Question about Cars & Trucks

1 Answer

My 98 Chevy truck blew holes threw the oil pan and still runs help please

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 15,973 Answers

What help do you need?

Posted on Apr 26, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 131 Answers

SOURCE: Oil Pan 1998 k2500 7.4 liter engine

You will have to remove your engine. You still will not have enough room to remove the pan from you big block by just trying to raise it.

Posted on Jul 19, 2008

  • 72 Answers

SOURCE: How do I raise the 96 ford f150 truck to repair the oil pan

get a set of ramps to drive up on, or a bigger floor jack. ramps are the easiest.

Posted on Nov 27, 2008

landsend
  • 1066 Answers

SOURCE: 2001 VW 1.9L TDi OIl pan and pump

well if you can get a new pan, gasket and oil pump for $150...by all means replace it.

Posted on Mar 21, 2009

  • 135 Answers

SOURCE: i am replacing the oil pump on a 98 chevy malibu,

take loose the motor mount bolt and jack the front of the engine up to clear the oil pump and remove the pan,.the bolt the runs thru the center of the mounts ,the easiest way ,hope this helps you, thanks robert b.

Posted on Jun 30, 2009

  • 834 Answers

SOURCE: removal procedure of oil pan for a 1997 chevy

To remove the engine oil pan either the engine has to be lifted all the way off of the motor mounts and the oil pan should just clear the flex-plate and transmission, or the front axle dropped down out of the way, or the transmission and flex-plate will have to be removed.

Usually if the engine can be lifted enough to fit a piece of 2x4 wood between the motor mounts and the frame then the oil pan will usually just have enough clearance to be removed from the rear and the oil pan should just clear the transmission and the flex-plate. Also, be sure to check that the fan blade does not damage the fan shroud when lifting the engine.

Let me know if you require any further assistance.

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would make a hole appear in my oil pan passenger side over the starter replaced heads placed new manifold gaskets and new fluids started up and fluids blew up thru the dip stick.


If oil come out of the dip stick that mean your compression goes in the crank case insted of the compression chamber look like bad head gasket sorry

Mar 25, 2015 | Cars & Trucks

1 Answer

How to change the oil pump on 2007 chevy 4.8


Remove oil pan.
Mark and Remove distribuator.
Remove bolts to oil pump and remove.
Install new oil pump.
Reinstall oil pan with new gaskets.
Put in new engine oil.
With a large straight screwdriver. Rotate oil pump (clockwise for top) through the distribuator hole until a huge anount of resistance is felt.
Reinstall distribuator where marked. ( you may have to rotate tang on oil pump to get distribuator to go down. .

Start and run.

Jul 01, 2014 | Cars & Trucks

1 Answer

My 2005 Chevy Cavalier is severely leaking oil from a bolthole on the bottom of the oil pan. It is not the oil plug hole and there are a few holes like it without bolts in them but there is only one...


SOUND LIKE HOLE IN OIL PAN IF THE OIL PAN DRAIN PLUG NOT LOOSE OR MISSING AND THE UPPER PAN BOLTS HOLES NOT MISSING A BOLT CAUSE LEAKING.MORE LIKELY YOU HAVE HOLE IN THE OIL PAN.

Jul 21, 2011 | 2005 Chevrolet Cavalier

1 Answer

My 58 Chevy 348 engine is holding oil in the upper part of the engine I've checked the oil before starting and it is full but after approx. 2 min. running the oil pressure is gone. I check the oil again...


Try using high pressure air to blow out oil returns. The engine may have sludge build up due to foreign material sticking in oil drains from a 52 year old chevy. Love that engine. It was good in it's day! Good luck!

Sep 05, 2010 | Chevrolet Impala Cars & Trucks

1 Answer

I'm looking for how to check the transmission fluid level in a 98 Chevy Cavalier that does not have a dipstick.


Vehicle running in Park. A plug has to be removed from the case - front edge of trans case, passenger side, about two inches up from pan rail. If oil trickles out of hole, it is fine. If not, add fluid up on top through the hole (red cap) until it runs out below. Then replace plug before you shut off the vehicle.

Strange I know..... you should see the 02 and up Explorers!! Hate em

May 15, 2010 | 1998 Chevrolet Cavalier

3 Answers

I just replaced the gasket of the transmission pan and still have a leak on my 1999 chevy suburban?


The leak is coming from the pan ??
Maybe the leak is traveling to the pan seal area from somewhere else ?
Did you scape off the stuck-on old gaskit on trani and pan ?
Its customary to use gaskit sealer on both sides of the new gaskit..

Aug 13, 2009 | 1999 Chevrolet Suburban

1 Answer

I am replacing the oil pump on a 98 chevy malibu, i took all the bolts out of oil pan and cant figure out how to remove the pan to get to the pump. andy suggestions?


take loose the motor mount bolt and jack the front of the engine up to clear the oil pump and remove the pan,.the bolt the runs thru the center of the mounts ,the easiest way ,hope this helps you, thanks robert b.

Jun 11, 2009 | 1998 Chevrolet Malibu

1 Answer

How do i change the oil pump on 98 chevy malibu


Are you sure it's the oil pump, Most of the time it's the oil sensor that has gone bad. Just trying to save you lot's of job since the oil pump is at the bottom of the engine in the oil pan. You can check by having the engine running and looking down the hole where the oil filler cap goes. Rev the engine up a bit and you should see oil splashing around which means your oil pump is working. Your oil pressure is created by the crank shaft. Good luck 

Apr 08, 2009 | 1998 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...