Question about 2001 Dodge Intrepid
How do I replace a fuel kit on a 2001 dodge intrepid? Thank you
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
the easiest way is going to first be to remove the serpentine belt which requires you to loosen the nut on the end of the idler pulley just above the alternator, then behind the pulley is a bolt with a 13mm head on it that you will want to loosen after the pulley is loose to relieve tension off the belt. Remove the belt. Next make sure you remove the battery cables to ensure you dont fry yourself to the car when unhooking the electrical connections from the alternator, your battery is located on the passenger side, down behind and underneath the headlight. Then go under the car and remove the black plastic clips that hold the splash shield up under the bumper. After this the alternator becomes as accesible as it can be, remove it from the bottom. Thanks for using fixya!!
Posted on Mar 15, 2009
make sure you get the right pump, you need to know your tank size. then take off your bed. you have i believe 6 bed bolts, disconnect tail lights (unplug from underneath) remove bed grounding strap 1 screw, remove bed with help. Disconnect wires, unscrew fuel pump, replace pump. Reverse order to replace bed. jim
Posted on Jun 26, 2009
Start by safely raising the rear end of the vehicle well above the ground. Note: it is best to change the fuel pump with as little fuel in the tank as possible. Once under the car locate the fuel tank and remove the large filler tube going into the side of the tank. Also, if equipped, remove the smaller tube next to the filler tube. Then, remove the two bolts furthest to the rear of the vehicle that are retaining the fuel tank hanger brakets. This should allow the tank to sag down in the rear end, allowing you access to the fuel pump wiring harness, vent tube, pressure line, and return line. Remove all of these carefully. Note beware of residule fuel pressure in the lines, also the fuel lines may require special disconnect tools to unfasten them from the pump assy. With all lines, tubes, and wiring removed from the tank, remove the brackets from the tank and manuver the tank to the ground. Move it to a well ventailated spot and then use a flat tip screw driver and a hammer to work the fuel pump assy. retainer nut couter clockwise off of the tank. Remove the pump assy. from the tank carefully and replace. Reverse procedure to reinstall. When attempting to start the vehicle the first time after service cycle the ignition key back and forth from the locked to the on position at least three times in order to prime the fuel system, as there is no fuel pressure in the lines following there removal. Also be sure to check closely for leaks once the vehicle is running. Then watch closely when adding fuel for the first time following service to ensure a proper seal at the filler tube.
Posted on Oct 24, 2009
The first step is turning the car off. Then before turning the key back on, push and hold the Eject button then turn the ignition on. If the CD fails to eject then you can use a old CD and try to insert it into the CD Player, just as it try's to take your second CD pull it out and hit the Eject button again. This will usually get a Dodge CD player to Eject.
If this fails then the CD player must be removed and a manual eject can be performed.
Posted on Jul 29, 2010
Tips for a great answer:
Aug 30, 2014 | 2001 Dodge Intrepid
Apr 18, 2014 | 2001 Dodge Intrepid
Oct 07, 2013 | 2001 Dodge Intrepid
Feb 07, 2013 | 2001 Dodge Intrepid
Jan 19, 2013 | 2001 Dodge Intrepid
Jan 14, 2013 | 2001 Dodge Intrepid
Sep 03, 2010 | 2001 Dodge Intrepid
Nov 03, 2009 | 2001 Dodge Intrepid
116 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: