Question about Cars & Trucks

1 Answer

Common problem why clutch booster hard to push

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

  • Expert
  • 72 Answers

That's because your clutch booster are bad and less of enough pressure , try to replace a new clutch booster , also may change brake booster, you can find more info at our site: http://www.fiverhope.com

Posted on Jul 05, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1991 Toyota p/u 4 cyl.when clutch is in and brakes on I have low and high eng.idle


think you need to check the front pulley ? with someone pushing the clutch up and down check for movement of the pulley if its moving in and out then you you need new crankshaft thrust bearings but it could be the actual crank has worn on the face that pushes on the thrust bearing ,common problem on older cars ,when at traffic lights always neutral /handbrake on foot off the clutch or am i old fashioned

Dec 02, 2016 | Toyota Cars & Trucks

2 Answers

My brakes are hard to push on my 2005 ford freestar what could cause that to happen ?


this is almost always a problem with the power brake booster, check to see if the hose is loose, has a hole or is split at one to the ends. If there is no vacuum leak, it is probably going to need a new booster. It is hard to get at, as it is under the window wiper transmission. that mechanism is not too difficult to remove, which will give you a lot of room to repair or replace the hose or the unit itself.

Apr 07, 2014 | Cars & Trucks

1 Answer

87 toyota clutch wont engage after brakes were replaced


Brake and clutch are vacumme assisted and hard to start seems like vac hose left of of has leak

Nov 14, 2012 | Toyota Cars & Trucks

1 Answer

It is hard to push my clutch in as well as the gear shifter is tough to move into gears...any ideas?


Hi and welcome to FixYa!

You may need to bleed the clutch as a first course of action and observe if it will do it. If the problem still persist then go for the primary and secondary clutch booster. If they are worn out it tends to stuck that's why the gear shift is hard to engage for it is not performing properly.

Hope this helps and thank you for using Fixya! Have a good one!

Jan 23, 2011 | 2002 Ford Mustang

1 Answer

The clutch peddle has less tension and its hard to shift gears


You may have a worn out clutch or a bad/ worn out clutch actuator cylinder. Your truck uses a hydraulic booster for your clutch, and those commonly wear out. But to make sure bring it to any mechanic to have it checked out.

Dec 13, 2010 | 1991 Isuzu Trooper

2 Answers

My break pedal is hard to push & i can here air when the peadel is pushed into stop, and is this connected to the abs if there is one on my model.. thanks for your help. would this be the brake...


not sue u have abs on that model
more than likely break booster
best way to check booster is stop truck pump pedal a few time then put your foot on brake pedal and push down this is with truck stopped ,keeping pedal pushed start engine brake pedal should move down more if booster is working check all pipes tp booster

Sep 29, 2010 | 1995 Toyota 4Runner

1 Answer

Brakes not working properly when you press the brake pedal becomes hard and pushes against pressure


Sounds like the booster. It is located on the drivers side firewall and has the brake fluid resevoir attached to it. Make sure your resevoir has fluid in it as this can affect braking, but not vacuum boost. Look for a vacuum leak, as the booster works on manifold vacuum. If this is not the issue, you may need to replace the booster, but the most common cause of this is loss of vacuum. Good Luck! I hope you find this to be very helpful!

Dec 07, 2009 | 2000 GMC Jimmy

1 Answer

Check brake booster


You can check the booster.First check vacuum to booster,is it strong?,it needs to be.Check the check valve that the vacuum hose slips onto.It should only be one way,blowing threw it and not being able to blow threw it the other way.If this is all ok,then think about this,Are the brakes really hard to push down?or just going to the floor,or spongy,or anything else?If the brakes are hard to push,then replace the booster,if the brakes do anything else,it`s not the booster.The booster only,I repeat,only, make brake pedal easy to push.If I can help.>>>roniecon@gmail.com

Aug 18, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Clutch pedal too hard too push in 94 might max


Bad presure plate. The clutch is made up of two parts, the clutch disk and the presure plate. as the vehicle gets older the pressur plate can bend making it imposible to push the pedal in. This is very common if your vehicle has a clutch cable as compared to a hydrolic clucth but happens with both just the same. The solution is replace the clutch.

Mar 08, 2009 | 1990 Mitsubishi Mighty Max

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...