Question about Cars & Trucks

1 Answer

If one turn signal light burns out do the other 3 stop working

Turn signals front and back just stop working

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

If you have one in the front and two in the back, on one side, one bad bulb can make the other two light up but not flash. Each side is separate from the other side.

Posted on Apr 25, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1998 wrangler turn signal/brake light short

your socket may not be grounded properly, I have seen this before, and the simplest way to fix is change the socket with a new one.Not another used one it may also be bad.

Posted on Sep 06, 2008

  • 5 Answers

SOURCE: Chevy Cavalier 2001 turn signal blinks fast

If new bulbs don't work, it is probably the harness that holds the bulb. I had to replace both on my car after fighting with the problem for over a year and not knowing.

Posted on Mar 19, 2009

  • 12 Answers

SOURCE: Turn signals dont work 97 Geo Metro

I had that problem on a 90 Metro. I found a plug located on the top side of of the fuse pannel under the dash came unpluged.

Posted on May 10, 2009

kidspeedy
  • 321 Answers

SOURCE: left rear turn signal light on my 1999 chev. s10 is not working

any increase in bink speed is direcly related to a bulb being burt out.

Posted on Jun 12, 2009

  • 1 Answer

SOURCE: Beeping Noise/Blinker Noise

I thought the same thing. In the past with this car that was the case, it needed a lightbulb replaced somewhere on the car. So after replacing 4 lightbulbs on the car, it still makes the noises...question for someone: I did notice that when i open the doors on the car, the dome light does come on but there are no lights down by the floor in the front of the car...if these bulbs are burnt out too then I will need to replace these and maybe the ticking noises will stop? Are there lights for the floor area on the 2003 Alero model?

Posted on Mar 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right rear turn signal works, brake light works, Front turn signal will not blink.


Looks can deceive you. If the front light comes on when the turn signal is on but there is no blink you need to find a burned out bulb on that side. Many cars have more than one bulb in the rear. One bulb out of the set can stop the blinking.

Feb 17, 2015 | Cars & Trucks

1 Answer

TURN SIGNALS


Hi

Did you check the fuses for the turn lights? Do the
parking lights work? If the parking lights work then you probably have a
problem either in the switch or in turn signal module thing.
The burned out bulb is what might be causing it not to blink... if one bulb is burned out you gotta replace it, make no difference if front or back,the left blinker will not work if the left front or rear bulb is bad.
same with the right side. if the front right or rear right turn signal
light is burned out it will not work.....get replacing the bulbs.Hope this solves your problem.Please rate me if my solution helped you.

Regards,
bonefirediv.
slide_cars_trucks.jpg

Apr 12, 2014 | 1988 Ford Taurus

1 Answer

On my 2004 impala, the front right turn signal doesn't work, (only works with hazard lights). And the back right signal is fast. The signal "clicking" sound is non stop but on the other hand...


If the turn signal filament of the right front park/turn lamp is known to be OK and the hazard switch is in the normal position, the hazard switch or the turn signal/multi-function switch could be defective

Oct 16, 2012 | Cars & Trucks

1 Answer

/'left front turn signal works but not when headlights are on


1. check your turn signal light bulbs to see if one is burned out or partly burned out. One filament may be broken. Do it with lights on and off. Check brake lights. If one not working that is the problem bulb. Check front and back lights.

2. replace your turn signal flashers in fuse panel

Oct 04, 2012 | 2006 Chevrolet Uplander

1 Answer

Turn signal lights not working. turn on emergency flashers and the right signal flashes and bath back lights and the front right flash but the left front don't. any idea's


The 2 filament on the LH Front turn signal is most likely burned out, ...........or the ground to it, & the entire socket needs replaced. Caution lights, send signals to ALL FRONT & REAR lights. All turn signal lights must be in working order, as it is a "pulsating" currect surge sent to the bulbs, LH or RH, depending which direction you wisk to turn. If 1 filament is broken, the circuit is incomplete, & no flash will occur. Usually you will get one light that stays on, & the front or rear missing lighting, is the one whichis the culpret.

Aug 29, 2011 | 2001 Ford F150 Styleside SuperCrew

1 Answer

1997 Porsche 911 993 right turn signals burn


hello there
have you solved your lights problem?

proporsche

May 29, 2010 | 1997 Porsche 911

1 Answer

Signal lights flash faster than normal, back signals work front ones do not, front lights work when head/parking lights turned on.


The fast signal flashing indicates that you have a burned bulb (or one of the bulb elements is burned).
Based on your saying it's the front one on the side your flasher control is set when the signal light flash faster

By a new bulb light and replace the faulty one
hope it will help

Dec 28, 2009 | Mazda B2200 Cars & Trucks

1 Answer

Driver side signals only work when headlights are OFF


What may have happened is either the headlights wiring or the parking lights wiring somewhere along the wiring fused to the left turn signals wiring. Depending on if the turn signals go on when you put the parking lights on or the headlights on.

If the signals come on when you turn on the headlights than you only need to locate the light green wire that comes off the left turn signal harness.

Next follow that wire the entire way back to the firewall looking for another wire fused to that wire as you go.

If there are no signs of this you need to continue looking on the other side of the firewall all the way back to the turn signal and hazard flasher unit which is a black box that connects to a black harness located next to a grey harness behind the knee bolster.

But if the signals come on when you turn on the parking lights than you will also need to check the wiring from the rear left signal and follow that light green wire all the way back to the turn signal and hazard flasher unit.

This should fix your problem, but if not than your problem may lay within the the wiring between the turn signal/hazard switches and the turn signal and hazard flasher unit.

Also you may have a burnt circuit in the junction block. This block is where the light green from the rear left signal and front left signal meet. Don't have a description but if you cannot find it let me know and I will go out to the yard and look myself and let you know.

Apr 22, 2009 | 2004 Dodge Intrepid

2 Answers

Turn signals dont work 97 Geo Metro


There is probably something shorting the front turn signal wires; the car is supposed to turn the signal light circut on and leave it on if it detects a burned out light bulb. The flashers, however, are supposed to work normally no matter what happens.
Hope this helps!

Nov 10, 2008 | 1997 Geo Metro

1 Answer

1998 wrangler turn signal/brake light short


your socket may not be grounded properly, I have seen this before, and the simplest way to fix is change the socket with a new one.Not another used one it may also be bad.

Jul 30, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...