Question about 1999 Plymouth Grand Voyager

1 Answer

Battery cable Where is the starter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 1,209 Answers

At the end of the positive battery cable.

Posted on Apr 26, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i know if my starter relay is bad on a dodge stratus 2001


IF STARTER RELAY BAD THE STARTER WONT MAKE NO NOISE AT ALL HEADLIGHTS WONT DIM.IF YOU CLICKING NOISE BATTERY VOLTAGE TOO LOW. MAKE SURE BATTERY VOLTS ARE 12.6 VOLTS AND USE TEST LIGHT TO SEE IF STARTER GETTING POWER.COULD HAVE BLOWED IGNITION FUSE OR FAULTY IGNITION SWITCH. TO CHECK STARTER SOLENOID FIRST TURN OFF RADIO THEN REMOVE NEGATIVE BATTERY CABLE AND POSITIVE BATTERY CABLE.THEN REMOVE STARTER BUY A REMOTE SWITCH.YOU NEED BATTERY JUMPER CABLES HOOK BATTERY JUMPER CABLES TO BATTERY PUT POSITIVE CABLE ON POSITIVE BATTERY POST THEN PUT NEGATIVE BATTERY CABLE ON NEGATIVE POST. HOOK BATTERY CABLES TO STARTER USE NEGATIVE CABLE GROUND STARTER BODY AND PUT POSITIVE BATTERY CABLE ON THE LARGE POSITIVE POST ON STARTER SOLENOID. NOW TAKE REMOTE SWITCH HOOK RED WIRE TO STARTER SOLENOID POSITIVE POST THEN HOOK BLACK WIRE TO REMOTE SWITCH TO STARTER SOLENOID SWITCH TERMINAL WITH LETTER S THEN PRESS REMOTE IF STARTER SPINS STRONG WITH A GOOD KICK STARTER GOOD.YOUR PROBLEM COULD BE CORRODED WORN BATTERY CABLES. WEAK BATTERY FAULTY IGNITION SWITCH. IF STARTER DONT WORK WHEN YOU PRESS THE REMOTE SWITCH STARTER SOLNOID BAD OR STARTER ITSELF BAD.IF ALL IS GOOD. CODE SCAN CAR FOR THEFT SECURITY FAULT CODE.

Aug 28, 2011 | 1999 Dodge Caravan

2 Answers

Truck will not start how can i tell if its a starter or selonoid


does it spin real fast without clanging and grinding against the flywheel? if so then its probably the solenoid bad. do you have to hit the starter with a hammer then it works? it is probably bad brushes or a worn motor. eather way i think you can only get a new starter and solenoid together not sold seperate. check for bad battery cables (loose).

May 30, 2011 | 1996 Chevrolet K1500

1 Answer

I have a gmc 1998 turbo diesel that cranks but wont turnover or try to..i have replaced the supply pump as well as the inline pump..what can i do to get my truck started ..thank you ?


TURN OFF RADIO FIRST TO KEEP FROM LOCKING IT OUT WHEN YOU DISCONNECT NEGATIVE BATTERY CABLE. SOUND LIKE WEAK BATTERY OR STARTER MAKE SURE BATTERY CABLES CLEAN AND TIGHT.IF BATTERY GOOD REPLACE BATTERY CABLES.CHECK STARTER MAKE SURE STARTER SOLENOID AND STARTER OKAY.YOU CAN HAVE THEM TESTED AT AUTO PARTS STORE OR USE A REMOTE SWITCH.REMOVE STARTER FROM VECHICLE USE JUMPER CABLES.HOOK NEGATIVE GROUND CABLE TO BATTERY NEGATIVE THEN GROUND STARTER BODY WITH NEGATIVE BATTERY JUMPER CABLES HOOK POSITIVE JUMPER CABLE TO BATTERY POSITIVE AND STARTER POSITIVE TERMINAL.THEN HOOK REMOTE SWITCH TO STARTER STARTER SWITCH AND OTHER REMOTE WIRE TO STARTER POSITIVE TERMINAL.PRESS REMOTE STARTER WILL SPIN IF GOOD.MAKE SURE INJECTION PUMP STATIC AND DYNAMIC IS TIMING CORRECT BEFORE STARTING TRUCK.

