Bezel removal how do i take the bezel off

The best I can offer is for a 1996 caravan:

REMOVAL

1. Remove steering column cover.
2. Remove over steering column bezel.
3. Remove left end cover.
4. Remove screw at left end of cluster bezel and headlamp switch.
5. Remove screws holding cluster bezel to instrument panel from each side of steering column.
6. Disconnect clip holding cluster bezel to instrument panel from above right vent louver.
7. Separate cluster bezel from instrument panel.

Disconnect wire connectors from back of the bezel.

INSTALLATION

1. Connect wire connectors into back of the bezel.
2. Place cluster bezel in position on instrument panel. Use care not to place hands on louvers.
3. Connect clips to hold cluster bezel to instrument panel. Use care not to add pressure on the A/C louvers to seat the cluster bezel clips.
4. Install screws to hold cluster bezel to instrument panel on each side of steering column.
5. Install screw at left end of cluster bezel and headlamp switch.
6. Install left end cover.
7. Install over steering column bezel.
8. Install lower steering column cover.

Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Remove front door handle bezel screw cover Remove inside handle bezel screw Remove inside handle bezel Lift upward on the rear of the front door inside handle bezel Disconnect electrical connector Remove handle screw cover
Remove handle screw Remove door trim panel upper screw Remove door trim panel lower screw Remove door trim panel (pull the door trim panel outward to release the pin-type retainers)Remove front door sail panel
Disconnect mirror electrical connector Remove 3 exterior mirror nuts and exterior mirror

1. Disconnect the negative battery cable. Important: When removing a door trim panel or switch plate, disconnect the negative battery terminal. This will eliminate the possibility of shorting out the switch if you use a screwdriver, an awl, or other metal object in order to remove the switch from the harness.
2. Remove the window regulator handle, if equipped.
3. Remove the front door warning reflector.
4. Remove the door panel screw (1) through the hole in the door warning reflector opening.
5. Use a flat bladed tool in order to remove the rear deck release switch bezel.
6. Disconnect the rear deck release switch.
7. Use a flat-bladed tool in order to remove the lower switch bezel trim screw access cover.
8. Remove the lower switch bezel trim screws.
9. Remove the lower switch bezel
10. Use a flat-bladed tool in order to pry the front door switch bezel upward.
11. Disconnect:

1. Gently disengage the front door trim retaining clips and remove the door trim panel from the door.

Installation Procedure

1. Install the front door trim panel to the door. Ensure that the retainers are locked into place.
2. Connect the rear deck release connector.
3. Install the rear deck release switch bezel. Press the bezel firmly into place.
4. Install the window regulator handle to the door.
5. Connect:

• lock switch connector, if equipped.
• Power window switch connector, if equipped.
• Power mirror switch connector, if equipped.

1. Install the front door switch bezel assembly to the front door trim panel.
2. Install the lower switch bezel trim panel. Notice: Refer to Fastener Notice in Service Precautions.
3. Install the lower switch bezel trim screws.
4. Install the lower switch bezel trim screw access cover.
5. Install the door trim panel screw (1) through the hole in the front door warning reflector.
6. Install the front door warning reflector.
7. Connect the negative battery cable.

The seal in the bezel is probably dried and cracked.The bezel and lenze are easy to romove. Just turn it until the teeth line up in the back and it should pop loose. -------- Remove the instrument panel top cover.Remove the screws and remove the cluster bezel. Check out.Thanks.Keep updated.

REMOVAL & INSTALLATION 1984–88 Vehicles

1. Open the hood, then turn the headlights on.
2. Detach the headlight motor wire on the outer side of the headlight.
3. Turn the headlights off (the disconnected light should stay open).
4. Unfasten the 4 screws at the bezel. There are 2 at the front and 2 at the sides. Fig. 1: With the hood in the raised position, unfasten the Torx® screws from the outer side of the headlight bezel/trim piece
   Fig. 2: You must then remove the screws from the inner side of the bezel/trim piece
   
   
5. Remove the bezel. Fig. 3: Remove the first of the top bezel/retaining ring screws . . .
   Fig. 4: . . . then remove the remaining Torx® screw
   Fig. 5: Lift the bezel/trim piece away from the headlight assembly
   
   
6. Remove the retaining spring by carefully using a hooked end tool, such as a cotter pin removal tool to move it to the side.
7. Remove the headlight from the aiming pins by rotating the headlight toward the center of the car.
8. Unfasten the 4 retaining ring screws, then remove the ring. Fig. 6: With the hood closed, you can see the 4 headlight retaining ring screws (1) and 2 aiming screws (2)
   Fig. 7: Remove ONLY the 4 retaining ring screws, do NOT touch the aiming screws
   
   
9. Remove the headlight pump from the mounting bracket, unplugging the socket as you pull it away. Fig. 8: Remove the headlight away from the mounting bracket, unplugging the socket as you pull it away
   To install:
   
10. Install the headlight bulb, making sure it is plugged in properly.
11. Position the retaining ring and secure with the 4 screws.
12. Position the headlight into the aiming pins. Move the retaining spring back into place.
13. Install the bezel and secure with the retainers.
14. Turn the headlights on, then connect the headlight motor wire.
15. Turn the headlights off. Both should lower.
16. Close the hood. Check the aim of the headlights, and adjust if necessary.

