Question about 2000 Chevrolet Blazer

Open Question

2000 chevy blazer antitheft devise reset

Replaced ignition lock on my 2000 chevy blazer after an attempted theft now my car starts but dies. can you help

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: Chevy Tahoe 2004 Anti Theft Device has been activated.

leave the key on for about 5 to10 min then try to start. Are reset to computer by leaving the key on for 10 min and try to start the vehical.Do this procese 3 time then it shold reset

Posted on Feb 12, 2009

Suraido
  • 195 Answers

SOURCE: 1996 chevy cavalier. problems starting and running

Actually i doubt the switch is in default here. Especially that if i'm not mistaken the theft light on those was only on the monsoon radio systems and only tells the status of the theft lock on the radio. And if the theft lock light on the radio comes on it's because it thinks it's being unplugged. Taking that in account and reading all the problem you have with the car, i'm strongly leaning toward a grounding problem. So check the negative post on the battery to be sure its not moving or broken in any way, and verify all the grounding wire and straps and replace them if needed. Not many people know this but the ground wires on a car are 100 times more important than the positive wires. Without the grounds, the current has nowhere to go on any components, so that means even the spark plugs stop sparking. If all the grounds are good, just check the battery itself and the alternator just to be sure they are not causing these problems. And if all else fails, then it would be option to change the ignition switch/cylinder. Pretty sure though that you can find one in a scrap yard for less than 150$, those cavaliers are practically raining everywhere in the scrap yards, and you can also use one from a pontiac sunfire which is the same car. Also, you can use most switches from other GMs in the same years, like a grand am, grand prix, lumina, etc. Just make sure that the car you take it from has basically the same equipment more or less than your cavalier so that the zenith has the same number of wires as yours and same positions also.

Posted on Jul 08, 2009

  • 324 Answers

SOURCE: how replace turn signal switch 2000 chevy blazer?

Since the 2000 chevy blazer is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.

Posted on Oct 07, 2009

  • 1 Answer

SOURCE: 98 Malibu Theft control ignition shut off activates when starting the car

with the 1998 anti theft what would the dealer do that a different wont do .the anti theft light id on on car wont stay on..i need help.ami1998

Posted on Nov 23, 2009

  • 1 Answer

SOURCE: 1997 chevy blazer ignition switch

1997 blazer put car in park shut it off but, key won't turn far enough back to come out

Posted on Jan 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to reset anti-theft on a 2000 alero


The security, antitheft or lock picture/icon is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterprets this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle. This link explains it pretty well.
http://www.diy-gm-security.com/

25627937-vycpj41x2iphfdmbx4v0vfed-3-0.jpg

Apr 04, 2015 | 2000 Oldsmobile Alero

2 Answers

How do i bypass key i d system on a 1998 chevy blazer


The security, antitheft or lock picture/icon is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterprets this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle. This link explains it pretty well.

http://www.diy-gm-security.com/

Mar 30, 2015 | 1998 Chevrolet Blazer

1 Answer

How to reset anti theft system on a 2008 chevy impala


The security, antitheft or lock picture/icon is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterprets this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle. This link explains it pretty well.

http://www.diy-gm-security.com/





Perform the re-learning procedure


  1. Turn ON the ignition, with the engine OFF.


  2. Attempt to start the engine, then release the key to ON (vehicle will not start).


  3. Observe the SECURITY light, after approximately 10 minutes the light will turn OFF.


  4. Turn OFF the ignition, and wait 10 seconds.


  5. Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes ( the vehicle


  6. is now ready to relearn the Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK).


Start the engine (the vehicle has now learned the Sensor Data Code and/or password).

Feb 21, 2015 | 2008 Chevrolet Impala

1 Answer

How to reset security code in 2001 chevy blazer


The security, antitheft or lock picture/icon is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterprets this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle. This link explains it pretty well.
http://www.diy-gm-security.com/
http://newrockies.com/

Jan 06, 2015 | 2001 Chevrolet Blazer

1 Answer

2000 Chevy Impala will not start... was driving it on Saturday when breaks & power steering went out. When car was pulled over and put in park, engine died. Now car only makes a single...


The security, antitheft, or passlock light is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterperates this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle.
This link may help you find ways to bypass this or fix it yourself.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Apr 15, 2013 | Cars & Trucks

1 Answer

How to reset security system in 2000 chevy blazer


The Security light is a visual indication that something in the car's antitheft system is failing. In most GM cars there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterperates this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle.
This link may help you find ways to bypass this or fix it yourself.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Mar 19, 2013 | Cars & Trucks

1 Answer

Nw truck starts and dies almost immediately?replaced passlock ignition housing on 2000 chevy silverado 1500 2wd 5.3 engine,


The security, antitheft, or passlock light is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterperates this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Mar 19, 2013 | 2000 Chevrolet Silverado 1500

1 Answer

How to reset antitheft


The security, antitheft, or passlock light is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterperates this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle.
This link may help you find ways to bypass this or fix it yourself.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Feb 27, 2013 | 2000 Chevrolet Blazer

1 Answer

Chevy cobalt wont start has the security ligh on and check airbag lights. struggles to starts then dies


The security, antitheft, or passlock light is a visual indication that something in the car's antitheft system is failing. In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM (Theft Deterrent Module). These 3 parts are in CONSTANT communication. If the key is in the ignition, then these parts are sending signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, the car misinterperates this as an attempt at theft and goes into antitheft mode. The car thinks its being stolen or hotwired because it is not getting that signal from YOUR specific key. This is why the security light turns on and shuts down your vehicle.
This link may help you find ways to bypass this or fix it yourself.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Oct 15, 2012 | 2008 Chevrolet Chevrolet Cobalt LT

1 Answer

Chevy Malibu LS (V6-3.1 L) won't start or starts up and IMMEDIATELY dies, how can I diagnose the problem?


Your car starts and dies due to the failing antitheft system. Your vehicle is not receiving the "fuel enable" signal that it needs to keep running. So the injectors get turned to off to prevent theft. You will need to diagnose which part of the antitheft system is failing. Or bypass the entire security system. This link will help you understand the problem, and depending on the year of your vehicle, possibly a good bypass solution.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

May 18, 2012 | Cars & Trucks

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...