Dec 07, 2010 | 1998 GMC Sierra

1 Answer

How to get to starter on 2003 traikblazer


Removal & Installation 4.2L Engine To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Disconnect the brake booster hoses from the engine. Starter gm-02-42-1398.gif

  3. Remove the positive battery cable and s-terminal lead from the starter.
  4. Remove the starter from the engine.
To Install:
  1. Install the starter to the engine. Tighten the nut and bolt to 37 ft-lb (50 Nm).
  2. Install the positive battery cable and s-terminal to the starter. Tighten the battery cable nut to 80 in-lb (9 Nm). Tighten the s-terminal nut to 20 in-lb (2.3 Nm).
  3. Connect the vacuum brake booster hose to the engine.
  4. Connect the negative battery cable to the battery.
5.3L & 6.0L Engines To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Raise and support the vehicle.
  3. Remove the rear steering gear crossmember from the frame. Starter gm-02-53-1399.gif

  4. Detach the wire harness from the transmission oil cooler line bracket.
  5. Detach the transmission oil cooler line bracket from the engine.
  6. Remove the right transmission cover bolt from the transmission cover.
  7. Detach the starter from the engine.
  8. Slide the starter forward and remove the transmission cover.
  9. Remove the heat shield from the starter.
  10. Position the starter so that it can pass between the engine oil pan and transmission oil cooler lines.
  11. Detach the starter lead and battery positive cable from the starter.
  12. Remove the starter from the vehicle.
To Install:
  1. Place the starter between the engine oil pan and transmission oil cooler lines.
  2. Attach the battery positive cable to the starter and starter lead. Torque the battery positive cable nut to 80 in-lb (9 Nm). Torque the starter lead nut to 30 in-lb (3.4 Nm).
  3. Install the heat shield to the starter.
  4. Attach the starter from the engine. Torque the bolts to 37 ft-lb (50 Nm).
  5. Install the right transmission cover bolt into the transmission cover. Torque the bolt to 80 in-lb (9 Nm).
  6. Attach the transmission oil cooler line bracket to the engine. Torque the bolt to 80 in-lb (9 Nm).
  7. Attach the wire harness to the transmission oil cooler line bracket.
  8. Install the rear steering gear crossmember onto the frame.
  9. Lower the vehicle.
  10. Connect the negative battery cable to the battery.
prev.gif next.gif

Aug 19, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

Where is my starter and how do I change my starter?


2000 Hyundai Elantra 2.0L MFI DOHC 4cylRemoval & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
  3. 2e15922.jpg

    Fig. Exploded view of the starter-XG 300 and XG 350

To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable.

All Others
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable and wait at least 3 minutes Speedometer cable and shift cable from the transaxle Starter motor wiring Starter motor bolts and the starter
To install:
  1. Installation is the reverse of removal. Tighten motor retainers to 20-25 ft. lbs. (27-34 Nm).

Hope helps (remember rated this).

Jul 14, 2010 | 2000 Hyundai Elantra

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

1 Answer

Where is starter on 2002 honda crv?


Honda_Cr-V_2001-2006
Starter - Removal & Installation

2.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Starter wiring harness connectors Starter motor

To install:
  1. Install or connect the following:

    Starter motor. Tighten the bolts to 33 ft. lbs. (44 Nm). Starter wiring harness connectors. Tighten the battery cable nut to 79 inch lbs. (9 Nm). Negative battery cable

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Knock sensor connector Starter wiring harness connectors Starter motor

    8b26da5.jpg
    Fig. Starter mounting

To install:
Install or connect the following:

Starter motor. Tighten the upper bolt to 33 ft. lbs. (44 Nm); the lower bolt to 47 ft. lbs. (64 Nm). Starter wiring harness connectors. Tighten the battery cable nut to 84 inch lbs. (9 Nm). Knock sensor connector Negative battery cable


Hope this help (remember comment and rated this).

Apr 04, 2010 | 2002 Honda CR-V

2 Answers

Having electrical starter problems. Have replaced


when the problem occurs,take a test light and see if you have power to the starter solenoid. if you do, you have a defective starter. most starters are rebuilt,not new and there are always clunkers. good luck

Mar 14, 2010 | 2002 Nissan Frontier Crew Cab

1 Answer

How do I replace the starter on my 2004 Grand Am?


Alero, Grand Am 1999-2005 Repair Guide
Starter - Removal & Installation

2.2L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Starter electrical connector Starter motor

    781094e.jpg

    Fig. Starter mounting-2.2L engine
To install:
  1. Install or connect the following:
    Starter motor. Torque the bolts to 30 ft. lbs. (40 Nm). Starter electrical connectors Negative battery cable

3.1L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Starter electrical connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor. Torque the bolts to 32 ft. lbs. (43 Nm). Starter electrical connectors Negative battery cable
3.4L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Flywheel inspection cover Starter electrical connectors Starter motor
To install:
Install or connect the following:
Starter motor. Torque the bolts to 32 ft. lbs. (43 Nm). Starter electrical connectors Flywheel inspection cover. Torque the bolts to 89 inch lbs. (10 Nm). Negative battery cable


I hope helps with this. Good luck (remember rated this help).

Dec 29, 2009 | 2004 Pontiac Grand Am

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

Not finding what you are looking for?
1999 Plymouth Grand Voyager Logo

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...