Question about Subaru Legacy

Open Question

Transmission pan bolt specs - Legacy Subaru Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75744 Answers

SOURCE: Transmission toque specs

The spec is 12 ft lbs of torque. Use a an even pattern when you tighten the bolts, this assures the gasket will not be damaged and create another leak.

Posted on Jul 27, 2008

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

moparownr
  • 667 Answers

SOURCE: Need torque specs for oil pan bolts

torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

Posted on May 22, 2009

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the transmission gasket on a 1988 chevy Silverado


Raise vehicle and support on jack stands. Loosing nuts on transmission making one side lower than the other this will allow you to drain fluid. Drain fluid remove bolts on pan. Remove pan remove old gasket, clean pan and transmission edge, replace with new gasket. Replace pan and bolts. Torque to spec and refill transmission

May 05, 2016 | Cars & Trucks

1 Answer

2007 pontiac g6 transmission filter replacement


Remove the transmission pan - some don't have drain plugs, have a big pan underneath to catch the fluid. Pull filter and install filter on. Clean any debris from pan. Install gasket onto pan and install pan back onto transmission. Torque bolts to factory specs. Fill with approved ATF.

Hope this is helpful :-)

-Scott
25449121-csuuapdgb0syz0ddt50mju2i-5-0.jpg
Pontiac G6 GT Trans Fluid and Filter Change time lapse GoPro

Feb 19, 2015 | 2007 Pontiac G6 GTP

1 Answer

Tourqe specs for transmission pan bolts 2005 town and country


i need torque spec on 2005 chrysler town and coutry van for transmission bolts are 10 m

Dec 31, 2012 | 1997 Chrysler Town & Country

2 Answers

How can I change the transmision fluid in my 2005 chevy equinox?


Most transmission pans do not have a drain plug. To drain the transmission the velicle will have to be raised. I usually set a large drain pan-several quarts in size-under a rear corner of the transmission pan. I loosen about three bolts on the corner so the transmission fluid will drain. When drained, I remove the rest of the bolts-all 32 or more of them. With the pan off check the color of the fluid look for burnt looking fluid. See if the fluid smells burnt. If so you may have other transmission problems. Look for metal pieces in the transmission pan another indicator of other problems. Clean all the old gasket from the pan and transmission housing-be careful not to gouge either the pan or housing. I use my finger or thumbnail if possible. Gouging either of these places will cause leaks. If you're going to replace the screen do so now. Place the new pan gasket on the pan. Check with the manufacturer's specs before using any permatex or other silicones to hold the pan gasket. I always slide a bolt or two through the pan and gasket holes, lift the pan, and start the bolts. Go slow. Make sure each bolt is going through the gasket hole before tightening it to the transmission housing. Replace the bolts and tighten to a snug using a criss-cross pattern. Go back and forth across the pan tightening each bolt a few turns until all are tight. Don't overtighten the bolts. Doing so will damage the pan gasket, When all bolts are tight, refill the transmisson slowly checking for leaks. Fill the transmission to manufacturer's specifications.

Feb 26, 2011 | Chevrolet Equinox Cars & Trucks

1 Answer

What is the oil pan bolts torque spec for a 2002 jaguar X-type V-6


Fig. Oil pan bolt torque sequence-X-Type

b8259f9.jpg



  1. Use a new oil pan gasket. Tighten the bolts, in the sequence shown, to 18 ft. lbs. (25 Nm).
  2. Tighten the pan-to-transmission bolts to 33 ft. lbs. (45 Nm).
  3. Tighten the access cover bolt to 89 inch lbs. (10 Nm).
  4. Tighten the compressor bolts to 18 ft. lbs. (25 Nm).
  5. Refill the engine with oil.
  6. Install the transfer case.
Hope this helped (rememer comment and rated this).

Apr 14, 2010 | 2002 Jaguar X-Type

1 Answer

What are the torque specs for transmission pan bolts on 2003 maxima


hello! the torque specs on transmission oil pan are 62 to 80 inch pounds or 7 to 9 newton meters. hope this information helps you!

Sep 17, 2009 | 2003 Nissan Maxima

1 Answer

Oil and transmission pan bolt torque specs


124 inch lbs on oil pan...Transmission pan 13 ft lbs.

May 06, 2009 | 1991 Buick Park Avenue

1 Answer

Transmission toque specs


The spec is 12 ft lbs of torque. Use a an even pattern when you tighten the bolts, this assures the gasket will not be damaged and create another leak.

Jul 27, 2008 | 2003 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...