Question about Nissan Rogue

Open Question

Evap canister vent valve

WHERE IS THIS PART 2009 NISSIAN ROGUE

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
maklean
  • 1665 Answers

SOURCE: location of Charcol Canister and

The evaporative emission canister purge solenoid valve is a duty control type, which controls the flow of purge air from the evaporative emission canister.
4a6acf4.gif Inspection 1. Look for loose connections, sharp bends or damage to the fuel vapor lines. 2. Look for distortion, cracks or fuel leakage. 3. After removing the EVAP canister, inspect for cracks or damage. 0e0e1be.gif

Posted on Sep 04, 2008

Ad
  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

savdragon
  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

  • 104 Answers

SOURCE: I have a 2004 Avalanche, 49K mileage, code PO446,

That is an EVAP code. its a vent control code. you can manually test it by powering it up if you know where its at. i cant remember exaclty where its at off the top of my head but its only 2 wires. using a volt meter you want to make sure power is getting to it, but you cannot activate it without dealer scan tool.hmmm if you can figure out which is ground and power when you give it 12 volts it should click. meaning your vent solenoid works and you have wiring problems or its leaking.

EVAP problems are hard to finde with out scanners. you can change the vent solenoid and hope it fixes it. but a code points you to the direction of a problem. hopefull its not wiring problems. in the northern states with snow. ice can pull out wires and also get clogged in the vent solenoid and lock it up. its either wiring or bad or a leaking solenoid. check condition of wires. if they look good try a vent soleniod.

if that doesnt fix it after a engine light reset and 2 weeks or so. then goto dealer. you need to reset it after repair. light will not go off on its own.GOOD LUCK

Michael
ASE certified.
plz rate

Posted on Apr 29, 2009

matney68
  • 426 Answers

SOURCE: Looking for the evap canister vent valve on a 2006 Silverado

if you look underneath the vehicle on drivers side in the area beneath drivers you with see a plastic rectangular sort of shaped box this is evap canister and vent valve is there in this area.

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the purge control valve located on 1998 nissian pathfinder


Location should be back by the fuel tank.

first off, the P1447 DTC is triggered when the EVAP control system isn't operating properly or there is a leak between the intake manifold and the pressure sensor. the parts between the pressure sensor and intake manifold are:

1. EVAP canister purge control solenoid valve
2. EVAP canister purge control valve
3. EVAP canister purge volume control valve (Part # 14930-3M201) YOU WILL HAVE TO DOUBLE CHECK ON THE PART NUMBER WITH THE DEALER FOR THE PRICE.

If you've received this P1447 DTC, chances are that the brick of charcoal in the canister has fallen apart over time, and filled the lines with charcoal. this affects parts 2 & 3 from the above list, and of course the EVAP canister (Part # 14950-1s717 $144.22). but when you replace the canister, you have to replace the EVAP canister vent control valve (part # 14935-54u06 about $100), and don't forget the o-ring (part # 16618-40u00 about $1.60) that goes between the canister and the vent control valve.

If you attack this DTC early enough, all you have to replace is the canister and vent control valve with the o-ring, which will add up to under $300 MSRP...a lot better than paying upwards of $1000 for parts and labor. Don't be scared to do it, it's actually quite simple.

D

Sep 28, 2015 | Cars & Trucks

1 Answer

Where is my vent valve solenoid on my 2006 Chevy Colbalt?


It's located under the vehicle back behind the fuel tank , Installed in the canister ! Remove the EVAP canister vent solenoid valve from the canister !
Rotate the EVAP canister vent solenoid valve counterclockwise in order to release it from the locked position.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister harness electrical connector (2) from the EVAP vent solenoid valve. Clean away any debris that may be present around the EVAP canister vent solenoid valve.
Remove the EVAP canister bolt. Lower the EVAP canister.

Feb 25, 2015 | Chevrolet Chevy Cars & Trucks

3 Answers

WHAT DOES FAULT CODE P1446-00 MEAN


older nissan? evap canister purge fault. check for loose or rotten/disconnected vacuum hoses before testing the vapor canister purge valve.
25439609-xipalmoknr3fbjmp51kycajc-2-0.jpg The charcoal canisters also clog up. Do some diagnosing before you go changing parts.

