Question about 2004 Dodge Dakota

Open Question

How to repair dodge dakota tilt steering column

The steering column is locked what do I do

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Cannot get to heater blower motor in 1993 Dodge Dakota

its a big job get yourself a hanes manual the module is the complete heater box underdash you have to pump down a/c. i put heater core and blower motor in a 95 dakota its not a fun thing to do

Posted on Dec 17, 2008

  • 60 Answers

SOURCE: steering come and goes.no fluid lost. no noise 2004 Dodge Dakota

the power steer pump is faulty

Posted on Aug 07, 2009

morse008
  • 1111 Answers

SOURCE: how is the steering column tilt lever removed?

you can turn the steering wheel to one side that a flat spot allows you access to it with a torque screw {star} shaped the other is on top as well a screw to the harness way under the dash removal of the lower panel is recommended for access

Posted on Jan 06, 2010

  • 204 Answers

SOURCE: 98 dodge dakota steering noise

take a look at your cv joints

Posted on Feb 03, 2010

  • 1 Answer

SOURCE: 1987 dodge ram van STEERING COLUMN

to whom this may concern did you find a steering column. Are you replacing it in a 1987 dodge pick-up

Posted on Feb 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need help replacing steering column in 1988 dodge dekota


Yes you can replace the tilt column with a straight standard column on an 88 Jeep Wranger, it is a simple bolt in swap. Make sure you don't pinch any of the wires while swapping and it cause a bunch of headaches.
----------------------------------------------------------------------------------------

New Arrivals
Emergency power supply

Jan 15, 2013 | 1988 Dodge Dakota

1 Answer

Steering column loose


You need to rebuild the steering column and tighten all the tilt parts up that have worked loose over the years.
Here is a guide to do that. The video at this link is of a truck repair but the columns are the same in both and use the same procedures and special tools to repair.

Jul 22, 2012 | 1994 Buick Skylark

1 Answer

95 dakota


Ground fault in the column is likely to blame...and a pain to fix.

May 01, 2012 | Dodge Dakota Cars & Trucks

1 Answer

Steering column is very loose; so do I replace it or can it be repaired without removing it? Where can I see the photos or diagrams of the steering column?


Would help to know what column. Is it the old round column???
Is it tilt and is it moving about where it tilts?
If yes, the column can stay in the vehicle. You will need some specific tools to do this. Amoung other tools you need, a steering wheel puller, Lock plate tool, possiby male torx bits/drivers (depending on year), for certain torx female socket and a tilt pin removal tool.

And it is somewhat a complex job for someone that has not done it before.

Sep 07, 2011 | Chevrolet Silverado Cars & Trucks

1 Answer

How do i remove the steering column cover to get at the ignition tumbler on a 1993 dodge dakota


CAUTION Disconnect and isolate the negative (ground) battery cable. This will disable the air bag system. Failure to disconnect the battery could result in accidental deployment and possible personal injury. Allow the system capacitor to discharge for two minutes then begin air bag system component removal. To install:
  1. Engage the electrical connectors to the ignition switch and make sure the switch locking tabs are fully seated.
  2. Before attaching the ignition switch to a tilt steering column, the transmission shifter must be in the PARK position. Also the park lock dowel pin and the column lock flag must be properly indexed before installing the switch as follows:
    1. Place the transmission shifter in the PARK position
    2. Place the ignition switch in the LOCK position. The switch is in the lock position when the column lock flag is parallel to the ignition switch terminals.
    3. Position the ignition switch park lock dowel pin so it will engage the steering column park lock slider linkage.
    4. Apply a light coating of grease to the column lock flag and the park lock dowel pin.
  3. Place the ignition switch against the lock housing opening on the steering column. Ensure that the ignition switch park lock dowel pin enters the slot in the park lock slider linkage in the steering column.
  4. Install the retaining bracket and ignition switch mounting screws, then tighten the screws to 22-30 inch lbs. (3-4 Nm).
  5. If the vehicle is equipped with a tilt steering column, install the tilt lever.
  6. With the key cylinder and the ignition switch in the LOCK position, insert the key cylinder into the ignition switch until it bottoms.
  7. Insert the ignition key into the lock cylinder. While pushing the key cylinder in toward the ignition switch, rotate the ignition key until the end of travel.
  8. Install the retaining screw into the bracket and lock cylinder. Tighten the screw to 22-30 inch lbs. (3-4 Nm).
  9. Install the steering column covers, then the tilt lever, if equipped.
  10. Connect the negative battery cable.
  11. Check for proper operation.


ec3f7ac.jpg

eff2c5f.jpg

72e2667.jpg

7a1362b.jpg

Jul 30, 2010 | 1993 Dodge Dakota

2 Answers

How is the steering column tilt lever removed? On a Dodge Dakota 1997 pickup the tilt lever needs to be removed to remove the plastic covers to get to the wiper/ turn indicator switch which I need to...


yes it just threads in look for a flat section down by the column where it screws in this is the best place to put a small wrench and turn it,should come right out after a few twists.

Jan 04, 2010 | 1998 Dodge Dakota

3 Answers

1989 GMC Sierra 3500 loose tilt steering column


Watch videos on youtube ( repairing loose tilt wheel)

Jul 19, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

Replace Blinker arm on 1987 Dodge Dakota


Sorry, when mine went out last year it was IMPOSSIBLE (2 Dodge dealerships, 2 different auto parts chains, and 3 repair shops) to find a replacement.

Had to replace the entire steering column from a junkyard.

Good luck!

Jun 05, 2009 | 1987 Dodge Dakota

Not finding what you are looking for?
2004 Dodge Dakota Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...