks.
2342 Oxygen Sensor Control - no signal - Check wiring, sensor.
2343 Rich limit; the pressure regulator has exceeded +10 mA for more than 5 minutes,
closed-loop; check for vacuum leaks.
2344 Lean limit; the pressure actuator has exceeded -5mA for more than 5 minutes, closed
loop; check idle.
2411 EGR System Malfunction
2412 Intake Air Temperature Sensor - Check sensor and wiring for breaks or shorts
2413 Mixture Control - Running rich
Fuel pressure too low
3424 Malfunction Indicator Lamp (MIL) failure - Check lamp and wiring.
4311 Secondary Air Injection Pump Relay - Check relay and wiring.
4312 EGR Frequency Valve
4313 Secondary Air Injection Solenoid Valve - Check valve and wiring.
4331 EVAP Carbon Canister Solenoid Purge Valve 2
4332 Ignition Circuit Final Stage - Check for break or short to ground or B+ or bad ECM.
4343 EVAP Carbon Canister Solenoid Purge Valve 1
4411 Fuel Injector Cylinder 1 or 1 & 5
4412 Fuel Injector Cylinder 2 or 2 & 7
4413 Fuel Injector Cylinder 3 or 3 & 6
4414 Fuel Injector Cylinder 4 or 4 & 8
4421 Fuel Injector Cylinder 5
4422 Fuel Injector Cylinder 6
4423 Fuel Injector Cylinder 7
4424 Fuel Injector Cylinder 8
4431 Idle Air Control Valve / Idle Stabilizer - Check valve and wiring.
4433 Fuel Pump Relay
4442 Wastegate - Defective frequency valve or wiring.
Boost pressure circuit - Check for short.
4443 EVAP Canister purge valve.
4444 No fault in system.

Posted on Oct 19, 2008

  • 99 Answers

SOURCE: 1999 DODGE CUMMINS SHUT DOWN FAULT CODES p1689, P1688

P-1689 NO COMMUNICATION BETWEEN ECM & INJECTION
PUMP MODULE

Posted on Jul 21, 2009

BCAS1298
  • 3092 Answers

SOURCE: My VW Eurovan,2002 has 2 fault codes. P0011 and

P0011 - Intake camshaft position timing ( over advance bank 1 )
O0420 - catalyst system efficiency below threshold bank 1. Hope this was helpful.

Posted on Dec 02, 2009

  • 1 Answer

SOURCE: Fault codes and how do you read them

Do you need to know how to manually pull the codes?

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Check engine ecu light keeps comming on 2006 volvo


Get OBD (on board diagnostic) from auto zone and plug it into car to read error codes.

Oct 08, 2014 | Volvo Cars & Trucks

1 Answer

2007 Volvo XC90 fault codes-ECM P030000, P030100, P030300, P0304000, what do they mean?


first code means random/multiple misfire cylinder (s) detected
second code means misfire detected number 1 cylinder, third code, miss=fire number 3 cylinder fourth code misfire number 4 cylinder
causes can be spark plugs, HT leads, ignition coils, injector, wiring fault, low compression/ engine mechanical fault

Jun 04, 2010 | 2007 Volvo XC90 V8 AWD Sport

3 Answers

Volvo v70, rough running, fault codes p2172 p2101


The exact same set of codes have just come up on my car, the same car and year. Did you solve it? I am thinking cleaning the throttle body first, any help appreciated....

Jun 02, 2010 | 2002 Volvo V70

1 Answer

Volvo xc70 in limp mode 7 fault codes recorded d5


Possible problem with the alternator not putting out enough voltage. I had the same problem with my 2002 XC70, putting in a new alternator fixed it. I used a local mechanic who I found on the car talk web-site. Low Cost Volvo parts can be purchased at FCP Groton.

Apr 22, 2010 | 2003 Volvo XC70

2 Answers

Fault codes on a volvo FH12 rear left lights stay on


Volvo has had a lot of trouble with relays in the rear control module. Check/replace the relays for the rear lights with the updated relays.

Mar 20, 2010 | 2004 Volvo XC70

1 Answer

6720, A011, 112B, 4490, 5F11,1144 - Volvo XC90 -


here is the fault read out page for most volvos http://volvospeed.com/vs_forum/index.ph ... =66705&hl=
hope this works for you if not send email to me griff842000@yahoo.com

Sep 28, 2009 | 2005 Volvo XC90

1 Answer

2002 Volvo S60 with Engine fault codes


THE 445 IS THE EVAP PURGE VALVE IT MAY BE BAD BOTH 446 IS SAME VAVLE YOU NEED TO SEE IF THE HOSE ARE GOOD ON THIS VAVLE MAKE SHERE NO CRACKS IF NOT PULL HOSES AND SEE IF SOMTHING IN VAVLE ITS NEAR THE CANSTER AND THAT IS NEAR THE GAS TANK UNDER CAR PUT CHECK GAS CAP MAKE SHERE ITS TIGHT HOPE THIS HELPS

Sep 15, 2009 | 2002 Volvo S60

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...