1989–96 Vehicles

1. Open the hood.
2. Open the headlight door halfway. This can be done either by turning the headlight switch on, then back to the parking lamp on position, or by the manual headlamp control knob (which is located on the inboard side of the headlight door). NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
   
3. Remove the screws from the front of the headlight bezel. NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
   
4. Remove the Phillips head screws from each side of the headlight bezel.
5. Remove the bezel by pulling it straight out from the engine side of the hood. Fig. 9: View of the headlight bezel mounting
   
   
6. Unfasten the screws from the headlight retaining ring.
7. Remove the headlamp from the assembly, unplugging the electrical connector as you are pulling it away. Fig. 10: Exploded view of the headlight assembly
   Fig. 11: Location of the headlight mounting and aiming screws
   To install:
   
8. Attach the headlight electrical connector.
9. Position the retaining ring and install the screws securing the ring to the headlight.
10. Position the bezel in place on the headlight assembly.
11. Install the screws on each side of the bezel and tighten to 51 inch lbs. (5.8 Nm).
12. Install the screws on the front of the bezel and tighten to 17 inch lbs. (1.9 Nm).
13. Cycle the headlamps, then close the hood. Check the headlight aim, and adjust if necessary.

Removing the bezel is with a small flatblade between the door handle and the bezel, there are two or three plastic clips that you gently pry towards the outside of the bezel while pulling out on bezel. Don't try this when the car is in cold conditions if possible as the plastic is more brittle then. Best to do inside heated garage or after heating up bezel somewhat.

First you will have to remove the bezel around the radio. This bezel will also be from top to bottom. The bezel is snapped into the vehicle. Pry it out very carfully. Clips will be located at the top, middle, and bottom of bezel. Once snapped out, unplug harnesses so that you can easily work with radio and will help with not scrathing bezel. Once the bezel is out of the way, there will be four screws, 7mm or 9/32 use either socket size, that will be holding radio in place. Remove screws and then pull out radio. Use an aftermarket wire harness to make your installation easier. Install bracket and radio using screws removed and resnap bezel in place.

UNSNAP PUSH-PIN FASTENERS FROM BOTTOM OF CENTER CONSOLE
AND REMOVE BOTTOM PANEL.
2. EXTRACT 4 SCREWS FROM BOTTOM EDGE OF BEZEL. EXTRACT 4
SCREWS FORM INSIDE DASH BELOW POCKET. PULL CUP HOLDER/
POCKET ASSEMBLY OUT OF DASH AND REMOVE.
3. OPEN GLOVE BOX AND REMOVE STOPPERS. EXTRACT 2 SCREWS
FROM RIGHT SIDE OF CENTER DASH BEZEL..
4. FROM BELOW STEERING WHEEL EXTRACT 2 SCREWS FROM BOTTOM
EDGE OR PANEL, UNSNAP UPPER EDGE OF PANEL, UNPLUG, AND
REMOVE.
5. UNSNAP TOP EDGE OR CENTER LOWER BEZEL, UNPLUG, AND REMOVE.
6. EXTRACT 2 SCREWS FROM SIDES OF POCKET.
7. UNSNAP RADIO/AC CONTROL DASH BEZEL, UNPLUG, AND REMOVE.
8. EXTRACT 2 SCREWS FROM EACH SIDE OF THE RADIO BRACKET
ASSEMBLY TO REMOVE RADIO FROM DASH/AC BEZEL.

1. Disconnect and isolate the battery negative cable.
2. Remove Over Steering Column Bezel Replacement.
3. Remove over steering column bezel.
4. Remove left end cover.
5. Remove screw at left end of cluster bezel and headlamp switch.
6. Remove screws holding cluster bezel to instrument panel from each side of steering column.
7. Disconnect clip holding cluster bezel to instrument panel from above right vent louver.
   1. Separate cluster bezel from instrument panel.
   2. Disconnect wire connectors from back of the bezel.
   INSTALLATION
   
   1. Connect wire connectors into back of the bezel.
   2. Place cluster bezel in position on instrument panel. Use care not to place hands on louvers.
   3. Connect clips to hold cluster bezel to instrument panel. Use care not to add pressure on the A/C louvers to seat the cluster bezel clips.
   4. Install screws to hold cluster bezel to instrument panel on each side of steering column.
   5. Install screw at left end of cluster bezel and headlamp switch.
   6. Install left end cover.
   7. Install over steering column bezel.
   8. Install lower steering column cover.
   
   I wouldnt Recomend This Procedure To Anyone juse for Cleaning Purposes Unless Your VIEW OF IT IS "SERIOUSYL IMPARED IF it Moisture Has Accumilated Behind Face of it Then Find Out WHY and Resolve THAT PROBLEM FIRST Onherwise Here you Are. Have A Great DAY !! And Please Dont forget to RATE Me Thank You !