Feb 16, 2015 | Cars & Trucks

1 Answer

Location for evap vent solenoid on 2009 HHR 2.2L


Under rear of veh behind fuel tank attached to evap canister 25349127-niuon2vreedqwf5ywq4zdfyq-3-0.jpg

Jan 01, 2015 | 2009 Chevrolet HHR

2 Answers

045500 error code on a Chev silverado 1500 2009 5.3 lt what does it say


DTC P0455
  • Evaporative Emission (EVAP) System Large Leak Detected

Jul 23, 2014 | 2009 Chevrolet Silverado 1500

1 Answer

Code p1448


P1448 NISSAN - EVAP Canister Vent Control Valve Open

Possible causes- EVAP control system pressure sensor and the circuit
- Blocked rubber tube to EVAP canister vent control valve
- EVAP canister vent control valve
- Water separator
- EVAP canister is saturated with waterWhen is the code detected?EVAP canister vent control valve remains open under specified driving conditions.

Jun 08, 2012 | 1998 Nissan Frontier

1 Answer

P0446 ford escort 98


This Pinpoint Test is intended to diagnose the following:
  • Canister vent (CV) solenoid (9F945) (electrical concern only)
  • Fuel filler cap (9030)
  • Fuel tank pressure (FTP) sensor (9C052)
  • EVAP canister tube (fuel tank to EVAP canister)(9A228)
  • Fuel canister purge outlet tube (EVAP canister to EVAP canister purge valve) (9D661)
  • EVAP return tube (EVAP canister purge valve to intake manifold) (9G271)
  • EVAP canister purge valve (9C915)
  • Vacuum source line (input port vacuum to intake manifold)
  • Harness circuits: CV, FLI, FTP, EVAP Canister Purge Valve, SIG RTN, vehicle power (VPWR), reference voltage (VREF) and power ground (PWR GND)
  • Powertrain control module (PCM) (12A650)
This Pinpoint Test is used as an assistance in diagnosing the following EVAP components:
  • EVAP canister and bracket assembly (9E857)
    • EVAP canister sleeve assembly (fitting)(9D925)
    • Canister vent (CV) solenoid - hose assembly (9F976 or 9K318)
    • EVAP canister (9D653)
    • Canister vent (CV) solenoid (9F945)(mechanical concern only)
  • Fill limit valve assembly (9A086)
  • Fuel filler pipe flapper valve (9B085)
  • Fuel filler pipe check valve (9189), assembly (9285)
  • Fuel tank filler pipe (9034)
  • Fuel tank assembly (with fuel vapor vent valve) (9K007)
  • Fuel tank assembly (without fuel vapor vent valve) (9002)
  • Fuel vapor control valve (9B190)
  • Fuel vapor vent valve (9B593)
  • Liquid/vapor fuel discriminator (9G332)
  • On-board refueling vapor recovery (ORVR) T - connector assembly (9S314)
Description For additional information on the Evaporative Emission (EVAP) System, refer to Section 1A .
For additional information on the Evaporative Emission System Monitor, refer to Section 1A .
Pinpoint Test Schematics Escort/Tracer (2V)
aa3060b.gif

May 28, 2011 | 1998 Ford Escort

1 Answer

Feul will burp mout of the filler cap no mater how slow I fill the car and the service engine soon light is on, how do I change the feul tank filler vent check valve?


Hi, your EVAP vent valve is likely stuck closed. The valve is under the car near the fuel tank. Remove the valve and check to see if it's stuck. You may be able to restore operation by cleaning the valve with carb cleaner. The valve should be open when no voltage is applied. I have pasted instructions below from autozone.com. Please let me know if you have any questions, and thanks for using FixYa.
jturcotte_1546.gif Vent Solenoid Valve
2.2L & 2.4L Engines

  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.

To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Apr 18, 2011 | 2004 Chevrolet Cavalier

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...