Question about 1997 Chrysler Town & Country

1 Answer

What is code P0134?

Vehicle wont start

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 5,618 Answers

Front O2 sensor.

Posted on Apr 27, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault code P0134


P0134 fault code means that the front oxygen sensor does not work. When the engine starts, the engine computer to monitor the input voltage before the oxygen sensor, if the signal voltage from the sensor within the specified time is less than 0.5V, the computer determines the sensor does not work, probably because the engine computer failure, sensor failure, between line failure, exhaust system leaks, etc., are generally sensor damage. To the service shop using the obd2 scanner can be judged. hope the answer to help you.

Dec 20, 2013 | Cars & Trucks

1 Answer

1997Chrysler town and county wont start and when it does it dies right away, when you give it some gas it back fires


Well the starting problem could be fuel related, code 134 is for an open circuit going to the O2 sensor in front of the catalytic converter.
I doubt the code would cause the engine not to start.

Apr 26, 2013 | 1997 Chrysler Town & Country

1 Answer

I am getting codes p0141 and p0134, and I have replaced the sensor 1 upstream already


P0141 Heated o2 sensor. P0134 Heater 02 sensor circuit, These 02 sensor has a fuse in the engine junction box listed as IGN 1. This supplies 12volts to the heater circuit, check to make sure its not a open fuse. If you already replaced the sensors make sure you clear the code. or it will stay in memory.

Apr 13, 2012 | 2003 Pontiac Montana

1 Answer

2000 Ford Windstar 3.8.....engine light is on.....have been told that the following codes show up........P1171, P1175, P0131, P0134......what does it all mean and how much would it cost to correct?.....my...


After researching the codes you posted, I could only find only the last two, are you sure that the first two are in the correct sequence? however I did find a code P1117 and P1157.

Your stored codes P 131, P0134 are in reference to your 02 sensors, this may be due to faulty sensor input, ie: coolant sensors.

You will almost likely have to use a scanner to take the readings from your vehicle.

Jun 13, 2011 | Ford Windstar Cars & Trucks

1 Answer

P0134 doesn't necessarily mean a sensor is 'bad'. Oxygen sensors on the exhaust detect emission irregularities caused by air/fuel ratios that are out of accepted parameters that are programmed into the...


Dont mean to be a prude but that diagnosis is incorrect. A fouled spark plug, vacuum leak, ect.. will not trigger this diagnostic code alone. If in fact you had a fouled plug or vacuum leak the P0134 code would be followed with another diagnostics code. If the P0134 code is the only code pulled then this code is triggered by the voltage of the o2 sensor being 3V or higher. The front heated oxygen sensor (or sensor 1) is placed into the exhaust manifold. It detects the amount of oxygen in the exhaust gas compared to the outside air. The heated oxygen sensor 1 has a closed-end tube made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. The heated oxygen sensor 1 signal is sent to the The ECM adjusts the injection pulse duration to achieve the ideal air-fuel ratio. The ideal air-fuel ratio occurs near the radical change from 1V to 0V.

The causes for this code:
- Harness or connectors (The sensor circuit is open or shorted)
- Front Heated oxygen sensor (Bank 1) may be faulty

To correct this code:
- Replacing the O2 Sensor 1 usually takes care of the problem.
- Replace the damaged harness or connectors.

Jan 16, 2011 | 2003 Honda CR-V

1 Answer

Fault code 0134


P0134 Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
Check wiring to Oxygen sensor.

Apr 22, 2010 | 1992 Land Rover Range Rover

2 Answers

P0134 /P0306 Codes on Chevy Truck 1998


in AKO look under Self Help> My Library > Fix Your Car > then go to Chiltons or ARRC link from there.

Jun 22, 2009 | 1998 Chevrolet K1500

1 Answer

P1133 and p0134 code


Code P0134 is the #1 oxygen sensor on bank 1, up near exhaust manifold.
Code P1133 is insufficient switching of bank 1 02 sensor. Need to replace it.

Apr 03, 2009 | 1996 Chevrolet Cavalier

Not finding what you are looking for?
1997 Chrysler Town & Country Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...