Question about 1993 Toyota Previa

Open Question

1993 toyota previa cylinder head bolts torque

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

Ad
  • 3 Answers

SOURCE: 1992 Toyota Previa van,Oil dripping onto exhaust manifold, replace head gasket? need a free manual!

The toyota previa uses a formed silicone gasket for the valve cover and the cover is held in place by metric shoulder bolts ( 10mm). The valve gasket leaks because you can't get enough preload on the bolts to re-seat the old gasket when it gets old and shrinks. The shoulder bolts only allow you to tighten the gasket enough to seat the shoulder on the bolt. If you continue to torque down the suspected bolts, you will snap the bolt off ( don't ask me how I know this ). You can either 1.)replace the old gasket with a new one or 2.) remove the existing bolts around the leak area and put in new metric bolts that do not have a shoulder. You may want to put in a small sleeve into the existing bolt hole but shorter than the thickness of the valve cover to account for the smaller diameter bolt. You can now torque down the bolt and get enough preload to seal the valve cover without removing the old gasket. Make sure you use a torque wrench ( in-lbs) or be very careful not to snap these small valve cover bolts.

Posted on Jul 15, 2009

Pelukes01
  • 52 Answers

SOURCE: what are the cylinder head torque settings for a

0900c1528006efe6.jpgUmiformilly tighten each of the ten head bolts in several passes, in the sequence shown. Tighten them to 44 ft. lbs. (60 Nm).

Posted on Jul 23, 2010

  • 496 Answers

SOURCE: I need the torque settings

cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Posted on Feb 22, 2011

solarstarene
  • 159 Answers

SOURCE: whats the valve clearance for toyota 4k engines

valve clearance is .20mm for the intake and .30mm for the exhaust. Will try to find cylinder head torque for you.

Posted on Mar 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I require the cylinder head attach bolts tightening sequence and torque values for a 1993 2.0 I 4 cylinder toyota camry situated in south africa


go on line to google-type in Toyota camry bolt tensions and specifications and there should be a pdf sheet with that information.

Dec 30, 2014 | Toyota Cars & Trucks

1 Answer

Toyota 5afe head bolts torque


Toyota 4A/ 5A-FE Cylinder Head Torque:
(a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
(b) Install the plate washer to each cylinder head bolt.
(c) Install and uniformly tighten the ten cylinder head bolts in several passes in the sequence.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)
HINT: Cylinder head bolts are in length of 90 mm
(3.54 in.) and 108 mm (4.25 in.). Install the 90 mm
(3.54 in.) bolts (A) in intake manifold side positions.
Install the 108 mm (4.25 in.) bolts (B) in exhaust
manifold side positions.

Mar 31, 2014 | 2003 Toyota Corolla

1 Answer

I need the torque settings for toyota corola 1993 cylinder head torque please ?


Hi Manuel, There are a number of different engines used in the Corolla, knowing which would be a great help. The engines used in the 1993 are of the 'A' series and 'E' series. The torque for the A series is 29 nm + 90 degrees. When removing the head begin loosening from the outer bolts. When the head is off have it inspected for warpage and skimmed if it is required. Tightening any cylinder head always begins at the middle or centre and works outwards. As my friend has said, the camshaft caps are tightened to 9 nm and the inlet manifold goes to 24 nm, and the exhaust is 27 nm. The tappet cover I think is 29 nm. The tappet cover is tightened on the A series with nuts onto the plug tubes. Regards John

Mar 29, 2014 | 1993 Toyota Corolla

1 Answer

Torque specification


Apply a light coat of engine oil on the threads and
under the heads of the cylinder head bolts.
- Install the plate washer to each cylinder head
bolt.
- Using Torque wrench, install and uniformly tighten the ten
cylinder head bolts in several passes.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)

Jan 26, 2014 | 1993 Toyota Corolla

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Need head bolts tourqe sequence for a 89 tercel


1989 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence809142031993 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence80914199they appear to be the same,other than the torque angle. good luck!

Oct 20, 2011 | 1993 Toyota Tercel

1 Answer

Can't find cylinder head torques!!! please advice....


Torque sequence: ----------------- there are two rows of fasteners and you need to start with the middle 2 fasteners first and then work your way toward the front and back in steps. Step 1: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 10 Ft/Lbs Step 2: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 20 Ft/Lbs Step 3: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 29 Ft/Lbs Step 4: turn all head bolts in sequence an additional 90 degrees Step 5: turn all head bolts in sequence an additional 90-degrees recheck final torque in sequence. Fasteners are supposed to be replaced if they are removed since they are torque-to-yeild fasteners.

7 - 5 - 1 - 3 - 10
front
9 - 4 - 2 - 6 - 8

Apr 17, 2011 | 1997 Toyota Previa

1 Answer

What is the easiest way to remove a headgasket from a 1993 toyota previa


Hello. Welcome to FixYa.

The easiest way to remove the cylinder head is to lower the engine/transmission combination out thru the bottom of the vehicle; ie support the engine/trans, and raise the vehicle off of the powertrain assembly.

Working on the cylinder head whilst the engine is still in the vehicle is a VERY difficult endeavour.

Even though it looks like more work, by lowering the engine out; it proves much easier to work on and access all of the necessary bolts.

Thanks for choosing FixYa for assistance.

Sep 20, 2010 | 1993 Toyota Previa

1 Answer

Toyota windom v6 head bolts torque settings


INSTALL CYLINDER HEAD if any bolts broken or deformed , replace it.

7------2-----4--------6
5------3-----1--------8
FRONT sequence head bolts
8-------1-----3-------5
6-------4-----2-------7

CYLINDER HEAD bolts are tightened in three progressive steps
1. 34 Nm ( 25 ft.lb)
2. 90 degree
3. another 90 degree.

double check everythings before install the head,
be sure to install the GASKET correctly.

Hope this can help.

Apr 19, 2010 | 1993 Toyota Camry V6

1 Answer

1993 Previa. Fuel floods the cylinders after long drive & parked


try running an injector cleaner thru the system.
you may have a dripy injector.

Nov 10, 2009 | 1993 Toyota Previa

Not finding what you are looking for?
1993 Toyota Previa Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8825 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...