Question about Cars & Trucks

1 Answer

Wher is the crank sensor on a 2005 Nissan pathfinder I believe it's on top of bell housing somewhere any tips would be greatly appriciated

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 563 Answers

I would guess your right. AutoZone has free repair manuals available online.

Posted on Apr 25, 2013


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 41 Answers

SOURCE: hand brake nissan pathfinder

If you lift the hand brake you should find an adjustment nut (I think it is 10MM). Tighten that and you should be good to go. Be careful, it doesn't take much to adjust - turn gradually/slowly.

i hope i was able to help you with your problem! tc!

Posted on Oct 12, 2008

  • 26 Answers

SOURCE: life expectency of 2005 Nissan Pathfinder engine?

all i can say is nissan are very well known for exceeding 200,000 miles

Posted on Dec 29, 2008

  • 260 Answers

SOURCE: 97 nissan pathfinder cranks but wont start no spark

Did you try looking through the fuse panels or relays?

Posted on Apr 09, 2009

  • 321 Answers

SOURCE: knock sensor 1996 v6 3.3 nissan pathfinder

The Crankshaft Position Sensor is located: Under hood, driver side, front engine area, mounted rear of crankshaft pulley
The Knock Sensor is located: Under hood, center, front engine area, below intake manifold, mounted on block

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: automatic transmission dipstick location for 2005 nissan pathfinder

The dipstick is located under the air cleaner on the right-hand side, identified by a yellow ring.

Posted on Jun 28, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2005 nissan quest crank sensor location?

trans lower bell housing if memory serves right

Aug 25, 2014 | 2005 Nissan Sentra

2 Answers

How to replace a crank case sensor on 1996 nissan pathfinder?

Crank case sensor? Sorry, I don't think I've ever heard of one. Crank position sensor? (Prob top of the bell housing directly behind the cylinder head, 10 mm headed bolt holds the shield and the sensor in place, but is only used when trouble shooting misfires.)

Jun 30, 2014 | 1996 Nissan Pickup

1 Answer

Location 2004 nissan frontier camsheraft sensor location 4.0lit

the VQ40 engine has 2 cam sensors, they at the back of the cylinder heads at the firewall above the bell housing. the connectors have a green lock tab that needs to be pushed into the connector then while holding the green tab in pull the connector off the sensor

Nov 06, 2013 | 2005 Nissan Pathfinder

1 Answer

I'am trying to find wher is the crank sensor located on a 2002 kia opitia v-6 2.7

Hi Di,
I believe that the sensor is located on the front of the engine adjacent to the front pulley, however if it's not there, it will be located adjacent to the fly wheel inside the bell housing. It is always connected via a screened cable.
Regards Johngee10

Mar 08, 2011 | 2004 Kia Optima

1 Answer

I was told my crank sensor is bad . Where is it located on the car? It was not cranking right, It was like it is flooding.

Nissan recalls that problem to reprogram the ECU. What happens the crank sensor electrical terminals seep oil into the crank sensors plug. The new metal crank sensors correct this problem.

Look on the fire wall side of engine between the rear engine mount and the transmission bell housing, there is only about 2 inches space for you to work with. You may have to remove the rear engine mount if your hands are bigger than mine and you have to remove this sensor from the top side of the engine.

Dec 21, 2009 | 2005 Nissan Altima

1 Answer

Where is cranshaft position senser on 97 nissan pathfinder

The Crankshaft Position Sensor (CKP) is mounted on the top of the transmission bell housing. Assuming you are talking about the 3.3L V6.
The crank position sensor (ckp) is located at the back of the motor,driver's side, mounted to the transaxle housing. It gets it's single from the flywheel teeth. First unplug it and then remove the retaining bolt and pull it up and out. Reverse precedure to install.

Sep 29, 2009 | 2000 Oldsmobile Alero

2 Answers

Where is the crankshaft position sensor on a 2002 crysler Sensor(Cant Find It)

well it is near the to of bell houseing on trans side it should be coming out of bell housing at trans

Aug 14, 2009 | 2005 Chrysler Town & Country

1 Answer

Replace starter in a 97 Pathfinder

im not sure but it should be somewhere around the transmission bell housing

Sep 28, 2008 | 1997 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides