Question about Cars & Trucks

Open Question

Location of #2 cylinder on chrysler town and country

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

lebones337
  • 152 Answers

SOURCE: Where is the Body Control Module located?

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the bcm.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the bcm to the jb. Slide the bcm downward to disengage guide studs on jb from channels on bcm mounting bracket
Remove bcm from jb.

Posted on Jan 02, 2009

chryslertech
  • 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

emissionwiz
  • 75814 Answers

SOURCE: where is the body control module located on a 1997 town & country

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Posted on Mar 23, 2009

  • 323 Answers

SOURCE: locassion of output speed sensor on 2003 Town and Country

The input and output speed sensors look identical on the connector side. The one over the solenoid pack is the input, the one closer to the left frame rail or left front wheel is the output sensor. I hope this helps.

Posted on Apr 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

#1 cylinder is misfiring, put new fuel ejector and the problem is still there.It has a bad noise in the motor.


Thread: Cylinder 1 misfire P0301 - The Chrysler Minivan Fan Club ...

forum.chryslerminivan.net/showthread.../27978-Cylinder-1-misfire-P03...

Feb 6, 2013 - 7 posts - ‎4 authors
My mother-in-law's 2002 Town and Country has the P0301 cylinder 1 misfire error code. I haven't done much work on this type of car, so I'm not ... '05 Town & Country Cylinder 1 misfire mystery
10 posts
Feb 3, 2014
Engine misfire
7 posts
May 6, 2012
#1 Cylinder misfires at idle only
10 posts
Jun 4, 2011
Running rich / Misfire Mystery
10 posts
Sep 20, 2010
More results from forum.chryslerminivan.net

Part 1 -How to Test the Coil Pack (2001-2008 Chrysler 3.3L ...

easyautodiagnostics.com > Chrysler > 3.3L, 3.8L
Apr 29, 2011 - Page 1 of 7: How to Test the Coil Pack (2001-2008 Chrysler 3.3L, 3.8L). ... This article will help you troubleshoot a Misfire Condition that might be setting ...your 2001-2009 Chrysler (or Dodge) 3.3L or 3.8L Town and Country, Voyager, ... it's important the you know what 'Paired Cylinders' and 'Non-Paired ...

Jan 03, 2016 | 2001 Chrysler Town & Country

1 Answer

Need diagram for juntion box


Thread: fuse box?? - The Chrysler Minivan Fan Club Forums

forum.chryslerminivan.net/showthread.php/21174-fuse-box

Jun 26, 2011 - 10 posts - ‎3 authors
Does anyone have a diagram for the fuse box (junction box) that is inside on the drivers side for a 1998 Town and Country. I need to know what the relays are for, my manual only shows the fuses and there is ... Forum · The Minivan Mopar Garage · 3rd Generation Chrysler Minivans: 1996-2000; fuse box?Missing: juntion

Interior Fuse Box Location: 1996-2000 Chrysler Town and ...

www.carcarekiosk.com/video/2000_Chrysler_Town_and.../replace
Interior Fuse Box Location: 1996-2000 Chrysler Town and Country ... box of your 2000Chrysler Town and Country in addition to the fuse panel diagram location. ... If youneed to replace a blown fuse in your Town and Country, make sure you ...Missing: juntion

Dec 21, 2015 | 1996 Chrysler Town & Country

1 Answer

Wiring order diagram from coil to spark plugs on a 2006 chrysler town and country


if you haven`t removed all the wires at the same time replace them one at a time. look on the coil tower were the plug wire attaches to it some show the cylinder #. cylinder #1 is rear of motor by firewall and cylinder #2 is front of motor by radiator both on the passenger side. even numbers along front of motor uneven numbers along firewall. cylinder #5 and #6 are on the drivers side of motor.

Sep 09, 2015 | 2006 Chrysler Town & Country

1 Answer

My 2005 Chrysler Town & Country 3.8L V6 . just started misfiring


possible bad injector - recomend have injector checked and or do compression test on cylinder # 2

Jul 07, 2012 | 2005 Chrysler Town & Country

1 Answer

Would a 2001 chryler town and country faulty engine module cause number 2 cylinder not to fire


not likely, since the engine module also fire the plug across from the #2 cylinder on the coil pack. check for spark directly at the coil, if none is found ,then most likely a bad coil pack.

Jun 11, 2012 | 2002 Chrysler Town & Country

1 Answer

Picture of bank1 sensor1 o2 sensor location on 2001 chrysler town & country


I do not have a diagram but, bank 1 is the bank where #1 cylinder is at. other side would be bank #2. so bank #1 o2 sensor is just before convertor.

Aug 29, 2010 | 2001 Chrysler Town & Country

1 Answer

I am looking for the cylinder head torque specification for the 3.3litre chrysler town and country 2003


Tighten the cylinder head bolts 1 - 8 in the sequence shown in Cylinder Head Bolts Location and Tightening Sequence Using the 4 step torque turn method, tighten according to the following values:
Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)
Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)
Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)
Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
NOTE: Bolt torque after 1/4 turn should be over 122 N·m (90 ft. lbs.) If not, replace the bolt.

Tighten head bolt number 9 Cylinder Head Bolts Location and Tightening Sequence to 33 N·m (25 ft. lbs.) after head bolts 1 - 8 have been tighten to specifications.

Jan 24, 2010 | 2003 Chrysler Town & Country

1 Answer

Where is the oxegen sensor located on a 2000 chrysler town and country 3.8 liter. does the oxegen sensor have a fuse


the oxygen sensor is located in the exhuast pipe,there could be more than one sensor, maybe 4 sensors on a 6 cylinder car and 2 sensors on a 4 cylinder car,so youre gonna have to know which one is bad,if the check engine light is on it will tell you which position sensor is bad like bank 1 sensor 2 something like that,also there is NO fuse for the o2 sensors

Oct 19, 2009 | 2000 Chrysler Town & Country

1 Answer

Cam sensor on 2001 Chrysler Town and country


depending on what size motor you have, the 2.4 has the sensor mounted on the rear of the cylinder head. the 3.3 & 3.8 engines have them mounted on top of the timing case cover, Good Luck!

Sep 19, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...